CHERUBINI Garda User manual

ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
Garda
Roll
Roll Easy
Micro
Micro Easy
I
GB
D
F
E
MOTORI TUBOLARI
TUBULAR MOTORS
ROHRMOTOREN
MOTEURS TUBULAIRES
MOTORES TUBULARES

- To prevent any danger or malfunction, the size of electrical control components
connected to the motor must be compatible with the electrical features of the motor.
- Means for disconnection must be incorporated in the xed wiring in accordance with
the national installation standards.
- The selectors inverting the direction of rotation of the motor must be provided with
mechanical interloc king.
- Invert the brown and the black conductor to change the direction of rotation.
- NEVER connect two or more motors to the same selector (parallel connection). If you
couple two motors, use multi-poles selectors only.
- NEVER connect two or more selectors to the same motor.
- For outdoor use,provide the appliance with a supply cable
with designation H05RN-F containing
at least 2% of carbon.
ELECTRICAL CONNECTIONS
7
TRANSLATION OF THE ORIGINAL INSTRUCTIONS

I
8
1- brown
2- black
3- blue
4- yellow-green
GB

9
HOW TO PREPARE THE MOTOR
NB: If you use tubes with a round form, the driving pulley must be xed to the tube, and
the installation is to be paid by the person who installs the system. For other tube sections
the tting is optional, but strongly recommended.
STOP RING NUT ADAPTOR
DRIVING PULLEY
STOP RING NUT
1. Insert the adaptor in the stop ring nut
mating the groove with the reference notch
and push till they touch.
2. Fix the driving pulley on the motor pin
until the stop pin clicks.
3. Insert the motor fully in the rolling tube.
GB
1
2
3

B
A
STOP RING NUT
ADJUSTING
SCREWS
CHERUBINI S.p.A. declares that the product is in conformity with the relevant
Union harmonisation legislation:
Directive 2014/35/EU
Directive 2014/30/EU
Directive 2011/65/EU
The full text of the EU declaration of conformity is available upon request at the
following website: www.cherubini.it.
EU DECLARATION OF CONFORMITY
ADJUSTEMENT OF THE LIMIT SWITCHES
These tubular motors are provided with a system of electromechanical limit switches that
stops the feed when the awning or the rolling shutter get to the maximum opening or
closing limits. To adjust these limits and adapt them to any need, simply screw or unscrew
the two adjusting screws on the motor head. The limits of the limit switches are preset at
about three turns of the roller.
10
1. To decide which adjusting screw to x, simply watch the direction
of rotation of the stop ring nut: if the stop ring nut pulled by the
roller goes in direction A, use the adjusting screw A to set the limit
switch in that direction. If it goes to the opposite direction (B), use
the adjusting screw B.
2. Start up the awning or the rolling shutter in the direction in
which you wish to set the rst limit switch.After a few turns the
motor will stop on the preset stop.
3. Screw the adjusting screw suited to the direction (see point
1.) in direction “+” till it gets to the chosen position.
4. Invert the engine sense of direction and set the second
limit switch.
GB

Rev: 16 04/2020 - Cod: A4516_6190
CHERUBINI Deutschland GmbH
Siemensstrasse, 40 - 53121 Bonn - Deutschland
Tel. [phone] / 35 | Fax [phone]
[e-mail] | www.cherubini-group.de
CHERUBINI France S.a.r.l.
ZI Du Mas Barbet
165 Impasse Ampère
30600 Vauvert -France
Tél. [phone] | Fax [phone]
[e-mail] | www.cherubini.fr
CHERUBINI Iberia S.L.
Avda. Unión Europea 11-H
Apdo. 283 - P. I. El Castillo
03630 Sax Alicante - Spain
Tel. [phone] | Fax [phone]
[e-mail] | www.cherubini.es
CHERUBINI S.p.A.
Via Adige 55
25081 Bedizzole (BS) - Italy
Tel. [phone] | Fax [phone]
[e-mail] | www.cherubini.it