CHERUBINI Ocean RX User manual

ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
Ocean RX
I
GB
D
F
E
MOTORE TUBOLARE RADIO CON
REGOLAZIONE MANUALE DEL FINECORSA
E MANOVRA DI SOCCORSO
RADIO TUBOLAR MOTOR WITH
MECHANICAL LIMIT SWITCH ADJUSTMENT
AND MANUAL OVERRIDE DEVICE
MOTOR MIT INTEGRIERTEM FUNKEMPFÄNGER
MECHANISCHER ENDABSCHALTUNG
UND NHK-NOTHANDKURBELGETRIEBE
MOTEUR TUBULAIRE RADIO AVEC
RÉGLAGE MÉCANIQUE DU FIN DE COURSE
MANOEUVRE DE SECOURS
MOTOR RADIO CON REGULACIÓN MECÁNICA
DE LOS FINES DE CARRERA
MANIOBRA DE EMERGENCIA

21
Table of contents:
How to prepare the motor ...................................................................................... p. 22
Electrical connections ............................................................................................. p. 23
Compatible remote controls ................................................................................... p. 24
Key to symbols ....................................................................................................... p. 24
Command sequences example ............................................................................... p. 25
Function open/close programming remote control ............................................. p. 26-27
Setting the rst remote control .............................................................................. p. 28
Automatic disabling of the rst remote control setting function ............................ p. 28
Adjustement of the limit switches .......................................................................... p. 28
Setting the rotation direction of the motor ............................................................. p. 29
Setting of additional remote controls ..................................................................... p. 30
Remote control memory clearing ........................................................................... p. 30
Restore the factory mode ....................................................................................... p. 30
Full memory clearing .............................................................................................. p. 31
Adjustment of the limits switches on torque .......................................................... p. 32
Closing force adjustment ....................................................................................... p. 32
Behavior of motors on limit switch and obstacle detection ................................... p. 32
Compatible devices
Mistral sensor ......................................................................................................... p. 33
Rugiada (TX rain-sensor) ........................................................................................ p. 34
Anemometers ......................................................................................................... p. 34
Special functions
Short-term setting of a remote control ................................................................... p. 36
Setting the A530058 pocket remote control ........................................................... p. 36
Electric wiring to motor command for UP-DOWN mode
(2 independent UP-DOWN buttons) ....................................................................... p. 37
Command management from white wire ............................................................... p. 38
EU Declaration of conformity ................................................................................. p. 93
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
ENGLISH

22
ENGLISH
HOW TO PREPARE THE MOTOR
NB: If you use tubes with a round form, the driving pulley must be xed to the tube, and
the installation is to be paid by the person who installs the system. For other tube sections
the xing is optional but strongly recommended.
STOP RING NUT ADAPTOR
DRIVING PULLEY
STOP RING NUT
1
2
3
1. Insert the adaptor in the stop ring nut
mating the groove with the reference notch
and push till they touch.
2. Fix the driving pulley on the motor pin
until the stop pin clicks.
3. Insert the motor fully in the rolling tube.

23
ELECTRICAL CONNECTIONS
- In order to prevent dangerous situations or malfunctioning, the electrical command
elements wired to the motor must be sized according to the motor’s electrical features.
- Means for disconnection must be incorporated in the xed wiring in accordance with
the national installation standards.
- For outdoor use, provide the appliance with a supply cable with designation H05RN-F
containing at least 2% of carbon.
- If not used, the white wire must be insulated. It is dangerous to touch the white wire
when the motor is powered.
*Installing this button is optional. The connection can be done
differently using the brown wire or the blue wire. The button
affords the possibility to command the motor in stepping mode
(up, stop, down, stop, up, stop, down, stop..)
* Optional step by
step - Switch
brown
blue
white
green-yellow
ENGLISH

