CHERUBINI BLUE WAVE RX User manual

ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
Wave RX
Senso RX
I
GB
D
F
E
MOTORE TUBOLARE CON FINECORSA
ELETTRONICO PER TENDE DA SOLE
TUBULAR MOTOR WITH ELECTRONIC
LIMIT SWITCH FOR AWNINGS
MARKISEN - ROHRMOTOR MIT
ELEKTRONISCHER ENDLAGENEINSTELLUNG
MOTEUR TUBULAIRE POUR STORES
AVEC CONTACT DE FINS DE COURSE ÉLECTRONIQUES
MOTOR TUBULAR PARA TOLDO
CON FIN DE CARRERA ELECTRÓNICO

23
Table of contents:
How to prepare the motor ...................................................................................... p. 24
Electrical connections ............................................................................................. p. 25
Compatible remote controls ................................................................................... p. 26
Key to symbols ....................................................................................................... p. 26
Command sequences example ............................................................................... p. 27
Function open/close programming remote control ............................................. p. 28-29
Setting the rst remote control .............................................................................. p. 30
Automatic disabling of the rst remote control setting function ............................ p. 30
Adjustment of the limit switches ...................................................................... p. 31
Setting the closing limit switch .............................................................................. p. 31
Setting the opening limit switch ............................................................................ p. 31
Deleting the limit switch positions ................................................................... p. 32
Deleting the closing limit switch............................................................................. p. 32
Deleting the opening limit switch ........................................................................... p. 32
Total deleting of the limit switches ......................................................................... p. 32
Setting a middle position ........................................................................................ p. 33
Deleting the middle position .................................................................................. p. 33
Closing force adjustment ........................................................................................ p. 34
Maximum closing force adjustment (100%) - only for motors from 32 Nm -.......... p. 34
Setting of additional remote controls ..................................................................... p. 35
Remote control memory clearing............................................................................ p. 35
Full memory clearing .............................................................................................. p. 36
Special functions
Additional middle position...................................................................................... p. 37
Setting the additional middle position.................................................................... p. 37
Changing the additional middle position ............................................................... p. 38
Deleting the additional middle position.................................................................. p. 38
Short-term setting of a remote control ................................................................... p. 38
Setting the A530058 pocket remote control ........................................................... p. 39
Fabric tightening function ....................................................................................... p. 40
Electric wiring to motor command for UP-DOWN mode
(2 independent UP-DOWN buttons) ....................................................................... p. 41
Command management from white wire ............................................................... p. 42
Super-sensitivity obstacle detection management during downwards movement
- only for motors up to 25 Nm - .............................................................................. p. 42
EU Declaration of conformity ................................................................................. p. 103
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
ENGLISH

24
HOW TO PREPARE THE MOTOR
NB: If you use tubes with a round form, the driving pulley must be xed to the tube, and
the installation is to be paid by the person who installs the system. For other tube sections
the tting is optional, but strongly recommended.
1. Insert the adaptor in the nut mating the
groove with the reference notch and push
till they touch.
2. Fix the driving pulley on the motor pin
until the stop pin clicks.
3. Insert the motor fully in the rolling tube.
STOP RING NUT ADAPTOR
DRIVING PULLEY
STOP RING NUT
1
2
3
ENGLISH

25
ELECTRICAL CONNECTIONS
- In order to prevent dangerous situations or malfunctioning, the electrical command
elements wired to the motor must be sized according to the motor’s electrical features.
- Means for disconnection must be incorporated in the xed wiring in accordance with
the national installation standards.
- For outdoor use, provide the appliance with a supply cable with designation H05RN-F
containing at least 2% of carbon.
- If not used, the white wire must be insulated. It is dangerous to touch the white wire
when the motor is powered.
*Installing this button is optional. The connection can be done differently using the
brown wire or the blue wire.The button affords the possibility to command the motor in
stepping mode (up, stop, down, stop, up, stop, down, stop..)
* Optional step by
step - Switch
brown
blue
white
green-yellow
ENGLISH

