Cleveland KEL-80-T User manual

Cleveland
™
Project ________________________________
Item __________________________________
Quantity_______________________________
FCSI Section ____________________________
Approval _______________________________
Date __________________________________
1333 East 179 St.,
Cleveland, Ohio,U.S.A. 44110
Tel: [phone]
Fax: [phone]
Web Site:www.ClevelandRange.com
Email: [e-mail]
ELECTRIC KETTLES
SECT. VIII PAGE 11
0707
Cleveland Standard Features
n Self-contained, easily installed - needs only an electrical hook-up
nSteam jacket filled with treated water, venting and/or refilling is
not required
nAccurate, consistant solid state temperature controls (mechani-
cal thermostate not as accurate) - less than ±1°C variance
(ideal for simmering). Operating temperature range from 145° -
260°F (63°C - 127°C)
Control panel includes:
•LED indicator for heat cycle • LED indicator for low water
•Power ON/OFF switch • Adjustable temperature control dial
nWater resistant controls, splash-proof construction
nLarge pouring lip for high capacity and chunky products
nRe-inforced rolled rim design prevents damage to kettle rim,
eliminates "bar rim designs"
nWelded-in heating elements, (holds vacuum better,won't leak
or loose water)
nEasily cleaned: kettle and all exterior surfaces are of type 304
stainless steel with an #4 finish
nRear mounted easy access pressure gauge and pressure relief
valve to prevent tampering. Color coded easy to read pressure
gauge with "green" and "vent air zone"
n50 psi steam jacket rating for higher cooking temperatures
n50 psi safety valve
n Solid state water level control (no sight glass gauge to break or leak)
nSplash proof element cover with a double gasket seal
nTilt mechanism of roller bearings and case hardened
self-locking worm and segment gear
n 15/8˝ O.D. tri-leg supports with level adjustable feet for floor bolt-
ing
nStandard voltage is 208-240 volts, 60 Hz, 3-phase, 3-wire
nTypical approvals include UL., CSA, CE, NSF and ASME
Options & Accessories
p Spring-assisted, hinged, rotatable, domed Stainless Steel Cover (CHS)
p2˝ or 3" diameter Tangent Draw-Off Valve (TD2 or TD3*)
*TD3 will raise height of kettle by 5-5/8" (143mm)
pHot and Cold Water Faucet with Swing Spout and Mounting
Bracket (DPK and FBKT)
pType 316 Stainless Steel Kettle Liner for high acid food
products (316)
pPan Carrier (PCK)
pFlow Diverter (FD)
pFood Strainers (FS)
pCooking Baskets and Tri-Basket Supports (BS and TBS)
pKettle Accessory Kit (KAK) includes:
pClean-up Brush (CB) p36˝ Kettle Paddle (KP)
p36˝ Kettle Whip (KW) p36˝ Kettle Brush
pDraw-Off Brush (DB) p24 oz. Ladle (KL)
Shall be CLEVELAND, Electric Kettle, Quad-leg mounted, self-con-
tained, tilting, Model KEL - _____ - T; _____ gallons, 2⁄3 Steam
Jacketed. Type 304 Stainless Steel Kettle and Supports. 50 psi
Steam Jacket Rating; 50 psi Safety Valve; Permanently filled Steam
Jacket; Combination Pressure/Vacuum Jacket Gauge. Splash Proof
Solid State Temperature (±1°C) and Safety Control System in plug-
in Module including L.E.D. indicators,
pAutomatic Water Meter (GMF or LMF)
pDrain Strainers (DS-)
pWater Meter Stand (SWM)
pLift-Off Covers (CL)
pMeasuring Strip (MS)
pGallon Markings (KM)
pHot and cold or cold only Kettle Filler with 60˝ Hose (DKF-K or
SKF-K)
pSwing Funnels for drain (SW)
pAlternate Mounting Systems
pHigh Wattage (HW)
pSpecial Voltages
pHigh Wattage (HW) (see back page)
pSpecial Voltages (see back page)
pHeat Deflector Shield (HS001)
pCorrectional Packages
ShortFormSpecifications
Shown with optional spring-assisted
cover and 2" tangent draw-offvalve
QUAD-LEG, ELECTRIC KETTLES
TILTING, “ SPLASH PROOF SERIES”,
SELF-CONTAINED, 2⁄3 STEAM JACKETED,
80 or 100 GALLONS (300 or 375 LITERS)
MODELS:cKEL-80-T cKEL-100-T

(NOT TOSCALE)
SECT.VIII PAGE 12
0707
Litho in U.S.A.