Up
Stop
Down
SEL (POP Lux)
Activating/ Deactivating
the Sun sensor
Up
Stop
Down
SEL (POP P-Lux)
Activating/ Deactivating
the Sun sensor
24
ENGLISH
COMPATIBLE REMOTE CONTROLS
KEY TO SYMBOLS
LED
A530058 Remote
Control with 4
independent
channels
DISPLAY
GIRO POP
A
B
C
down
stop
up
Skipper
A
B
C
down
stop
up
A
B
C
Display -
Activating/ Deactivating the Sun sensor
Channel selector
LED -
Check the specic
instruction book
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
Skipper
GIRO GIRO Wall
DISPLAY
Change
channel +
Change
channel -
up
stop
down
A
B
C
UP
DOWN
LED
STOP
GIRO Plus LED DISPLAY
GIRO Lux
Activating the
Sun sensor
Deactivating the Sun sensor
Sun sensor is “ON”
Wind sensor
is “ON”
GIRO P-Lux DISPLAY
Change channel
Activating/ Deactivating the Sun sensor
Wind sensor
is “ON”
Sun sensor is “ON”
POP
POP Lux
Sun/wind sensor
(POP Lux)
POP Plus
POP P-Lux
Sun/wind sensor
(POP P-Lux)

25
I
ENGLISH
I
Down
Up
COMMAND SEQUENCES EXAMPLE
Most of the command sequences have three distinct steps, at the end of which the
motor indicates if the step has been concluded positively or not, by turning in different
ways. This section is provided to demonstrate the motor indications. The buttons must
be pressed as shown in the sequence, without taking more than 4 seconds between one
step and the next. If more than 4 seconds are taken, the command is not accepted and
the sequence must be repeated. Command sequence example:
As we can see from the example, when the sequence ends positively, the motor returns to
its starting position in one long rotation. In fact, two short rotations in the same direction
correspond to one long rotation in the opposite direction.The motor returns to the starting
position even when the sequence is not completed; in this case by performing one or two
short rotations. Example of a wrong sequence:
+
A B B B
Step 1
Step 1
> 4 sec repeat the
sequence
repeat the
sequence
Step 2
> 4 sec
+
A B
+
A B B
Step 1 Step 3Step 2
KEY TO SYMBOLS
Press button A
A
Press buttons A and B
at the same time
+
A B
short motor rotation
in one direction
long motor rotation
in other direction
double short
rotation
Down
Up

26
ENGLISH
FUNCTION OPEN/CLOSE PROGRAMMING
REMOTE CONTROL SKIPPER PLUS - SKIPPER LUX - SKIPPER P-LUX
REMOTE CONTROL POP PLUS - POP LUX - POP P-LUX
To prevent accidental changes to the programming of the motor during the daily use of
the remote control, the possibility of programming is disabled automatically 8 hours after
sending the last sequence (A+B or B+C).
CHECKING THE STATUS OF THE FUNCTION
To change the status of the function, see the sequences “ENABLE/DISABLE
PROGRAMMING”.
Proceed with programming as the instructions booklet.
ENABLE PROGRAMMING
DISABLE PROGRAMMING
Open
or after
30 sec.
Remove and replace
a battery
OPTION 2
OPTION 1
or after
30 sec.
Open
programming
Closed
programming
3 sec
or after
30 sec.
3 sec
Closed
3 sec
OPTION 2
+ +
A B C
Tn
+ +
A B C
Tn
+ +
A B C
Tn
B
B
B
C
A

27
ENGLISH
FUNCTION OPEN/CLOSE PROGRAMMING
REMOTE CONTROL SKIPPER - SKIPPER WALL - SERIES GIRO
To prevent accidental changes to the programming of the motor during the daily use of
the remote control, the possibility of programming is disabled automatically 8 hours after
sending the last sequence (A+B or B+C).
CHECKING THE STATUS OF THE FUNCTION
To change the status of the function, see the sequences “ENABLE/DISABLE
PROGRAMMING”.
Proceed with programming as the instructions booklet.
ENABLE PROGRAMMING
DISABLE PROGRAMMING
ON
Open
programming
Closed
programming
....
ON
....
.... Closed
Open
ON
or after
30 sec.
or after
30 sec.
1 2 3
OPTION 1
1 2 3
1 2 3 or after
30 sec.
OPTION 2 OPTION 2
+ +
A B CB
B
C
+ +
A B C
+ +
A B C
A
B
Tn
Tn
Tn
Remove one battery and wait minimum 5 seconds or press any button.
2 sec
B
OPTION 2