26
COMPATIBLE REMOTE CONTROLS
Down
Up
KEY TO SYMBOLS
Press button A
A
Press buttons A and B
at the same time
+
A B
GIRO
down
stop
up
A
B
C
Skipper
A
B
C
short motor rotation in one
direction
long motor rotation in other
direction
double short rotation
ENGLISH
A530058 Remote
Control with 4
independent
channels
GIRO GIRO Wall
DISPLAY
Change
channel +
Change
channel -
up
stop
down
A
B
C
UP
DOWN
LED
STOP
GIRO Plus
Display -
Activating/ Deactivating the Sun sensor
Channel selector
LED -
Check the specic
instruction book
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
LED DISPLAY
GIRO Lux
Activating the
Sun sensor
Deactivating the Sun sensor
Sun sensor is “ON”
Wind sensor
is “ON”
GIRO P-Lux DISPLAY
Change channel
Activating/ Deactivating the Sun sensor
Wind sensor
is “ON”
Sun sensor is “ON”

27
I
COMMAND SEQUENCES EXAMPLE
Most of the command sequences have three distinct steps, at the end of which the motor
indicates if the step has been concluded positively or not, by turning in different ways.This
section is provided to demonstrate the motor indications. The buttons must be pressed as
shown in the sequence, without taking more than 4 seconds between one step and the
next. If more than 4 seconds are taken, the command is not accepted and the sequence
must be repeated.
Command sequence example:
As we can see from the example, when the sequence ends positively, the motor returns to
its starting position in one long rotation. In fact, two short rotations in the same direction
correspond to one long rotation in the opposite direction.The motor returns to the starting
position even when the sequence is not completed; in this case by performing one or two
short rotations.
Example of a wrong sequence:
Step 1
Step 1
Step 1
> 4 sec repeat the
sequence
repeat the
sequence
Step 3Step 2
Step 2
> 4 sec
+
A B B B
+
A B
+
A B B
ENGLISH

28
FUNCTION OPEN/CLOSE PROGRAMMING
REMOTE CONTROL SKIPPER PLUS - SKIPPER LUX - SKIPPER P-LUX
To prevent accidental changes to the programming of the motor during the daily use of
the remote control, the possibility of programming is disabled automatically 8 hours after
sending the last sequence (A+B or B+C).
CHECKING THE STATUS OF THE FUNCTION
To change the status of the function, see the sequences “ENABLE/DISABLE
PROGRAMMING”
Proceed with programming as the instructions booklet
ENABLE PROGRAMMING
DISABLE PROGRAMMING
C
Open
or after
30 sec.
Remove and replace a battery
OPTION 2
OPTION 1
+ +B C
Tn
B
+ +
BC
Tn or after
30 sec.
B
Open
programming
Closed
programming
3 sec
+ +
A
A
A
BC
Tn or after
30 sec.
B
A
3 sec
Closed
3 sec
ENGLISH

29
FUNCTION OPEN/CLOSE PROGRAMMING
REMOTE CONTROL SKIPPER - SERIES GIRO
To prevent accidental changes to the programming of the motor during the daily use of
the remote control, the possibility of programming is disabled automatically 8 hours after
sending the last sequence (A+B or B+C).
CHECKING THE STATUS OF THE FUNCTION
To change the status of the function, see the sequences “ENABLE/DISABLE
PROGRAMMING”
Proceed with programming as the instructions booklet
ENABLE PROGRAMMING
DISABLE PROGRAMMING
ON
Open
programming
Closed
programming
....
ON
....
.... Closed
Open
ON
or after
30 sec.
or after
30 sec.
1 2 3
OPTION 1
1 2 3
1 2 3 or after
30 sec.
OPTION 2 OPTION 2
+ +
A B CB
B
C
+ +
A B C
+ +
A B C
A
B
Tn
Tn
Tn
ENGLISH
Remove a battery
and wait 5 seconds,
or press any button.
2 sec
B

