Cisco 7942G - Unified IP Phone VoIP User manual

Home
PBXware
SERVERware
TELCOware
SIPmon
SIPProt
Desktop & Mobile
BRM
UADs
Appliances
EOL
From Bicom Systems Wiki
Contents
1 Introduction
■
2 Requirements
■
2.1 Identifying phone model
■
2.2 Phone firmware
■
2.3 DHCP server
■
2.4 PBXware version
■
3 Installation
■
3.1 Power adapter
■
3.2 Reset to factory settings
■
4 Registering Phone
■
4.1 Manual Configuration
■
4.2 Auto Provisioning Configuration
■
Introduction
This "How to" is written as general guide on how to use Cisco 7942G with PBXware using SIP
7.1 Cisco 7942G firmware. It covers the most common tasks that are required to have your
Cisco 7942G working efficiently.

Requirements
Identifying phone model
To start and successfully complete registration of your Cisco phone you need to know which
phone model you will setup.
On the front of each Cisco phone there are exact model information that you should check.
Although different phone models can have exactly the same requirements and installation
procedure, phone models can also have significantly different requirements and installation
procedure, so that ignorance of your own model may result in the inability to successfully set up
your phone.
Phone firmware
Make sure that device is loaded with firmware (Application Load ID) 7.X or 8.X.
Press the Settings button.
■
Scroll to Status and press the select button.
■
Scroll to Firmware Versions and press the select button.
■
The firmware is listed under Application Load ID.
■
DHCP server
Fully configured and operational DHCP server.
PBXware version
In order to find out the PBXware version, please login to PBXware and navigate to Settings:
About. On the top of About page is a code similar to this one "PBXware Edition: Business,
Release: 3.1 (041373f), Running: 1.4.24-gc-75ee203", where "Release" denotes the exact version
of your PBXware.

Installation
This chapter describes how to install and connect the phone to the electrical power and data
network as well as how to apply factory settings.
The following topics are covered:
Power adapter
■
Factory settings
■
Power adapter
Connect the Network and Power
Connect the DC plug on the power adapter to the DC port on the phone and connect the other
■
end of the power adapter into an electrical power outlet.
Connect the ethernet cable between the Internet port on the phone and the network port on a
■
router or switch to access LAN.
Reset to factory settings
Reset to factory settings
This step is not required for out-of-the-box phones, however, if the phone has been already used
then it is a must.
Unplug the power cable from the phone.
■
Hold down the # key, and then plug the power cable in again. The phone should begin its
■
power up cycle.
Release the # key after the Speaker button is no longer lit. You should this message displayed
■
on the phone: Reset key sequence detected
Press 123456789*0# (or in some cases this sequence is 3491672850*# ) within 60 seconds
■
after the Headset, Mute, and Speaker buttons begin to flash.
-If you fail to complete this key sequence or do not press any keys, the Headset, Mute, and
Speaker buttons will stop flashing after 60 seconds and the phone will continue with its normal
start-up process. The phone will not reset.
-If you enter an invalid key sequence, the buttons will stop flashing immediately and the phone
will continue with its normal start-up process. The phone will not reset.
If you enter this key sequence correctly, the phone displays this prompt:
■
Keep network cfg? 1 = yes 2 = no
-To maintain existing network configuration settings for the phone when the phone resets, press
1.
-To reset network configuration settings when the phone resets, press 2.
-If you press another key or do not respond to this prompt within 60 seconds, the phone will

continue with its normal start-up process and will not reset.
Registering Phone
Manual Configuration
UAD Settings
STEP ONE: PBXware IP address.
1. Find out the IP address of PBXware server.
STEP TWO: Login to PBXware.
1. Open a new browser window and enter the IP address to access the PBXware administration
interface login screen.
Example: http://192.168.1.2
2. Hit "Enter" on your keyboard.
3. Login to PBXware with your e-mail address and password.
STEP THREE: UAD status.
1. Make sure the UAD is enabled. To check the UAD status navigate to "Settings:UAD", and click
on the "edit" icon corresponding to "Cisco 7942G".
2. Make sure the "Status" is set to "active", "Auto provisioning" is set to "No" and "DHCP" is set
to "Yes".
3. Click on the "Save" button to save changes.

Creating Extension
STEP ONE: Add Extension.
1. Navigate to "Extensions". Click on "Add Extension".
2. The standard options window will be shown below.
Creating
Extension/Extensions Add
3. Select Cisco 7942G from "UAD" select box.
4. Select Location: "Local" or "Remote".
Note:
-"Local" is for all extensions registered on LAN.
-"Remote" is for all extensions registered from remote networks, WAN, Internet etc.
Creating
Extension/Extensions Add
5. Click on the "Next" button.
STEP TWO: Extension values.
1. Enter values into the required field text boxes.
REQUIRED FIELDS:
Name:
Enter a name for the extension being created. Example: John Smith.
E-mail:
Enter the e-mail address associated with this extension. This e-mail address will receive all
system notification messages. Example: [email protected].

