CHERUBINI Tronic RX User manual

TRONIC RX
ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
I
GB
D
F
E
PROGRAMMAZIONE FILARE
WIRE PROGRAMMING
DRAHTGEBUNDENE PROGRAMMIERUNG
PROGRAMMATION FILAIRE
PROGRAMACIÓN DESDE EL PULSADOR

Table of contents
Important safety instructions ............................................................................ p. 17-18
How to prepare the motor ...................................................................................... p. 19
Electrical connections ............................................................................................. p. 20
Choice of the programming modes................................................................... p. 21
Activation/deactivation of the remote control function .......................................... p. 21
Key to symbols ....................................................................................................... p. 22
Command sequences example ............................................................................... p. 22
Motor programming from the white wire .............................................................. p. 23
Note for operation from the button switch ............................................................ p. 23
Adjustment of the limit switches ............................................................................ p. 23
Setting in mode 1 (manual) .................................................................................. p. 23
Example 1: Setting rst the opening position ...................................................... p. 24
Example 2: Setting rst the closing position ........................................................ p. 25
Mode 2: limit switch setting (semi-automatic) ..................................................... p. 26
Setting/deleting a middle position .......................................................................... p. 27
Closing force adjustment ........................................................................................ p. 28
Activating/deactivating the super-sensitivity function (only for Ø 35 motors) ........ p. 29
Deleting the opening and closing limit switch ........................................................ p. 29
16
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
ENGLISH
CHERUBINI S.p.A. declares that the product is in conformity with the relevant Union
harmonisation legislation:
Directive 2014/53/EU, Directive 2011/65/EU.
The full text of the EU declaration of conformity is available upon request at the
following website: www.cherubini.it.
EU DECLARATION OF CONFORMITY

17
ENGLISH
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
WARNING: Important safety instructions
It is important for everyone’s safety to follow these instructions in full.
Keep these instructions for future reference.
- The tubular motors have been designed for the automation of solar protections like roller
shutters, screen, awnings, vertical awnings a.s.o. Any other use is improper. Special applications
shall be submitted to Cherubini S.p.A.’s analysis and approval.
Useful suggestions on motor choice are available on the website www.cherubini.it.
- Only professional technicians must perform installation, complying with all safety instructions,
especially those regarding electrical connections.
- This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
- Do not allow children to play with xed control devices. Keep remote controls out of the reach of
children.
- Shutters: watch the moving shutter and keep people away until the shutter is completely closed;
take care when operating the manual release with shutter open since it may fall rapidly due to
weak or broken springs.
- Awnings: Do not operate the awning when maintenance, such as window cleaning, is being
carried out in the vicinity.
- Disconnect the automatically controlled shutter/awning from the supply when maintenance,
such as window cleaning, is being carried out in the vicinity.
- Check the system frequently in order to detect any out-of-balance condition or signs of wear. Do
not use the motorized unit if it needs repair or adjustment.
- The supply cord of this motor can be replaced only by the same type of cable supplied by
Cherubini S.p.A.
- The acoustic emission level of Cherubini S.p.A. motors is lower than 70dBA: LpA < 70dB(A).
- The choice of the motor, based on its application requirements, shall be compatible with the data
written on the motor label. The trade name of the product is printed on the label.
Every motor model is identied by a part number on the packaging label. The part number is
described in the motor catalog available on the website www.cherubini.it.
WARNING: the motor shall be disconnected from its power source during cleaning,
maintenance and when replacing parts.
- Only professional technicians must perform maintenance and repairs.
- If the supply cord is damaged please call the assistance centre or qualied technical
staff, in order to avoid any hazard.
- The tubular motor is designed to work non-stop for a maximum of 4 minutes.
- Do not squash, crush, drop or wet the tubular motor with any kind of liquid; do not pierce and
do not apply any screw along the tubular section.
- The guarantee does not cover any damage caused by misuse, straining, tampering or incorrect
connections.
WARNINGS FOR USER