30
SETTING THE FIRST REMOTE CONTROL
This operation can only be performed when the motor is new, or after a total delete of
the memory.
T1: First remote control to be set
During this step, power up only one motor at time!
T1T1 T1 (2 sec)
Every time you connect the power supply to the motor, you have 3 hours to store the
rst remote control. After this time, the ability to store the remote control is disabled.
To reset the timer of the function you have to disconnect and reconnect the power
supply to the motor.
AUTOMATIC DISABLING OF THE FIRST
REMOTE CONTROL SETTING FUNCTION
+
A B B B
ENGLISH

SETTING THE OPENING LIMIT SWITCH
31
After setting the closing position, open the awning until the necessary opening position
by pressing the “down” button. You can use the “up”/”down” buttons to precisely
set the opening position (in applications pergolas that allow this, you must press
and hold the button until the motor stops automatically to the maximum opening).
To set the opening position, hold pressed the “stop” button (around 2 sec) until the motor
performs a short “up” movement.
Tn Tn (2 sec)
Tn (2 sec)
Tn
To set the closing position, hold pressed the “stop” button (around 2 sec) until the motor
performs a short “down” movement.
Tn: Already programmed remote control
SETTING OF THE LIMIT SWITCHES
SETTING THE CLOSING LIMIT SWITCH
Tubular motors have an electronic limit switch system with an encoder. This system
ensures great reliability and precision in keeping the positions. Limit switch regulation is
performed simply with the remote control. During setting, the motor moves only as long
as the up or down button is pressed, stopping when the button is released.
At the end of setting, press either the up or down button briey to move the motor.
After setting the remote control, it’s necessary to set rst the closing position!
For cassette-awnings, hold the button pressed until the motor stops automatically on the
closing position. For open awnings, hold the button pressed and drive until the necessary
closing position.
Notes: - If the awning is completely closed, you have rstly to open it by around 20 cm.
- Because the correct rotation direction will be identied only after the closing
position is set, to close the awning, during setting the closing position, it’s
sometimes necessary to use the “down” button.
?
up
A
C
B
down
B
C
ENGLISH

32
TOTAL DELETING OF THE LIMIT SWITCHES
Tn: Already programmed remote control
Tn Tn Tn (4 sec)
DELETING THE LIMIT SWITCH POSITIONS
DELETING THE OPENING LIMIT SWITCH
To delete only the opening limit switch perform the following steps and proceed with
“SETTING THE OPENING LIMIT SWITCH”.
Tn: Already programmed remote control
Tn Tn Tn (2 sec)
DELETING THE CLOSING LIMIT SWITCH
To delete only the closing limit switch perform the following steps and proceed with
“SETTING THE CLOSING LIMIT SWITCH”.
Tn: Already programmed remote control
Tn Tn Tn (2 sec)
NB: by deleting the limit switches, the setting of the closing force is maintained (see
p. 34).
+
B C + B C
+
A B
+
B C +
B C
C
+
B C + B C + B C
ENGLISH

33
SETTING A MIDDLE POSITION
DELETING THE MIDDLE POSITION
This function allows to drive the awning to a favourite middle position. When this middle
position is memorized, just press the STOP button for 2 seconds and automatically the
motor will move the awning to this position.
To memorize the middle position, move the awning to the desired position and then hold
the STOP button down (for about 4 seconds) until the motor gives conrmation.
Tn: Already programmed remote control
If you want to delete the middle position, it can be done as described below.To change this
position, it’s also necessary to delete rst the memorized middle position.
Before deleting the middle position, the awning must go to the middle position by pressing
the STOP button for 2 second, then press the STOP button again (for about 4 seconds) until
the motor performs the conrmation movement.
Tn: Already programmed remote control
down
up
Tn (4 sec)
Tn (4 sec)Tn (2 sec)
down
up
B
BB
ENGLISH