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are U.L., NSF, CGA, CSA, ETL and others.
Z
G
F
E
KETTLE SHOWN WITH OPTIONAL SPRING ASSIST COVER,
WATER FAUCET AND T.D. VAVLE.
HANDWHEEL
REPLACED BY
SWITCH FOR
POWER
TILT OPTION
H
(I.D.)
2" T.D. VALVE
(AS SHOWN)
WALL
C
H
MANUAL TILT
EXTENDED
FOR POWER
TILT OPTION
T
V
U
POWER TILT
TANGENT
DRAW-OFF
VALVE
S
A2
P
X
FOOT LOCATION AND
FLOOR DRAIN DETAIL
Y
L
M
Q
W
J
L
N
FLOOR
DRAIN
DETAIL
2 3/4"
70
mm
REF
2 3/4"
70
mm
WALL
A1
SOLID FOOT DETAIL
51/2" (140 mm)
3/8"
(10 mm)
2"
(51
mm)
1" (26 mm)
MAX. ADJUSTMENT
5/8"
Ø
(16 mm)
2HOLES
ON 4"
(102
mm)
B.C.D.
RECOMMENDED
FLOOR SLOPE
1" (26 mm) per 4' (1220 mm)
PIPE DRAIN RECOMMENDED
min. valve size plus 1" (26 mm)
4" (102 mm)
RECOMMENDED
NOTE: TD3, 3" tangent draw off will
raise height of kettle by 5-5/8" (143mm).
CAPACITIES: (in 8 oz. servings,
other sizes may be calculated)
80 Gallon / 300 liters . . . 1280 servings
100 Gallon / 375 liters . . . 1600 servings
CLEARANCE
WATER
3⁄8˝O.D. copper tube or
1⁄2˝N.P
.T.pipe.
When ordered with
optional faucet.
H
C
RIGHT = 4.0˝ handle
clearance
LEFT = .00˝
REAR = .00˝
STANDARD WATTAGE
208V 240V 416V 480V
AMPS AMPS AMPS AMPS AMPS AMPS AMPS AMPS
GALS. LITERS KW 1PH 3PH KW 1PH 3PH KW 1PH 3PH KW 1 PH 3PH
80 300 14.7 70.8 40.9 19.6 81.7 47.1 18.1 43.5 25.1 19.6 40.8 23.6
100 375 14.7 70.8 40.9 19.6 81.7 47.1 18.1 43.5 25.1 19.6 40.8 23.6
HIGH WATTAGE
208V 240V 416V 480V
AMPS AMPS AMPS AMPS AMPS AMPS AMPS AMPS
GALS. LITERS KW 1PH 3PH KW 1PH 3PH KW 1PH 3PH KW 1 PH 3PH
80 300 29.4 NA 81.7 39.2 NA 94.3 36.2 87.0 50.2 39.2 81.7 47.1
100 375 29.4 NA 81.7 39.2 NA 94.3 36.2 87.0 50.2 39.2 81.7 47.1
DIMENSIONS
GALS./
LITERS A1 A2 EFGHJLMNPQSTUVWXYZ
80/ IN 48 1/2 54 1/8 84 47 7/16 17 33 24 1/4 11 3/8 32 1/2 67 3/8 35 1/2 5 1/2 48 44 5/8 8 5/8 40 1/4 21 1/2 40 3/4 24 1/4 52 1/8
300 mm 1232 1375 2134 1205 432 839 616 289 826 1712 902 140 1220 1134 220 1023 547 1036 62 133
100/ IN 51 56 5/8 89 7/8 48 11/16 16 1/4 35 1/2 25 5/8 11 5/8 36 71 1/4 40 1/2 4 49 1/2 47 9 1/4 40 23 43 1/4 25 5/8 53 3/8
375 mm 1296 1439 2283 1237 413 902 651 296 915 1810 1029 103 1258 1194 235 1016 585 1099 651 1355.8
Consult factory for other voltages.