18
ENGLISH
- The choice of the motor, in its use application, must be compatible with the rating marked on
the motor itself. For further technical information, refer to product data sheet on the website
www.cherubini.it or contact your local Cherubini representative (see the last page of this manual
for the addresses).
- The mass and the dimension of the driven part shall be compatible with the rated torque and
related operating time. Nominal torque and operating time are given on the motor rating label,
in Nm and min. units respectively.
- The minimum diameter of the tube on which the motor can be installed is related to its
proper external diameter. The values to be considered are the rst two part number digits (e.g.
AMP35xxxxxx, AME45xxxxxx, AME58xxxxxx). The tube must have a minimum diameter not
lower than the following values: 40 mm (for motors identied with 35), 50 mm (45), 70 mm (58)
- For outdoor exposure provide to protect the supply cord by inserting it into a cable duct. motor
with 60245 IEC 53 (H05RR-F) or 60245 IEC 57 (H05RN-F) designated supply cord shall be installed.
- Before installing the drive motor, remove any unnecessary cable and disconnect any equipment
not required for the working of the motor itself.
- Before each maintenance intervention, installation or window cleaning switch off the motor
power supply.
- The actuating member of a biased-off switch is to be located within direct sight of the driven part
but away from moving parts. It is to be installed at a minimum height of 1.5 m and not accessible
to the public.
- If the motor is tted with the emergency manual operation device, the length of the rod must
ensure that the crank is at a height below 1.8 metres.
- Fixed controls have to be clearly visible after installation.
- If the motor is used to move sun awnings, keep a safety horizontal distance of at least 40 cm
between the fully opened awning and any permanent object.
- If the supply cord is damaged, it must be replaced by Cherubini Service in order to prevent any
risk.
- Connection devices, supports and adaptors are not supplied with our motors but separately. For
use and choice consult the Cherubini “Tubular motors” catalogue (see www.cherubini.it).
- During connection follow the instructions thoroughly. If you have any doubt, NEVER act at
random but consult competent technicians.
- The guarantee does not cover any damage caused by misuse, straining, tampering or incorrect
connections.
WARNINGS FOR INSTALLER
WARNING: Important safety instructions.
Follow all instructions, since incorrect installation can lead to severe injury.
NO NO NO NO NO

19
I
HOW TO PREPARE THE MOTOR
NB: If you use tubes with a round form, the driving pulley must be xed to the tube, and
the installation is to be paid by the person who installs the system. For other tube sections
the tting is optional, but strongly recommended.
1. Insert the adaptor in the nut mating the
groove with the reference notch and push
till they touch.
2. Fix the driving pulley on the motor pin
until the stop pin clicks.
3. Insert the motor fully in the rolling tube.
STOP RING NUT ADAPTOR
DRIVING PULLEY
STOP RING NUT
1
2
3
ENGLISH

I
20
Switch with mechanical
or electrical interlocking
1- brown
2- white
3- blue
4- green-yellow
ELECTRICAL CONNECTIONS
- In order to prevent dangerous situations or malfunctioning, the electrical command
elements wired to the motor must be sized according to the motor’s electrical features.
- Means for disconnection must be incorporated in the xed wiring in accordance with
the national installation standards.
- For outdoor use, provide the appliance with a supply cable with designation H05RN-F
containing at least 2% of carbon.
- If not used, the white wire must be insulated. It is dangerous to touch the white wire
when the motor is powered.
ENGLISH
NOTE FOR
OPERATION FROM
THE BUTTON SWITCH
- vd. pag. 23-

CHOICE OF THE PROGRAMMING MODES:
RADIO - WHITE WIRE - WHITE WIRE with the radio function active
The Tronic RX motor may be programmed using 3 modes:
- RADIO PROGRAMMING: Once the programming has been completed the motor
enables use either by white-wire, by radio, or using both modes (radio/wire).
- WHITE WIRE PROGRAMMING:
· After the adjustment of the limit switches using the white wire, programming remains
active for 5 min. After 5 min have elapsed, the motor must be disconnected from its
power supply and then reconnected in order to reprogram the system.
· If the limit switches are set using the whitewire without programming a remote
control, the radio function is automatically deactivated for programming and for later
use. To reset the radio function, the activation sequence found on this page must be
performed within 5 min from the adjustment of the limit switches (or after having
disconnected and then reconnected the motor from its power supply).
· Once the programming has been completed the motor enables only the use of the
white wire, unless the radio function is reactivated.
- WHITE WIRE PROGRAMMING WITH RADIO FUNCTION ACTIVE: To be able to use both
modes (radio and wire), a remote control must be programmed before the adjustment
of the limit switches in the white wire mode. Once the programming has been
completed the motor enables use either by white wire, by radio, or using both modes
(radio/wire).
ACTIVATION/DEACTIVATION OF THE REMOTE CONTROL FUNCTION
To activate/deactivate the remote control function, follow the sequence shown below:
PLEASE NOTE: To deactivate the remote function it is rst necessary to totally delete the
remote controls from the memory of the motor (page 40 Tronic RX manual).
Activation/deactivation from the OPENING position:
Activation/deactivation from the CLOSING position:
21
The conrmation movements indicate that the remote control function activation/
deactivation procedure has been successfully carried out.
ENGLISH

