Climax MZ-1 User manual

Table of Contents
Table of ContentsTable of Contents
Table of Contents
1. INTRODUCTION _____________________________________________________________________ 1
2. APPLICATION OVERVIEW _____________________________________________________________ 2
2.1. I DENTIFYING THE PARTS : _____________________________________________________________ 2
2.2. T HE P OWER S UPPLY :________________________________________________________________ 4
2.3. S YSTEM R EQUIREMENTS :_____________________________________________________________ 5
3. GETTING STARTED __________________________________________________________________ 6
3.1. H ARDWARE I NSTALLATION FOR MZ-1/8 __________________________________________________ 6
3.2. S OFTWARE I NSTALLATION FOR MZ-1/8___________________________________________________ 6
4. CONNECTING TO WEBPAGE __________________________________________________________ 9
5. SYSTEM SETTINGS _________________________________________________________________ 11
5.1. U SER __________________________________________________________________________ 11
5.2. R EPORT ________________________________________________________________________ 13
5.3. P ANEL __________________________________________________________________________ 16
5.4. A REA __________________________________________________________________________ 18
5.5. N ETWORK _______________________________________________________________________ 20
5.6. U PLOAD ________________________________________________________________________ 22
6. DEVICE MANAGEMENT ______________________________________________________________ 23
6.1. L EARNING _______________________________________________________________________ 23
6.2. A DD D EVICE _____________________________________________________________________ 26
6.3. W ALK T EST ______________________________________________________________________ 27
6.4. E DIT D EVICE _____________________________________________________________________ 28
6.5. D ELETE D EVICE ___________________________________________________________________ 31
6.6. R EQUEST M EDIA __________________________________________________________________ 31
6.7. P OWER S WITCH C ONTROL ___________________________________________________________ 32
6.8. S IREN L EARNING /C ONTROL __________________________________________________________ 32
7. CAPTURED EVENTS ________________________________________________________________ 33
8. HISTORY RECORDS _________________________________________________________________ 35
8.1. H ISTORY ________________________________________________________________________ 35
8.2. R EPORTED E VENT _________________________________________________________________ 36
9. PANEL CONTROL ___________________________________________________________________ 37
10. HOME AUTOMATION _______________________________________________________________ 38
11. FIRMWARE _______________________________________________________________________ 39

12. ALARM ACTIVATION TABLE _________________________________________________________ 39
13. VESTA EZ HOME APPLICATION ______________________________________ 錯誤 ! 尚未定義書籤。
13.1. F OR I P HONE ____________________________________________________ 錯誤 ! 尚未定義書籤。
13.2. F OR A NDROID P HONE _____________________________________________ 錯誤 ! 尚未定義書籤。
14. EVENT CODE _____________________________________________________________________ 42
1. Introduction
This manual covers the installation, programming, and control of IP based MZ-1 and MZ-8
control panels. Both MZ-1 and MZ-8 supports full range IP reporting capability with webpage for
setting configuration and system control, MZ-8 also has the extra function of reporting through
RF.
The advanced IP Security System with fully integrated TCP/IP technology and Ethernet
connectivity is able to take full advantage of new advances in IP Home Security and Home
Automation and multi-path signalling.
Remote control of the panel is achieved by registering the panel in our Home Portal Server.
With Home Portal Server, you can connect to your panel anytime, anywhere in the world
through internet connection either with a computer or a smartphone using our Vesta Home
application. Please refer to our Home Portal User Guide for detail about registering and using
Home Portal Server.
Remote programming and command is also available for MZ-8 to configure your panel by
messages. You can also use our Vesta EZ Home smartphone applications to send the
commands easily for basic panel functions.

