Cree Essentia fp series User manual

1 of 2 LPN00336X0001A0_B

FP SERIES- LED FLAT PANEL

INSTALLATION INSTRUCTIONS

FP14, FP22, FP24 Luminaires

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant l’installation.

2. This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these

codes and requirements, consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n’êtes pas familier avec ces codes et

ces exigences, veuillez contacter un électricien qualié

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

TBAR MOUNTING

STEP 1

• Locate desired position for fixture in ceiling grid.

STEP 2

• Remove appropriate ceiling panel.

STEP 3

• Place the fixture into the T-bar ceiling panel

location. Fold out (4) hanging clips in corners

of fixture and use clips to secure fixture to grid.

Ensure that state and local codes are followed.

See Figure 1.

• NOTE: ** Not intended for use with 9/16” T-Bar

grids unless used with a 9/16” accessory clip like

“Armstrong® LFC- Fixture Clip” which can be

purchased through distribution. Consult factory

for non-standard grid applications. See Figure

STEP 4

• Make wiring connections per the Electrical Con-

nection section on the back page.

SUSPENDED MOUNTING

STEP 1

• For installation of suspended mount application

refer to installation instruction provided with in

the suspended mount kit, FPAC-45-1.

LUMINAIRE INSTALLATION

1(4) Hanging Clips

Armstrong® LFC- Fixture Clip to

use for 9/16th applications.

2 of 2 LPN00336X0001A0_B

See lighting.cree.com/warranty for warranty and specifications. Cree®and Essentia®are registered

trademarks of Cree, Inc. Armstrong® is a registered trademark of AWI Licensing LLC.

US: lighting.cree.com T (800) 236-6800 F (262) 504-5415

Canada: www.cree.com/canada T (800) 473-1234 F (800) 890-7507

0 - 10V DIMMING OPTION

STEP 1

• Remove the junction box cover by removing screw and

set screw aside to reinstall later. Bring in power supply

to the junction box using appropriate knockouts. If dim-

ming is being used, bring dimming conduit into dimming

wire compartment using appropriate knockouts. See

Figure 3.

STEP 2

• Make wiring connections per the “Electrical Connec-

tions” section.

STEP 3

• Once all leads are connected, carefully tuck the leads

inside the junction box and reinstall cover that was

removed in Step 1 above making sure not to pinch any

wires.

Junction Box Cover

Screw

Power Wire Compartment

(5) Power Wire

Knockouts

(2) Dimming Wire

Knockouts

Dimming Wire

Compartment

FCC NOTICE

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will