Creating
Extension/Extensions Add
an example with details filled in
2. Click on the "Save" button.
Creating
Extension/Extensions Edit
an example with details filled in
3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address
associated with this extension.
OPTIONAL FIELDS:
Extension:
An auto-generated extension number based on the next available sequential number. An
extension value can be changed. Example: 1000.
Username:
Username is auto generated/populated and cannot be changed since it allows the system to use
this value for other important operations.
Secret:
A secret value associated with the UAD is auto-generated in order to allow the UAD to
successfully register with the system. The secret value can be changed.
PIN:
An auto-generated PIN will allow access to voicemail and online self care.
Registering Phone
STEP ONE: Electricity and Ethernet.
- Plug the power adapter into a power jack then connect it to the electricity network.
- Connect ethernet port to a hub, router or switch as to access LAN.
After successfully connecting the Cisco 7942G to the electricity and data networks, it is time to
register it to PBXware.
STEP TWO: Cisco 7942G settings configuration.

Unlock configuration:
1. Press the "settings" button.
2. Use the "navigation" button and navigate down to "Unlock Config".
3. Press the "Select" button.
4. Enter password (Default factory password is "cisco").
5. Press the "Accept" button to unlock configuration.
SIP Configuration
1. Using the "navigation" button navigate up to "SIP Configuration".
2. Press the "Select" button.
3. Press the "Select" button to enter into "Line 1 Settings".
4. Enter details into:
REQUIRED FIELDS:
Name
Cisco 7942G extension number. Example: 1000.
Authentication Name
Usually the same number as "Name".
Authentication Password
The Secret of the extension as received in the e-mail associated with this extension. Example:
3dX3r5
Proxy Address
IP address of PBXware server. Example: 192.168.1.2
OPTIONAL FIELDS
Shortname
Example: John Smith, Reception, Entrance Main, Agent One etc.
Display Name
Example: John Smith, Reception, Entrance Main, Agent One etc.
Proxy Port
By default 5060
5. Press accept button and reboot Cisco 7942G.
- Conclusion: If everything is done as above described you should have successfully registered
your Cisco 7942G to PBXware. Dial *123 to verify registration.
- For further information, please contact the manufacturer or check their web site

www.cisco.com.
Auto Provisioning Configuration
UAD Settings
STEP ONE: PBXware IP address.
1. Find out the IP address of PBXware server.
STEP TWO: Login into PBXware.
1. Open a new browser window and enter the IP address to access the PBXware administration
interface login screen.
Example: http://192.168.1.2
an example with IP address
2. Hit "Enter" on your keyboard.
3. Login to PBXware with your e-mail address and password.
STEP THREE: UAD status.
1. Make sure the UAD is enabled. To check the UAD status navigate to "Settings:UAD", and click
on the "edit" icon corresponding to "Cisco 7942G".
2. Make sure "Status" is set to "active", "Auto provisioning" is set to "Yes" and "DHCP" is set to
"Yes".
3. Click on the "Save" button to save changes.
Creating Extension
STEP ONE: Add Extension.

1. Navigate to "Extensions". Click on "Add Extension".
2. The standard options window will be shown below.
Creating
Extension/Extensions Add
3. Select Cisco 7942G from "UAD" select box.
4. Select Location: "Local" or "Remote".
Note:
-"Local" is for all extensions registered on LAN.
-"Remote" is for all extensions registered from remote networks, WAN, Internet etc.
Creating
Extension/Extensions Add
5. Click on "Next" button.
STEP TWO: Extension values.
1. Enter values into required field text boxes.
REQUIRED FIELDS:
Name:
Enter a name for the extension being created. Example: John Smith.
E-mail:
Enter the e-mail address associated with this extension. This e-mail address will receive all
system notification messages. Example: [email protected]
Auto provisioning:
Set to "Yes".
MAC Address:
Cisco 7942G MAC address. Example: 001646f5f797

Creating
Extension/Extensions Add
an example with details filled in
2. Click on the "Save" button.
Creating Extension
an example with details filled in
3. Click on the "Save & E-mail" button. Account details will be sent to the e-mail address
associated with this extension. OPTIONAL FIELDS:
Extension:
An auto-generated extension number based on the next available sequential number. An
extension value can be changed. Example: 1000.
Username:
Username is auto generated/populated and cannot be changed since it allows the system to use
this value for other important operations.
Secret:
A secret value associated with the UAD is auto-generated in order to allow the UAD to
successfully register with the system. The secret value can be changed.
PIN:
An auto-generated PIN will allow access to voicemail and online self care.
Registering Phone
STEP ONE: Electricity and Ethernet.
- Plug the power adapter into a power jack then connect it to the electricity network.
- Connect the ethernet port to a hub, router or switch as to access LAN.
"TFTP Server" must be set with TFTP server value.
STEP TWO: Cisco 7942G TFTP configuration.