2
2. Application Overview
2.1. Identifying the parts:
Case A
1. Panel Status LED (Dual Colour - Red & Green)
RED LED ON - System in Arm Mode.
RED LED FLASHES - System in Home 1/2/3 Mode.
GREEN LED ON - System in Disarm Mode.
GREEN LED FLASHES - System in Learn Mode.
LED OFF - System in Walk Test Mode
2. Alarm & Fault Status LED (Dual Colour - Red & Yellow) (with display priority)
RED LED FLASHES - System is currently alarming.
RED LED ON - Alarm memory in system.
YELLOW LED FLASHES - AC Power failure.
YELLOW LED ON – Other fault condition (not including AC Power Failure ).
LED OFF – System normal.
LED Flashing Sequence
： Alarm ＞ Alarm Memory ＞ Panel AC failure ＞ Other Fault

3
3. Operational Status LED (Dual Colour - Yellow & Red) (with display priority)
YELLOW LED ON - Network error
LED OFF – Network ok
LED Flashing Sequence: Network ok ＞ Network error
4. Buzzer
5. Ethernet Port
6. Learn / Reset Button
7. Empty Port
8. DC Jack
For connecting the DC 12V, 1A
switching power.
9. Battery Switch
10. Tamper Switch
11. Wall Mounting Bracket
Case B
1. Panel Status LED (Dual Colour - Red & Green)
RED LED ON - System in Arm Mode.
RED LED FLASHES - System in Home 1/2/3 Mode.
GREEN LED ON - System in Disarm Mode.
GREEN LED FLASHES - System in Learn Mode.
LED OFF - System in Walk Test Mode
2. Alarm & Fault Status LED (Dual Colour - Red & Yellow) (with display priority)
RED LED FLASHES - System is currently alarming.
RED LED ON - Alarm memory in system.
YELLOW LED FLASHES - AC Power failure.

4
YELLOW LED ON – Other fault condition (not including AC Power Failure ).
LED OFF – System normal.
LED Flashing Sequence ： Alarm ＞ Alarm Memory ＞ Panel AC failure ＞ Other Fault
3. Operational Status LED (Dual Colour - Yellow & Red) (with display priority)
YELLOW LED ON - Network error
LED OFF – Network ok
LED Flashing Sequence: Network ok ＞ Network error
4. Standing Base
5. Internal Buzzer
6. Ethernet Port
7. Learn/Reset Button
8. Base
9. DC Jack
For connecting the DC 12V, 1A
switching power.
10. Battery Switch
2.2. The Power Supply:
An AC power adapter is required to connect to a wall outlet. Be sure only to use an adapter with
the appropriate AC voltage rating to prevent component damage. DC 12V 1A switching power
output adaptor is generally used to power the Control Panel for standard version.
Rechargeable Battery
 In addition to the adapter, there is a rechargeable battery inside the Control Panel, which
serves as a back up in case of a power failure.
 During normal operation, the AC power adapter is used to supply power to the Control
Panel and at the same time recharge the battery. It takes approximately 72 hours to fully
charge the battery.
<
<N NO OT TE E> >
If the AC power is missing and the battery is near exhaustion, a low battery message
will be displayed and the internal siren will be disabled to conserve power.

5
2.3. System Requirements:
The system requires a TCP/IP network environment for MZ-1/8 IP Panel to be included in your
network.
To install the CD Wizard, your computer must have:
Microsoft Windows 98, ME, NT4.0, 2000, XP, Vista, 7 or 8 operating system.
Microsoft Internet Explorer 5.x, or later and Mozilla Firefox 1.0 compatible.
CD-ROM drive
CPU: Intel Pentium II 266MHz or above
Memory: 32MB (64MB recommended)
VGA resolution: 800x600 or above

6
3. Getting Started
Read this section of the manual to learn how to set up your MZ-1/8 Panel and program System
Settings over the Web page.
3.1. Hardware Installation for MZ-1/8
Step 1. Connect the Power Adaptor to a Wall Outlet and the other end to MZ-1/8. MZ-1/8 will
emit one short beep and Panel Status GREEN LED will turn ON.
Step 2. Connect the Ethernet cable as described below:
Step 2A: Plug-in the ethernet cable into the Internet jack on the Control Panel.
Step 2B: Plug-in the other end of the enclosed Internet cable into your Net Router port.
Step 2C: Once the Internet Set-up is successful, please leave the cable connected.
Step 3. Hardware installation for MZ-1/8 is now complete.
3.2. Software Installation for MZ-1/8
※
※※
※ THIS INSTALLATION IS ONLY REQUIRED FOR FIRST TIME USER ※
※※
※
1. RUNNING THE MZ-1/8 FINDER
To install the “Finder” software”
Step 1. Insert the supplied CD-ROM into your CD-ROM drive
Step 2. Find the Finder software in the CD-ROM
Step 3. Double click on the Finder to initiate the installation.
Step 5. Click “Change” to select the file folder, if no change is required; click “Next” to get
ready for the installation process.

