Cisco 7811 User manual

Wall Mounts
•Wall Mount Kits, on page 1
•Non-Lockable Wall Mount Components for 7811, on page 2
•Non-Lockable Wall Mount Components, on page 9
•Non-Lockable Wall Mount Components for 7861, on page 17
•Adjust the Handset Rest, on page 25
Wall Mount Kits
Each wall mount is unique to your phone model and cannot be used for another phone. If you are planning
to attach your phone to a wall, purchase the wall mount kit specific to your phone.
For part numbers and other additional information, refer to the phone model data sheet. The Cisco IP Phone
8800 Series data sheets can be found here https://www.cisco.com/c/en/us/products/collaboration-endpoints/
unified-ip-phone-8800-series/datasheet-listing.html. The Cisco IP Phone 7800 Series data sheets can be found
here https://www.cisco.com/c/en/us/products/collaboration-endpoints/unified-ip-phone-7800-series/
datasheet-listing.html.
To check which phone model you have, press Applications and select Phone information. The Model
number field shows your phone model.
Table 1: Wall Mount Kits
NotesCisco Wall Mount KitCisco IP Phone
Spare Wallmount Kit for Cisco IP Phone 7811
(CP-7811-WMK=)
Cisco IP Phone 7811
Spare Wallmount Kit for Cisco IP Phone 7800 Series
(CP-7800-WMK=)
Cisco IP Phone 7821 and 7841
Spare Wallmount Kit for Cisco IP Phone 7861
(CP-7861-WMK=)
Cisco IP Phone 7861
Wall Mounts
1

Non-Lockable Wall Mount Components for 7811
The following figure shows the components of the Cisco IP Phone 7811 Wall Mount Kit.
Figure 1: Wall Mount Kit Components for 7811
The package includes these items:
• One phone bracket
• One wall bracket
• Four M4 x 25-mm Phillips-head screws with four anchors
• Two M3 x 7-mm Self-tapping screws
• One 200-mm Ethernet cable
This section describes how to install and remove the ADA nonlockable wall mount kit.
Figure 2: Back View of ADA Non-Lockable Wall Mount Kit Installed on Phone
Wall Mounts
2
Wall Mounts
Non-Lockable Wall Mount Components for 7811

Figure 3: Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone
Install the Non-Lockable Wall Mount Kit for 7811
The wall mount kit can be mounted on most surfaces, including concrete, brick, and similar hard surfaces.
To mount the kit on concrete, brick, or similar hard surfaces, you must provide the appropriate screws and
anchors for your wall surface.
Before you begin
You need these tools to install the bracket:
• #1 and #2 Phillips-head screwdrivers
• Level
• Pencil
You must also install an Ethernet jack for the phone in the desired location if an Ethernet jack does not currently
exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a regular phone jack.
Procedure
Step 1 Mount the wall bracket in the desired location. You can install the bracket over an Ethernet jack, or you can
run the Ethernet network cable to a nearby jack.
If the jack is to be placed behind the phone, the Ethernet jack must be flush to the wall or recessed.
Note
a) Hold the bracket on the wall and place it so that the arrow on the back of the bracket points up.
b) Use the level to ensure that the bracket is level and use a pencil to mark the screw holes.
c) Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the anchor
into the wall.
d) Screw the anchor clockwise into the wall until it is seated flush.
e) Use the included screws and a #2 Phillips-head screwdriver to attach the bracket to the wall.
Wall Mounts
3
Wall Mounts
Install the Non-Lockable Wall Mount Kit for 7811

Figure 4: Bracket Installation
Step 2 Attach the phone bracket to the IP Phone.
a) Detach the power cord and other attached cords from the base of the phone, except the handset cord (and
headset cord, if there is a headset).
b) Attach the phone bracket by inserting the tabs into the mounting tabs on the back of the phone. The phone
ports should be accessible through the holes in the bracket.
c) Reattach the cords and seat them in the clips that are incorporated into the phone body.
Wall Mounts
4
Wall Mounts
Install the Non-Lockable Wall Mount Kit for 7811

Figure 5: Phone Bracket Attachment
Screw holes1
Step 3 Attach the cables to the phone:
a) Attach the Ethernet cable to the 10/100/1000 SW network port and wall jack.
b) (Optional) If you are connecting a network device (such as a computer) to the phone, attach the cable to
the 10/100/1000 Computer (PC access) port.
c) (Optional) If you use an external power supply, plug the power cord into the phone. Dress the cord by
clipping it into the clips that are incorporated into the phone body next to the PC port.
d) (Optional) If the cables terminate inside the wall bracket, connect the cables to the jacks.
Wall Mounts
5
Wall Mounts
Install the Non-Lockable Wall Mount Kit for 7811

Figure 6: Cable Attachment
Handset Port4Phone Bracket1
AC Adapter Port5Network Port2
Optional Power Cable6Wall Bracket3
Step 4 Attach the phone to the wall bracket by inserting the tabs on the top of the wall bracket into the slots on the
phone bracket.
For cables that terminate outside of the brackets, use the cable-access openings in the bottom of the bracket
to position the power cord and any other cable that does not terminate in the wall behind the bracket. The
phone and wall bracket openings together form circular openings with room for one cable per opening.
Wall Mounts
6
Wall Mounts
Install the Non-Lockable Wall Mount Kit for 7811

Figure 7: Phone to Wall Bracket Attachment
Step 5 Press the phone firmly into the wall bracket and slide the phone down. The tabs in the bracket click into
position.
Step 6 Proceed to Adjust the Handset Rest, on page 25.
Remove the Phone from the Non-Lockable Wall Mount for 7811
The wall mounting plate contains two tabs to lock the plate into the phone bracket. The following figure shows
the location and shape of the tabs.
Wall Mounts
7
Wall Mounts
Remove the Phone from the Non-Lockable Wall Mount for 7811

Figure 8: Tab Location
To remove the phone and mounting plate from the wall bracket, you must disengage these tabs.
Before you begin
You require two screwdrivers or metal rods.
Procedure
Step 1 Push the screwdrivers into the left and right holes in the phone mounting plate approximately 1 in. (2.5 cm).
Step 2 Lift the screwdriver handles up to push down on the tabs.
Wall Mounts
8
Wall Mounts
Remove the Phone from the Non-Lockable Wall Mount for 7811

Figure 9: Disengage Tabs
Step 3 Press firmly to disengage the tabs and move the phone up at the same time to release the phone from the wall
bracket.
Non-Lockable Wall Mount Components
The following figure shows the components of the Cisco IP Phone 7800 Series Wall Mount Kit.
Figure 10: Wall Mount Kit Components
The package includes these items:
• One phone bracket
• One wall bracket
• Four M8-18 x 1.25-inch Phillips-head screws with four anchors
Wall Mounts
9
Wall Mounts
Non-Lockable Wall Mount Components

• Two M2.5 x 6-mm machine screws
• One 6-inch Ethernet cable
This section describes how to install and remove the ADA nonlockable wall mount kit.
Figure 11: Back View of ADA Non-Lockable Wall Mount Kit Installed on Phone
Figure 12: Side View of ADA Non-Lockable Wall Mount Kit Installed on Phone
Wall Mounts
10
Wall Mounts
Non-Lockable Wall Mount Components