Controls MVP-62110 User manual

.
Copyright @ Controls, Inc
P.O. Box 368 • Sharon Center, OH 44274
Phone [phone] • Fax [phone] • www.controlsinc.com
Product Manual
Pump Display & Control Panel
Mechanical Engines
Part Number: MVP-62110
Revision: 1.0

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
2
TABLE OF CONTENTS
INSTALLATION INFORMATION……...........………………………………...……………………………………………………………....2
MODULE CONNECTOR ……..........................………………………………...………………………………………………………………….4
PANEL CONNECTOR…………………………………………………………………..……………………………………………………………5
ENGINE ALARMS, CODES AND MESSAGES………………………………………………………………………….…...……..6
ALARM ANNUNCIATION AND CODE READER
PANEL INDICATION LAMPS
CONTROL PANEL ANALOG AND DIGITAL INPUTS……………………………………………………………………..…8
MENU SYSTEM……………………………………………………………………………………………..…………………………………….……10
MENU ACCESS, EXIT AND NAVIGATION
MENUS TO VIEW INFORMATION
MENUS TO CONFIGUREMODULE SETTINGS

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
3
INSTALLATION INFORMATION

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
4
MODULE CONNECTOR INFORMATION
BATTERY +
CAN HIGH
CAN LOW
MAG P/U +
FUEL LEVEL INPUT
BATTERY -
BATTERY -
E-STOP INPUT
FUEL / RUN
TEMP INPUT
OIL PRESS INPUT
PREHEAT OUTPUT
ALARM OUTPUT
1
2
3
4
5
6
1
2
3
4
5
6

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
5
ENGINE HARNESS CONNECTOR INFORMATION
Engine Harness Connector –Deutsch 21 pin (HDP24-24-21PE)
21 Pin Engine Harness Connector
Pin
Function
E
Battery Positive
G
Battery Negative
B
Fuel Hold
W
Pre Heat
D
Crank Signal
H
Oil Pressure Sender Input
J
Engine Temperature Sender Input
K
MPU-
S
MPU+ or Tach Input
A
Alternator Excite
R
Fuel Level or Aux Switch Input
N
Switched B+
P
Switched B+
X
Digital Input / Auxiliary Shutdown
C
Throttle Up
L
Throttle Down
14 Pin Accessory Harness Connector
Pin
Function
A
Battery Negative
B
Key On Power
C
Fuel Level
D
Alarm Output
E
External Shutdown

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
6
CONTROL PANEL SPECIFIC ALARMS AND SHUT DOWNS
The panel has its own engine safety alarms and shut downs that can be enabled. These alarms and
shut downs are managed by the control panel. The available options are listed below and can be
accessed via the Engine Safety Configuration menu.
Each alarm must be enabled in the Engine Safety Configuration menu to activate.
Heading
Default
Range
Units
Sender Check Bypass
0:10
0:05 –1:00
Min:Sec
Fuel Level Check
Off
Off / Always / Run
Low Fuel Pre Alarm
20
0 - 100
%
Low Fuel Alarm
1
0 - 100
%
Fuel Alarm Delay
0:05
0:01 –1:40
Sec
Oil Pressure Check
Run
Off / Always / Run
Low Oil Press Pre Alarm
6
0 - 100
PSI
Low Oil Press Alarm
5
0 - 100
PSI
Oil Press Alarm Delay
0:10
0:01 –1:40
Sec
Temperature Check
Run
Off / Always / Run
Low Temp Pre Alarm
0
0 - 300
Deg F
Low Temp Alarm
0
0 - 300
Deg F
High Temp Pre Alarm
244
150 - 300
Deg F
High Temp Alarm
245
150 - 300
Deg F
Temp Alarm Delay
0:10
0:01 –1:40
Min:Sec
Battery Volts Check
Off
Off / Always / Run
Low Battery Pre Alarm
12.0
0.0 –40.0
Volts
Hi Battery Pre Alarm
15.0
0.0 –40.0
Volts
Over Speed Check
Off
Off / Always / Run
Over Speed Alarm
3000
650 - 5000
RPM
Over Speed Alarm Delay
0:05
0:01 –1:40
Min:Sec
1) Off / Always / Run –Describes when the parameter will be monitored for alarm conditions. Run
refers to when the engine is running. Off disables the alarm conditions. Always enables the alarm
constantly regardless of engine state.
2) Alarm Delay –The time period, after Sender Check Bypass, that the parameter must be on the
alarm condition before the alarm becomes latched.

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
7
Indicator Lamps
.
Engine
Fault
Lamp
Engine
Alarm
Lamp

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
8
CONTROL PANEL ANALOG AND DIGITAL INPUTS
The panel has one analog input and up to one digital inputavailable to monitor other components,
sendersor signals. These inputs can be used for a number of purposesincluding alarms and shut
downs.
Input
Heading
Default
Options
Connector
Pin
Digital 1
Normally
Open
Open / Closed
B
1
Function
None
Message
None
Check
Off
Off / Always / Run
Digital Outputs
1) Alarm –Engine shutdown when active with display message as assigned. A red lamp will also
be illuminated.
2) Pre Alarm –Warning message will be displayed along with a yellow lamp when active.
3) Pre Alarm & Alarm - Energizes an external audible alarm when a pre alarm or alarm condition
is present. Pressing the ENTER button will silence.
4) Alarm Horn - Energizes an external audible alarm when an alarm condition is present.
Pressing the ENTER button will silence.
5) Engine Run - Relay will be active when engine RPM is greater than 600. Typically used to
drive an auxiliary circuit such as louvers or send a signal to a monitoring station.
6) Low Oil Press Alarm - Relay closes if a low oil pressure shutdown is detected.
7) High Coolant Temp Alarm - Relay closes if a high engine temperature shutdown is detected.
8) Over Speed Alarm - Relay closes if an over speed shutdown is detected.
9) Over Crank Alarm - Relay closes if an over crank alarm is detected.
10) Low Fuel Level Alarm - Relay closes if a low fuel level shutdown is detected.
11) Fuel / Run - Relay will be active during an engine start request and while the engine is
running.
12) Custom 1 - Reserved for OEM applications.
13) Preheat - Relay will be active during programmed preheat period. Used to drive a preheat
relay.

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
9
Digital Function Activation
1) Off / Always / Run –Describes when the parameter will be monitored for alarmconditions.
Run refers to when the engineis running. Off disables the alarmconditions. Always enables
the alarm constantly regardless of engine state.
2) AlarmDelay –The time period, after Sender Check Bypass, that the parameter must be on
the alarmcondition before the alarmbecomes latched.

CONTROLS, INCORPORATED
C O N T R O L S Y S T E M S & S O L U T I O N S
10
MENU SYSTEM
To Enter Menu System
Hold MENU button and press ENTER button.
Menu Navigation
Press MENU button to scroll menu options.
Press UP arrow button to enter menu.
Press DOWN arrow button to reverse.
Exit Menu System
Hold MENU button and press ENTER button.
To Change a Setting
Press ENTER button to bring up brackets [ ].
Press UP arrow button and DOWN arrow button to change setting.
Press ENTER button to make selection, brackets disappear.
Recycle key to the OFF position after changing a setting.