1. To decide which adjusting screw to x, simply watch the direction of rotation of the stop
ring nut: if the stop ring nut pulled by the roller goes in direction A, use the adjusting
screw A to set the limit switch in that direction. If it goes to the opposite direction (B),
use the adjusting screw B.
2. Start up the awning or the rolling shutter in the direction in which you wish to set the
rst limit switch. After a few turns the motor will stop on the preset stop.
3. Screw the adjusting
screw suited to the
direction (see point
1.) in direction “+” till
it gets to the chosen
position.
4. Invert the engine sense
of direction and set the
second limit switch.
SETTING THE FIRST REMOTE CONTROL
This operation can only be performed when the motor is new, or after a total delete of
the memory.
T1: First remote control to be set
During this step, power up only one motor at time!
T1T1 T1 (2 sec)
Every time you connect the power supply to the motor, you have 3 hours to store the
rst remote control. After this time, the ability to store the remote control is disabled.
To reset the timer of the function you have to disconnect and reconnect the power
supply to the motor.
AUTOMATIC DISABLING OF THE FIRST
REMOTE CONTROL SETTING FUNCTION
+
A B B B
NB: Until the remote control has been memorised, the wired control of the motor
will operate in “dead-man” mode.
ADJUSTEMENT OF THE LIMIT SWITCHES
ENGLISH

29
SETTING THE ROTATION DIRECTION OF THE MOTOR
The operation can be performed via remote control or using the white wire.
Every time you perform one of the two sequences below you reverse the output direction
of the motor.
From the remote control:
Tn: Already programmed remote control
Tn
+
A B
Tn
C
Tn (4 sec)
+
A C
From the wired control:
The sequence of this operation is the following:
1) Disconnect the power supply from the motor, via the main switch for example.
2) Connect the white motor wire to the brown wire (phase) or to the blue wire (neutral).
3) Connect the power supply to the motor, which rotates briey in one direction.
4) Disconnect the power supply from the motor for at least 4 seconds.
5) Connect the motor to the power supply, after about 2 seconds the motor performs a
short rotation up or down. Within 3 seconds disconnect the power supply, for example
using the main switch.
6) Disconnect the white wire from the motor.
max 3 sec2 sec
W
H
I
T
E
W
H
I
T
E
ENGLISH

30
SETTING OF ADDITIONAL REMOTE CONTROLS
REMOTE CONTROL MEMORY CLEARING
Up to 15 remote controls can be set.
Tn: Already programmed remote control
Tx: Additional remote control
It is possible to delete singly all the memorized remote controls. When the last one is
deleted the motor initial condition is restored.The same applies to the single channels of
a multichannel remote control: just select the channel to cancel.
Tn: Remote control to be cleared
Tn
Tn
Tn
Tn
Tx (2 sec)
Tn (2 sec)
+
A B BB
+
A B B
A
RESTORE THE FACTORY MODE
Tn: Already programmed remote control
The following settings are now in factory mode: direction of rotation, timeout and white
wire control mode.
TnTn Tn (4 sec)
+
B C + B C + B C
ENGLISH

31
2 sec 6 sec
W
H
I
T
E
W
H
I
T
E
FULL MEMORY CLEARING
The full memory clearing can be performed in two ways:
1) WITH THE REMOTE CONTROL
Tn: Already programmed remote control
TnTn Tn (4 sec)
2) WITH THE WHITE WIRE
Do this operation only in case of emergency, if all remote controls are no longer operating.
To delete the memory we have to access the white wire of the motor.
The sequence of this operation is the following:
1) Disconnect the power supply from the motor, via the main switch for example.
2) Connect the white motor wire to the brown wire (phase) or to the blue wire (neutral).
3) Connect the power supply to the motor, which rotates briey in one direction.
4) Disconnect the power supply from the motor for at least 4 seconds.
5) Connect the motor to the power supply, after about 2 seconds the motor performs a
short rotation up or down. After about 6 seconds the motor performs a long rotation
in the opposite direction.
6) Disconnect the power supply from the motor.
7) Separate the white wire from the brow/blue wire. Insulate the white wire, in an
appropriate way, before reconnecting the power supply.
At this point it is possible to proceed with the setting of the rst remote control.
+
A B + A B
B
ENGLISH