22
KEY TO SYMBOLS
UP DOWN
Press the
UP-button
Press the buttons quickly according to the sequence indicated
Press the buttons quickly according to the sequence indicated.
The motor will carry out a movement to conrm your settings.
Press the
DOWN-button
DOWN DOWNUP
DOWN DOWNUP
short motor
rotation in one
direction
long motor
rotation in
other direction
down
up
COMMAND SEQUENCES EXAMPLE
Most of the command sequences have three or six distinct steps, at the end of which the
motor indicates if the step has been concluded positively or not, by turning in different
ways.This section is provided to demonstrate the motor indications. The buttons must be
pressed for at least 0,5 seconds as shown in the sequence, without taking more than 1
second between one step and the next. If more than 1 second is taken, the command is
not accepted and the sequence must be repeated.
Command sequence example:
As we can see from the example, when the sequence ends positively, the motor carries
out one long rotation.
If the motor does not carry out any rotation, this means that the sequence has failed. In
this case the sequence must be carried out again from the start.
Attention! If the sequence requires a repetition of the same commands (Up+Up/
Down+Down), an interposition of the Stop position could be necessary depending
on the type of switch in use.
UPUP UP
ENGLISH

23
MOTOR PROGRAMMING FROM THE WHITE WIRE
ADJUSTMENT OF THE LIMIT SWITCHES
PLEASE NOTE. If the motor is programmed from the white wire without rst having
memorised at least one remote control, the remote function will be deactivated
automatically (to reactivate it, see page 21 - ACTIVATION/DEACTIVATION OF THE
REMOTE CONTROL MOTOR FUNCTION).
Motor programming from the white wire is active until the limit switches have been
programmed. Once the limit switches have been programmed, the possibility of
programming the motor from the white wire remains enabled for a maximum time of 5
minutes; this to enable the changing of certain functions such as the adjustment of the
closing force, the middle position, etc.
Each time that the motor power supply is disconnected and the motor is then powered
up again, the programming function from the white wire is reactivated (always with a
maximum duration of 5 minutes).
During adjustment the motor will advance with a short movement and then a pause
followed by a continuous movement in the desired direction.
The limit switch adjustments may be made in different ways depending on the locking
devices tted onto the shutter (spring and plug anti-intrusion locks) and the type of
installation (factory installed or job-site installation).
SETTING IN MODE 1 (manual)
In this mode it doesn’t matter whether or not the rolling shutter has got physical stops in
the opening position and the lockdown hangers in the closing position. It is possible to
choose whether to set the upper limit or the lower limit rst. The correct rotation direction
will only be identied after the rst position is set so it is sometimes necessary to use the
“up” or “down” button.
NOTE FOR OPERATION FROM THE BUTTON SWITCH
The motor automatically recognizes the switch-type (with 1 or 2 buttons) and sets the
proper operational mode. Following the automatic recognition and after the wire setting,
if required the motor changes the association of the switch buttons to adapt them to the
correct drive direction (Up - Down). At this point, if the drive direction does not match
with the buttons, the motor resets the proper association upon the rst complete Up/
Down cycle. During this cycle the motor performs a technical stop and then automatically
starts back up.
ENGLISH

24
EXAMPLE N. 1
Setting rst the opening position
SETTING THE OPENING POSITION
SETTING THE CLOSING POSITION
If the rolling shutter is completely open, you have rst to drive it down by
around 20 cm.
Bring the rolling shutter to the opening position using the UP or DOWN button. (Open
position).
With physical stops: press UP or DOWN button until the motor stops automatically.
Without physical stops: use the UP or DOWN button to drive the rolling shutter to the
necessary opening position.
Follow the command sequence given in order to save the opening position.At the end of
the sequence, the motor carries out a short “down” movement which conrms that the
settings have been saved.
Pressing now the DOWN button, drive completely down the rolling shutter to the closing
position.
With lockdown hangers: press the DOWN button until the motor stops automatically.
Without lockdown hangers: use UP or DOWN button to drive the rolling shutter to the
necessary closing position.
Follow the command sequence given in order to save the closing position. At the end of the
sequence, the motor carries out a short “up” movement which conrms that the settings
have been saved.
?
DOWN
UP
UPUP UP
conrm
conrm
DOWN DOWN DOWN
ENGLISH

25
EXAMPLE N. 2
Setting rst the closing position
SETTING THE CLOSING POSITION
SETTING THE OPENING POSITION
If the rolling shutter is completely closed, you have rst to drive it up by around
20 cm.
Bring the rolling shutter to the closing position using the UP or DOWN button. (Closed
position).
With lockdown hangers: press UP or DOWN button until the motor stops automatically.
Without lockdown hangers: use the UP or DOWN button to drive the rolling shutter to
the necessary closing position.
Follow the command sequence given in order to save the closing position. At the end
of the sequence, the motor carries out a short “up” movement which conrms that the
settings have been saved.
Pressing now the UP button, drive completely up the rolling shutter to the open position.
With physical stops: press the UP button until the motor stops automatically.
Without physical stops: use UP or DOWN button to drive the rolling shutter to the
necessary opening position.
Follow the command sequence given in order to save the opening position. At the end of
the sequence, the motor carries out a short “down” movement which conrms that the
settings have been saved.
?
DOWN
UP
DOWN DOWN DOWN
conrm
conrm
UPUP UP
ENGLISH