7
Step 6. Click “Next” to begin the Installation. Once the installation is completed, click “Finish”
to confirm.
Step 7. A new icon will be displayed on your desktop.
Step 8. Double click on the “Finder.exe” to start the installation. The following screen will be
displayed:
Step 9. Click on “Search”, It will start searching for recognized IP address within the Local
Network Service.
Step 10. You will be able to locate the current MZ-1/8 IP address among the list.
Displayed with MAC Address and Product version.
Step 11. Once MZ-1/8 is identified, select MZ-1/8 and click on “Open Web Page” to link to the
IP Security System Web page.
Step 12. Software installation for MZ-1/8 IP Panel is now completed.

8
2. CONFIGURE SETTING
The Configure setting is for you to setup the network setting manually.
Step 1. Click on Configure Setting, the following window will display:
Step 2. Enter the network information and MZ-1/8’s web user name and password.
(Default) User Name: admin
(Default) Password: admin1234
Step 3. Click on OK to confirm. When the username and password are correct, a window will
display: Status: Configure success!!

9
4. Connecting to Webpage
Step 1. Select MZ-1/8 in the Finder software and click on “Open Webpage” to connect to
MZ-1/8 webpage.
Alternatively, enter MZ-1/8 IP address displayed in Finder into your browser’s address
section and click “GO”.
Step 2. Enter the User name & Password.
Step 3. Enter the User name & Password and then press “OK”.
User Name: admin Password: admin1234

10
Step 4. You will enter the Control Panel webpage, the current Control Panel information will be
displayed.

11
5. SYSTEM SETTINGS
5.1. User
User Code
The User Codes are used for users to acess the alarm system. A total of 10 4-digit User
Codes can be stored in MZ-1/8. Each individual User can be given a name for easy
recognition when viewing system events.
User PIN code #1 is activated with “1234” as factory default. User PIN code #2~#10 are
deactivated by factory default
<
<N NO OT TE E> >
When entering User PIN Codes with a Remote Keypad, if the wrong PIN Codes were
entered 5 times in 10 minutes, the Control Panel will prohibit further User PIN Code
entry for 15 minutes. All User PIN Codes entered during the 15 minute period will result
in error for the Remote Keypad.
Guard Code
The Guard Code is designed for security personnel to arm/disarm the system. When this
code is used for accessing the system, the Control Panel will record the event separately
from the User Codes.
The Guard Code consists of 4 digits and is not activated as default by the factory.
Master Code
This function is currently disabled
Factory default: 1111.

12
 Temporary Code
The Temporary Code is used to access the system for a temporary user and is valid only
once per arming and once per disarming. Afterwards, the Temporary Code is
automatically erased and needs to be reset for a new Temporary user.
The Temporary Code consists of 4 digits and is not activated as default by the factory.
Duress Code
The Duress Code is used to access the system in duress situation. When this code is used
for accessing the system, the Control Panel will report a secret alarm message without
sounding the siren to the Central Monitoring Station to indicate of a “Duress Situation in
Progress”.
The Duress Code consists of 4 digits and is not activated by factory default.
Installer Code
The Installer Code is used for the installer to access the Control Panel via remote
command.
Factory default: 7982.
Latch Option
Whe the option is selected, the Control Panel will report all arming/disarming action by this
user.
Latch.
When the the Latch option box is ticked, the Latch option is turned ON.
To edit the Codes on Web Page:
Step 1. Key in your preferred 4-digit code
Step 2. Enter a name for the code (optional)
Step 2. Choose to tick On / Off the Latch Option box.
Step 3. Press “Submit” to confirm the new uploaded details.

