Cree XSP Series User manual

CI379X41R0
1 of 2
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
XSP Series
LED Wall Pack
Includes: XSPW™ Luminaires
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. To reduce the risk of electrical shock, turn off power supply before
installation or servicing.
2. This luminaire must be installed in accordance with the NEC or your local
electrical code. If you are not familiar with these codes and requirements,
consult a qualied electrician.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
WALL MOUNTING
STEP 1:
Remove mounting box from the luminaire. See
Figure 1.
STEP 2:
IMPORTANT – If needed, the (2) Keyhole
knockouts located inside box may be removed,
but are for alignment only. See Figure 2.
Luminaire is to be supported by (4) 3/16"
mounting holes. The Mounting holes will
accommodate a #10 bolt. Select appropriate
customer supplied mounting hardware for
mounting surface. See Figure 2 and 4.
STEP 3:
Place mounting box over junction box or
conduit. If mounting over junction box a 2-1/2"
Inspection knockout hole is included. See
Figure 2 and 4.
STEP 4:
For surface wiring (4) 1/2" threaded holes are
available. See Figure 2 and 4.
STEP 5:
If mounting on a uneven surface, place a
minimum of a 1/4" bead of high grade silicone
on the black gasket encompassing the
Inspection Knockout hole on the back of the
mounting box. See Figure 4.
STEP 6:
If mounting over surface mounted conduit
use the knockout conduit openings located
on the top, bottom, or sides of the luminaire.
Knockouts can be removed by using a hammer
or pliers. See Figure 3.
STEP 7:
Before securing to wall mounting surface,
make sure mounting box is level.
STEP 8:
Secure mounting box to wall.
TO INSTALL:
1
Mounting Box
2
(2) Keyhole
Knockouts
(4) 1/2" threaded holes
(4) Mounting Holes
(4) Mounting
Holes
Conduit Knockout
3
Luminaire Mount
Screws
Conduit Knockouts Locations
Slots on Luminaire
Housing

CI379X41R0
2 of 2
www.cree.com/lighting
© 2018 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See
http://lighting.cree.com/warranty for warranty and specifications. Cree® is a registered trademark, and the
Cree logo and XSPW™ are trademarks of Cree, Inc.
ELECTRICAL CONNECTIONS
STEP 1:
Make the following Electrical Connections to the terminal block:
a. For 120/277V connect the black fixture lead to the voltage supply
lead (Hot 1 for 208/240V wiring).
b. For 120/277V connect the white fixture lead to the neutral supply
lead. (Hot 2 for 208/240V wiring).
c. Connect the green or green/yellow ground lead to the green lead.
d. For Dimming; connect the violet dimming positive lead to the
supply dimming positive lead. If dimming is not being used cap
off the violet lead.
e. For Dimming; connect the grey dimming negative lead to the
supply dimming negative lead. If dimming is not being used cap
off the grey lead.
STEP 9:
Make wiring connections per the
Electrical Connections section.
NOTE: Once electrical
connections have been made,
insure that all wires are carefully
positioned so that no wires are
pinched between the mounting
box and the housing gaskets.
STEP 10:
Place luminaire on mounting box
by sliding the luminaire so that
the (4) Luminaire Mount Screws
on the mounting box are at the
end of each slot in the housing.
See Figure 3.
STEP 11:
Tighten (4) Phillips screws and
verify luminaire is secure.
7.0"
6.0"
Mounting
2.4"
Mounting
3.4"
4
(4) Mounting Holes
for 3/16" Customer
supplied Screws
Keyhole Knockouts- Provided for
Alignment Over Junction Box ONLY
1/2" Conduit Knockout
2-2/12" Inspection Knockout Hole for
Mounting Over Recessed Junction Box