34
This system, the only one of its kind, guarantees
that cassette-awnings remain perfectly closed,
without any danger of the canvas suffering
excessive traction. The system works in all kinds of
applications, thanks to the possibility of manually
adjusting the closing force. The motor is factory set
to a closing force of 40% of the nominal torque (e.g.:
40% of 50 Nm = 20 Nm).This force can be changed very
easily by the remote control. It can be reduced by 20%
or increased up to 70%, depending on the desired result.
CLOSING FORCE ADJUSTMENT
2 sec
70 %
40 %
20 %
Tn
+
B C
A A
C
B
MAXIMUM CLOSING FORCE ADJUSTMENT (100%)
- only for motors from 32 Nm -
A close attention on activating this function is recommended, excessive closing force may
damage the awning.
By activating this function the motor will apply its maximum nominal torque, (e.g. 100%
of 50 Nm = 50 Nm).
Tn
+
B C
A
2 sec
+
A C
Tn: Already programmed remote control
ENGLISH

35
SETTING OF ADDITIONAL REMOTE CONTROLS
REMOTE CONTROL MEMORY CLEARING
Up to 15 remote controls can be set, including the light/wind sensor.
Tn: Already programmed remote control
Tx: Additional remote control
It is possible to delete singly all the memorized remote controls. When the last one is
deleted the motor initial condition is restored.The same applies to the single channels of
a multichannel remote control: just select the channel to cancel.
Tn: Remote control to be cleared
Tn
Tn
Tn
Tn
Tx (2 sec)
Tn (2 sec)
+
A B BB
+
A B B
A
ENGLISH

36
2) WITH THE WHITE WIRE
Do this operation only in case of emergency, if all remote controls are no longer operating.
To delete the memory we have to access the white wire of the motor.
The sequence of this operation is the following:
1) Disconnect the power supply from the motor, via the main switch for example.
2) Connect the white motor wire to the brown wire (phase) or to the blue wire (neutral).
3) Connect the power supply to the motor, which rotates briey in one direction.
4) Disconnect the power supply from the motor for at least 4 seconds.
5) Connect the power supply to the motor which performs one brief rotation in one
direction after around 4 seconds and then a longer one in the opposite direction.
6) Disconnect the power supply from the motor.
7) Separate the white wire from the brow/blue wire. Insulate the white wire, in an
appropriate way, before reconnecting the power supply.
At this point it is possible to proceed with the setting of the rst remote control.
FULL MEMORY CLEARING
The full memory clearing can be performed in two ways:
1) WITH THE REMOTE CONTROL
Tn: Already programmed remote control
TnTn Tn (4 sec)
This full memory clearing does not delete the setting of the limit switch.
W
H
I
T
E
W
H
I
T
E
+
A B + A B
B
ENGLISH

37
SPECIAL FUNCTIONS
ADDITIONAL MIDDLE POSITION
The additional middle position is useful to open the awning automatically through the
WindTec Lux sensor and to bring it to a middle position when the light of the environment
exceeds the threshold set.This additional middle position can be used only in combination
with the light automatism of the WindTec Lux sensor.
The awning cannot be brought to this position with the remote control.
However, there is the possibility to program the current middle position using the B button
(2 sec) command.If the additional middle position is not memorized, the light automatism
of the WindTec Lux sensor (when enabled) opens the awning completely. When the
WindTec Lux (Set button) sensor is tested, the movements of the motor do not take the
additional middle position into consideration: the awning always stops in the half-way
position and opens completely if the light exceeds the threshold value.
SETTING THE ADDITIONAL MIDDLE POSITION
After saving the limit switches, carry out the following command sequence:
Tn: Already programmed remote control
Tn Tn Tn (2 sec)
Starting from this moment, the motor moves in the “DEAD MAN” mode. This makes it
possible to regulate the additional middle position in a precise way.
Carry out the following operations:
• Bring the awning to the desired open position.
• Press the B button of the remote control for about 2 seconds, until the motor gives a
conrmation signal.
Starting from this moment, when the WindTec Lux commands the opening of the awning
through the light automatism (if this is enabled), the awning will be brought to the
additional middle position.
+
B C
B B
Tn (2 sec)
down
up
B
ENGLISH