13
5.2. Report
This page is for you to enter the report destination setting. MZ-1/8 can store up to 8 report
destinations.
 Reporting Type:
MZ-1/8 supports 5 reporting types:
 IP/RF reporting in CID format:
Reporting destination format: ip://Account@Server IP:Port/CID
For Example: ip://[email protected].22:8765/CID
ip:// 6543 @59.124.123.23
:8765 /CID
Reporting
type
Account
(4-8 digits)
Server IP
address
Port
number
Reporting
Format
 IP/RF reporting in SIA format:
Reporting destination format: ip://Account@Server IP:Port/SIA
For Example: ip://[email protected].22:8765/SIA
ip:// 6543 @59.124.123.23
:8765 /SIA
Reporting
type
Account
(4-8 digits)
Server IP
address
Port
number
Reporting
Format
 IP/RF reporting in CSV format:
Reporting destination format: ip://Account@Server IP:Port/CSV
For Example: ip://[email protected].22:8765/SIA
ip:// 6543 @59.124.123.23
:8765 /CSV
Reporting
type
Account
(4-8 digits)
Server IP
address
Port
number
Reporting
Format

14
 IP/RF reporting in CSV format with user name and password:
Reporting destination format: ip://Account@Server IP:Port/CSV/User/Password
For Example: ip://6543@59.124.123.22:8765/CSV/ABCD/1234
ip:// 6543 @59.124.123.23
:8765 /CSV /ABCD /1234
Reporting
type
Account
(4-8 digits)
Server IP
address
Port
number
Reporting
Format
User
Name
Passwo
rd
 Reporting in format: (MZ-8 only)
Reporting destination format://Account@mobile number/CID
For Example: //1234@0926064587/CID
:// 1234 0926064587 /CID
Reporting
type
Account
(4-8 digits)
Mobile Number Reporting
Format
 reporting in Text format: (MZ-8 only)
Reporting destination format:://mobile number/TEXT
For Example: /0926064587/TEXT
:// @0926064587 /TEXT
Reporting type Mobile Number Reporting Format
 Digital reporting in format: (MZ-8 only)
Reporting destination format: // Account@Tel number
For Example: //1234@0926064587
// 1234 @27940001
Reporting type Account (4-8 digits)
Telephone Number
 Email reporting
Reporting destination format: mailto: [e-mail]
For Example: mailto: sal[email protected]
mailto: [email protected]w
Reporting type Email Account
<
<N NO OT TE E> >
Reporting type must be entered in lowercase letters
SMTP setting must be completed first for email reporting to function.

15
 Groups:
You can assign reporting destinations to different groups, the reporting groups function
according to the following rules:
 The reporting priority is based on to group number sequence. From Group 1 Group
Group 2 Group 3 ….etc
 When more than one reporting destinations are assigned to a group, if a report is sent
to one of the detinations successfully, the system will stop reporting to the rest of the
reporting destination in the same group and move on to report to the next group.
If the Control Panel fails to send report to the first detination in a group, it will move on
to the next reporting destination. If all reporting destinations in the group cannot be
reached, the Control Panel will move on to the next group
If the Control Panel fails to report to all reporting groups, it will start reporting from group
1 and continue retrying until one report is made successfully.

16
5.3. Panel
This page is for you to configure panel settings.
Keyword
The Keyword is used for receiving commands from users. When a user sends a command
to the Control Panel, the correct keyword must be entered along with a valid User PIN
code for the Control Panel to recognize the command. The Keyword is disabled by default.
(MZ-8 only)
P-word
The P-word is also used for receiving commands from Installers. When an installer sends
a command to the Control Panel, the correct P-word must be entered along with Installer
code for the Control Panel to recognize the command. The P-word is “PROG” by default.
(MZ-8 only)
AC Fail Report
This is for you to set the waiting time for the Control Panel to make report after detecting
AC failure. Factory default is set to 5minutes.
Jamming Report
This is for you to set whether the Control Panel should detect radio frequency interference
and make report when interference is detected. Factory default is set to On. When radio
jamming is detected, the Control Panel will report the event accordingly.
Auto Check-in
This is for you to set the interval time the Control Panel waits before making a regular
check-in report