32
ENGLISH
LIMIT SWITCH SETTING ON A CASSETTE AWNING (closing on torque)
On a cassette awning is possible to set the upper limit on torque closing. Connect the
motor, set the remote control and move the motor by moving the adjustment screws in
+direction as close as possible to the upper limit switch and stop the motor. Now move
again the adjustment screws for three (3) turns beyond the upper limit.
ADJUSTMENT OF THE LIMITS SWITCHES ON TORQUE
CLOSING FORCE ADJUSTMENT
This system ensures, when used it with box awnings,
that the awning remains completely closed, without
the awning fabric undergoing excessive stress from
pulling.
The motor has been set in the factory to a
predetermined closing force setting, equal to 40%
of the rated torque. With the remote control it is
possible to change this setting, reducing it to 20%, or
increasing it to 70%, depending on the desired result.
70%
40%
20%
2 sec
+
B C
AA
C
B
BEHAVIOR OF MOTORS ON LIMIT SWITCH AND
OBSTACLE DETECTION
UPPER LIMIT SWITCH IN
TORQUE CLOSING (Cassette
awings or rolling shutter)
OBSTACLE DETECTION IN
UP MOVEMENT
Ocean RX The motor goes every time to
the limit-stop and does not a
reverse movement.
The motor stops and does not
a reverse movement.

33
COMPATIBLE DEVICES
I
For the complete description of the functions of this device see the instruction booklet
that came in the box.
It detects movements caused by the wind on the awning arms.
MISTRAL SENSOR
SETTING THE SENSOR
DELETING THE SENSOR
SELECTOR
LED
SET BUTTON
0
To associate the sensor to the control unit, a remote control must be already memorized.
Set the selector to the 0 position and then perform this sequence:
To delete the sensor from the control unit, an already programmed remote control must
be used. Set the selector to the 0 position; if active wait for the sensor to go off and then
perform this sequence:
MISTRAL- Ref. A520012
2 sec
set
+
A B B
2 sec
set
+
A B
A
ENGLISH

34
ANEMOMETERS
WINDTEC - Ref. A520007 WINDTEC LUX - Ref. A520008
Sun-sensor
tuning
Set button
Wind-speed
tuning
set
SETTING
To associate the sensor to the control unit, a remote control must be already memorised.
The setting sequence is the following:
DELETING
To delete the sensor from the control unit, an already programmed remote control must
be used. The deleting sequence is the following:
For the complete description of the functions of these devices see the instruction booklet
that came in the box.
RUGIADA (TX RAIN-SENSOR)
Power Supply 230 Vac
Sensor element
Set button
set
Rugiada - Ref. A520016
2 sec
set
+
A B B
2 sec
set
+
A B
A
ENGLISH

35
TEST MODE (WINDTEC/WINDTEC LUX)
This function is useful to check proper radio communications and to perform the wind
and sun function test.
To activate the TEST function, hold the SET button down for around 2 seconds, until
the awning opens for 10 seconds and closes briey to conrm that the test has been
activated. The Test function lasts for 3 minutes, during which the wind and sunlight
threshold settings can be checked, without waiting for activation times. After 3 minutes,
the WindTec sensor returns to normal operational mode.
WIND FUNCTION TEST (WINDTEC, WINDTEC LUX)
To avoid errors during the wind function test, it is suggested that the sunlight function
be deactivated. By spinning the anemometer ns, when the speed detected by the sensor
exceeds the threshold set, the motor commands the closing of the awnings.
SUN FUNCTION TEST (WINDTEC LUX)
Make sure that the sunlight function is on. When the sensor detects a change in the
sunlight intensity, it opens the awning if the sunlight intensity goes above the threshold
set, or it closes the awning if the light intensity goes below the threshold set. It is possible
to repeat this test several times, so as to nd the desired adjustment levels precisely.
2 sec
set
ENABLE / DISABLE THE SUN SENSOR
(WindTec Lux)
To enable (automatically) or disable (manually) the sun sensor refer to the instruction
manual provided with the sensor or the remote control you want to use.
ENGLISH

