Cisco TelePresence DX80 User manual

1
78-100265-02 A0 | MAY 2014 © 2014 Cisco Systems, Inc. All rights reserved.
Cisco DX80
INSTALLATION GUIDE

2
Optional Accessories
• VESA adapter and wall mount kit
User Guides
For user guides and compliance and safety information for this product, go to:
http://www.cisco.com/go/dx-docs
Room Setup
For more information on how to set up your room for the best video experience,
visit the Project Workplace tool at http://www.cisco.com/go/projectworkplace
Accessories
AEthernet cable (2.9 m/9.5ft)
CHDMI/USB cable (2m/ 6.56ft)
BPower adapter and regional power cable
DCleaning cloth
Always use the provided Lite-On PA-1600-2A-LF power supply (input: 2 A, 100-240 V, 50-60Hz;
output: 5.0 A, 12.0V) or FSP075-DMAA1 (input: 1.2A, 100-240V, 50-60Hz; output: 6.5 A, 12.0 V).

3
Connect Cables
1. Place the DX80 face down on a flat surface to connect the cables. Do not exert force
on the camera as this may damage it.
2. Flip the connector cover up to access the connector panel and lead the cables under
the strain relief bar.
3. Connect the Ethernet cable (A) between the network connector
1
and a network
wall socket.
4. Connect the provided power adapter and cable (B) between the DX80
2
and a
power socket.
5. Pull the foot stand, set the DX80 in an upright position and adjust the angle. The foot
stand is stiff to open at first.
To use the same network wall socket for both your computer and DX80, connect your
computer to the computer network port on the DX80, and the DX80 to the network wall
socket (see step 3).
Computer
network
Micro-SD
slot
Network
Kensington
lock
USB
HDMI in
Factory
reset
pinhole
Power USB
Type B
HDMI out
(not in use)
Service port
2 3 4 1

4
Start the System
1. Push the power button to start up the DX80. The power button’s LED lights up when
the device starts up.
2. Follow the on-screen instructions to set up the system.
For more information on how to set up the system, see the Administrator Guide at
http://www.cisco.com/go/dx-docs
Connect to Computer
Connect your computer to the DX80 to use it as an external monitor and to enable
content sharing.
1. Connect the HDMI-USB bundle (C) to the USB Type B 3and the HDMI 4connec-
tors on the DX80.
2. Connect the USB and HDMI connectors on the other end to the computer. You may
need an adapter (not provided) for the HDMI cable, depending on the connectors
available on your computer.
3 4

5
Power button
Microphone
Front and Side Panels
Turn the privacy shutter to switch the camera on and off.
Use the Source button to show and hide your computer screen when a computer is
connected to the DX80.
You can tilt the camera to adjust the camera angle and to activate the document camera
feature.
Adjust the foot stand to take advantage of the extended tilt of the touch screen.
Adjust Camera and Stand
Speaker
Microphone
Camera privacy shutter
Source button
Mute
Volume
USB

6
On our web site you will find an overview of the
worldwide Cisco contacts.
Go to: http://www.cisco.com/web/siteassets/contacts
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Dr.
San Jose, CA 95134 USA
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and
other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party
trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (1110R)