17
 Interval: Set the interval waiting time
 Offset Period: This is to set the time delay before the first “Auto Check-in Report”
report to be made. For example, if “Offset” time period is set to 2 Hours, then the
Control Panel will make the first “Auto Check-in Report” report after 2 hours,
High Temp.
This is for you to set the High Temperature reporting threshold. If the Control Panel has
learnt in a Temperature Sensor, it will make High Temperature report and raise alarm when
the temperature exceeds the threshold. When the temperature drops below set value
again, the Control Panel will stop alarming and send High Temperature Restore report.
Factory default is set to Disable.
Low Temp
This is for you to set the Low Temperature reporting threshold. If the Control Panel has
learnt in a Temperature Sensor, it will make Low Temperature report and raise alarm when
the temperature drops below the threshold. When the temperature rises above set value
again, the Control Panel will stop alarming and send Low Temperature Restore report.
Factory default is set to Disable.
Bypass Fault:
This is for you to set whether you want to ignore fault events regarding Ethernet or RF
function. Bypassed fault events will not displayed under Control webpage or cause the
fault LED will to light up and emit beeps. Please refer to 9. Panel Control for more
information regarding system fault event management.
 IP: When IP is selected, Ethernet related faults will be ignored.
 RF: When RF is selected, RF related faults will be ignored.
Factory default is set to Disable.
After finishing the above settings, press “Submit” to confirm the change.
Time Zone
This is for you to set your Time Zone.
Date & Time
This is for you to set your current date and time.
After finishing Time Zone and Date/Time setting, press “Adjust Time” to confirm the change.
Reset
Press the “Reset” button to restart the Control Panel.
Factory Reset
Press the “Factory Reset” button to clear all stored information and settings in the Control
Panel, all settings will be returned to factory default. You can choose to tick the box for
“Keep Network Setting” or “Keep Device Setting” before pressing Factory Reset to keep
part of the settings unchanged.

18
5.4. Area
This page is for you to configure area settings.
Final Door
 Final Door On: When the system is Away Armed with a Door Contact set to Entry
attribute, the system will automatically arm the system once the Door Contact is closed
even if the entry delay timer has not expired yet.
 Final Door Off: When the system is Away Armed with a Door Contact set to Entry
attribute, the system will only arm the system after the entry delay timer expires.
 Factory Default is set to Final Door Off.
Arm Fault Type
 Confirm: When set to Confirm, If you attempt to arm when a fault exists within the
system, the arming action will be prohibited, and a message will be displayed “Fault
exists! Please Confirm!” You need to arm the system again to confirm your action and
arm the system. (Factory Default)
 Direct Arm: When set to Direct Arm, If you attempt to arm when a fault exists within
the system, the system will enter selected arm mode without further notification about
fault events.
 Factory Default is set to Confirm.
Tamper Alarm
 Away Arm: Tamper alarm will only be activated when tamper switch is triggered under
Away Arm mode (Tamper event will still be reported normally in Home/Disarm mode).
 Always: Tamper alarm will be activated whenever tamper switch is triggered.
 Factory Default is set to Away Arm.
Entry Delay
Set the Entry Delay Timer for Away Arm, Home Arm 1, Home Arm 2, and Home Arm 3
modes. When a device set to Entry attribute is triggered under arm mode, the Entry Delay
Timer will begin to countdown. The system must be disarmed before the timer expires or
an alarm will be activated.

19
Factory default is set to 10 seconds.
Exit Delay
Set the Exit Delay Timer for Away Arm, Home Arm 1, Home Arm 2, and Home Arm 3
modes. When you arm the system, the system will enter your selected arm mode after the
Exit Delay Timer expires
Factory default is set to 10 seconds.
Alarm Length
When an alarm is activated, both the Control Panel siren and external siren will raise
alarm according to the Alarm Length setting.
Factory default is set to 3 minutes.
Supervision Timer
Set the supervision timer for accessory devices, if no supervision signal is received within
set duration for a certain device, the Control Panel will report the situation accordingly.
Factory default is set to 12 hour.
Sound Setting
 Door Chime: If not disabled, the Control Panel will sound a door chime sound when a
Door Contact set to Entry attribute is activated in Disarm mode. .
 Entry Arm: If not disabled, the Control Panel will sound beeping sounds when a Door
Contact set to Entry attribute is activated in Away Arm mode. .
 Entry Home: If not disabled, the Control Panel will sound beeping sounds when a Door
Contact set to Entry attribute is activated in Home Arm mode. .
 Exit Arm: If not disabled, the Control Panel will sound beeping sounds when during
Exit Delay Timer for Away Arm mode.
 Exit Home: If not disabled, the Control Panel will sound beeping sounds when during
Exit Delay Timer for Away Arm mode.
 Warning Beep: If not disabled, the Control Panel will sound beeping sounds every 30
seconds when fault exists within system.