38
CHANGING THE ADDITIONAL MIDDLE POSITION
To change the additional middle position repest the procedure described in the previous
section.
DELETING THE ADDITIONAL MIDDLE POSITION
Carry out the following command sequence in order to cancel the additional middle
position:
Tn: Already programmed remote control
Tn Tn Tn (2 sec)
SHORT-TERM SETTING OF A REMOTE CONTROL
This function makes it possible to store a remote control temporarily, for example, with the
purpose of setting the limit switches during assembly in the factory. A later nal saving
of the remote control will be possible using the appropriate command sequence (see:
“SETTING THE FIRST REMOTE CONTROL”).The operations described below can be carried
out only when the motor has just come out of the factory or after a full memory clearing
(see: “FULL MEMORY CLEARING”). The motor makes the following operations possible
only within the time limits described in order to make sure that the short-term setting is
used only in the installation or factory setting phase and not during daily use.
Power up the motor, make sure that no other motors having an empty memory are
powered up in the same operating range.
Within 30 seconds after start, press the B and C buttons simultaneously until the motor
gives a conrmation signal.
The remote control will remain stored for 5 minutes, while the motor is powered up.
After 5 minutes or when the motor has its power cut off, the remote control will be
cancelled.
T1: First remote control to be set
T1
+
B C
B
A
+
BC
+
B C
ENGLISH

39
SETTING THE A530058 POCKET REMOTE CONTROL
NB: The new pocket remote control can be set only after programming of a previous
remote control as the traditional Cherubini remote controls (Skipper or Giro - 3 buttons
Up-Down-Stop remote control).
HOW TO PROCEED TO SET THE BUTTON ON THE POCKET REMOTE CONTROL
Tn: Already programmed remote control
Tx: Pocket remote control to be set
Tn
Tn
Tn Tx (2 sec)
1
3 4
2
Tx (2 sec)
1
3 4
2
After to have pressed for minimal 2 seconds one of the 4 buttons on the pocket remote
control, this one will be memorized on the step-by-step mode (UP-STOP-DOWN-STOP).
The following buttons will be not memorized and have to be done with previous described
sequence, and could be used to move additional motors.
DELETING ONE BUTTON ON THE POCKET REMOTE CONTROL
The buttons saved may be deleted individually according to the following sequence:
Tn: Already programmed remote control
Tx: Pocket remote control with button to be deleted
Tn
To conrm the operation the motor will do a short shunt and the button, which has to be
pressed for minimal 2 second, will be deleted.
+
A B
+
B C
+
A B
A
ENGLISH

40
FABRIC TIGHTENING FUNCTION
By programming this function, the motor after reaching the outer limit, automatically
performs a short backwards turn to tighten the fabric. Specially designed for pergolas and
horizontal awnings.
N.B: The programming of this option can be made only after setting the limit switches.
STARTING THE SETTING PROCEDURE:
Tn: Already programmed remote control
Tn
Tn
Tn
Tn
Tn (2 sec)
Tn (2 sec)
After adjusting and conrming the tensioning position, the motor drives to the open
position and returns to the new tensioning position which has just been conrmed. From
this moment, each time the motor reaches the open position, automatically it will turn
back to the “tensioning position”.
DELETING THE TENSIONING POSITION
Tn: Already programmed remote control
This rst process brings the awning to the open position and sets the motor into “DEAD
MAN” operating mode. Thereafter, the fabric tensioning position can be adjusted
accurately.
ADJUSTMENT AND CONFIRMATION OF THE TENSIONING POSITION
Tn: Already programmed remote control
Tn Tn (2 sec)
conrmingadjusting
+
B C + B C
B
B
A
+
B C + B C
A
ENGLISH