26
MODE 2: LIMIT SWITCH SETTING (semi-automatic)
SETTING THE OPENING POSITION
To do the settings in this mode the rolling shutter has to be equipped with lockdown
hangers in the closing position, but the rolling shutter does not need to have physical
stops in the opening position. This mode of setting is helpful in cases where the factory
will set the opening position and the closing position will be set automatically during
the normal use.
In this mode, it’s necessary to set rst the opening position!! (Rolling shutter open!)
If the shutter is already completely open, you have rst to drive it down by
about 20 cm.
Bring the rolling shutter to the opening position using the UP or DOWN button. (Open
position).
With physical stops: press UP or DOWN button until the motor stops automatically.
Without physical stops: use the UP or DOWN button to drive the rolling shutter to the
necessary opening position.
Follow the command sequence given in order to save the opening position. At the end
of the sequence, the motor carries out a short “down” movement which conrms that
the settings have been saved and then it brings back the shutter to the opening position.
Now the drive direction is detected and the motor can be disconnected from the power.
The closing position will be set automatically during the normal use.
The lower limit switch position will be set automatically the rst time the rolling shutter
stops automatically in the closing position using the lock down hangers. As the motor
looks for a “mechanical” stop during each way down, if the Obstacle Recognition
nds something is blocking the way (such as a protruding screw in the guide rails), it is
necessary to raise the shutter again, remove the obstacle and to drive the motor back to
the closing position to set the limit.
?
DOWN
UP
UP UP UPDOWN DOWN DOWN
conrm
ENGLISH

27
ENGLISH
SETTING/DELETING A MIDDLE POSITION
From the OPENING position
From the CLOSING position
From the OPENING position
From the CLOSING position
After the sequence the motor will go into “Dead Man” mode so as to enable the exact
adjustment of the middle position desired. To memorise the position chosen, conrm
with this sequence:
DELETING THE MIDDLE POSITION
Use one of the sequences shown here.The motor will conrm with 3 nal movements that
the middle position has been cancelled.
MOVEMENT TO MIDDLE POSITION
To move the shutter to the
middle position, use one of
the methods below:
MOVEMENT TO MIDDLE POSITION
2 sec

28
CLOSING FORCE ADJUSTMENT
This system is the only one of its kind and it guarantees that rolling shutters (which are
equipped with lockdown hangers) remain perfectly closed without any danger of the
slats suffering excessive pressure. The system works in all kinds of applications because
of the opportunity of manually adjusting the closing force.
The Tronic RX is factory set to a closing force of 20 % of the nominal torque.This force can
be changed very easily using the up-down button. It can be reduced by 10 % or increased
up to 40 %, depending on the desired result.
DOWNUPUP
DOWN DOWN UP
DOWN UP UP
DOWNDOWNUP
DOWN DOWN UP
DOWNUPUP
DOWN DOWN DOWN
UP UPUP
10 %
10 %
20 %
20 %
40 %
40 %
From the CLOSING position
From the OPENING position
conrm
conrm
ENGLISH

29
ACTIVATION/DEACTIVATION SUPER-SENSITIVITY FUNCTION
(only for Ø 35 motors)
From the OPENING position
From the CLOSING position
DELETING THE OPENING AND CLOSING LIMIT SWITCH
From the OPENING position
From the CLOSING position
UP UP UP UP UPDOWN
UPDOWN DOWN DOWN DOWN DOWN
After deletion of the limit switches the radio function automatically resets.
ENGLISH

Rev: 2 08/2019 - Cod: A4518_6B46
CHERUBINI Deutschland GmbH
Siemensstrasse, 40 - 53121 Bonn - Deutschland
Tel. [phone] / 35 | Fax [phone]
[e-mail] | www.cherubini-group.de
CHERUBINI France S.a.r.l.
ZI Du Mas Barbet
165 Impasse Ampère
30600 Vauvert -France
Tél. [phone] | Fax [phone]
[e-mail] | www.cherubini.fr
CHERUBINI Iberia S.L.
Avda. Unión Europea 11-H
Apdo. 283 - P. I. El Castillo
03630 Sax Alicante - Spain
Tel. [phone] | Fax [phone]
[e-mail] | www.cherubini.es
CHERUBINI S.p.A.
Via Adige 55
25081 Bedizzole (BS) - Italy
Tel. [phone] | Fax [phone]
[e-mail] | www.cherubini.it