36
SHORT-TERM SETTING OF A REMOTE CONTROL
This function makes it possible to store a remote control temporarily, for example, with
the purpose of setting the limit switches during assembly in the factory. A later nal
saving of the remote control will be possible using the appropriate command sequence
(see: “SETTING THE FIRST REMOTE CONTROL”). The operations described below can be
carried out only when the motor has just come out of the factory or after a full memory
clearing (see: “FULL MEMORY CLEARING”). The motor makes the following operations
possible only within the time limits described in order to make sure that the short-term
setting is used only in the installation or factory setting phase and not during daily use.
Power up the motor, make sure that no other motors having an empty memory are
powered up in the same operating range.
Within 30 seconds after start, press the B and C buttons simultaneously until the
motor gives a conrmation signal.
The remote control will remain stored for 5 minutes, while the motor is powered up.
After 5 minutes or when the motor has its power cut off, the remote control will be
cancelled.
T1: First remote control to be set
T1
+
BC
+
B C
SPECIAL FUNCTIONS
SETTING THE A530058 POCKET REMOTE CONTROL
NB: The new pocket remote control can be set only after programming of a previous
remote control as the traditional Cherubini remote controls (Skipper, Giro or POP - 3
buttons Up-Down-Stop remote control).
HOW TO PROCEED TO SET THE BUTTON ON THE POCKET REMOTE CONTROL
Tn: Already programmed remote control
Tx: Pocket remote control to be set
Tn Tn Tx (2 sec)
1
3 4
2
+
A B
+
B C
ENGLISH

37
Tn Tx (2 sec)
1
3 4
2
After to have pressed for minimal 2 seconds one of the 4 buttons on the pocket remote
control, this one will be memorized on the step-by-step mode (UP-STOP-DOWN-STOP).
The following buttons will be not memorized and have to be done with previous described
sequence, and could be used to move additional motors.
DELETING ONE BUTTON ON THE POCKET REMOTE CONTROL
The buttons saved may be deleted individually according to the following sequence:
Tn: Already programmed remote control
Tx: Pocket remote control with button to be deleted
Tn
To conrm the operation the motor will do a short shunt and the button, which has to be
pressed for minimal 2 second, will be deleted.
+
A B
A
ELECTRIC WIRING TO MOTOR COMMAND FOR UP-DOWN MODE
(2 independent UP-DOWN buttons)
To connect the switch, use only kind of switches with mechanical or electrical interlock, to
prevent to press both buttons at same time.
The motor automatically recognizes the switch-type (with 1 or 2 buttons) and sets the
proper operational mode.
Switch with mechanical
or electrical interlocking
ENGLISH
1 - brown
2 - white
3 - blue
4 - yellow-green

38
COMMAND MANAGEMENT FROM WHITE WIRE
UP-STOP-DOWN-STOP / UP-DOWN / UP-DOWN “DEAD MAN”
NB: The default function provided in the motors leaving the factory is UP-STOP-DOWN-
STOP for singular UP/DOWN button switch. (Not for the switch with two independent
UP-DOWN buttons!)
PROCEDURE TO CHANGE THE CONTROL MODE:
Tn: Already programmed remote control
The possible settings are 3 and are available in the following order:
- UP-STOP-DOWN-STOP (factory setting)
- UP-DOWN (for 2 independent buttons)
- UP-DOWN “DEAD MAN” (for 2 independent buttons)
To switch from one setting to the following, perform the sequence as many times as
necessary to reach the desired setting.
Mode UP-STOP-DOWN-STOP:
Mode UP-DOWN:
Mode UP-DOWN “DEAD MAN”:
Tn Tn (2 sec)Tn
+
B C
B
C
B C
B C
B C
B
B
B
C
C
C
ENGLISH