Cree Edge XAKE Series User manual

THE EDGE®
LED High Output Luminaire
Includes: XAK1, XAKE and XAKG Series
1 of 4 CI380X05R4_B
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
TO INSTALL:
TENON MOUNT
NOTE: Tenon must be 3.75" or longer and
constructed of steel.
STEP 1:
To adjust the angle of the luminaire,
reference the Angle Adjustment Section.
STEP 2:
Route the supply wire through the tenon.
Secure the supply wire to keep from sliding
back down the pole.
STEP 3:
Make electrical connections per Electrical
Connection section.
NOTE: Electrical Connections can be made
after installation is finished.
STEP 4:
Fit the luminaire over the tenon.
STEP 5:
Using 3/16" Allen wrench, hand tighten (2) set
screws, on the side of the tenon where the
cord is, until tip of screws engage tenon. (Do
not fully tighten). Torque set screws to 180 in.
lbs. (4.5 N-m) See Figure 1.
STEP 6:
Using 3/16" Allen wrench, hand tighten (2)
set screws, on the opposite side of the tenon
where the cord is, until tip of screws engage
tenon. (Do not fully tighten). Torque set
screws to 180 in. lbs. (4.5 N-m) See Figure 2.
DO NOT over-tighten.
12
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. This luminaire must be installed in accordance with the NEC or your local
electrical code. If you are not familiar with these codes and requirements,
consult a qualied electrician.
Ce produit doit être installé conformément à NEC ou votre code
électrique local. Si vous n’êtes pas familier avec ces codes et ces
exigences, veuillez contacter un électricien qualié.
3. Ensure the mounting surface is capable of supporting the weight of the
luminaire after installation.
Veiller à la surface de montage est capable de supporter le poids du luminaire
après l’installation.
4. If NEMA Photo Control is installed refer to NEMA Receptacle Section for
instructions.
5. Due to the weight of the luminaire, 2 people may be necessary during
installation.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
Tighten these (2) Set
Screws FIRST
Cord
Tighten these (2) Set
Screws LAST
• Prior to installation, store luminaire in a dry
location protected from rain, dust, and outdoor
environment. If equipped with a photocell
receptacle, do not store or install luminaire
outdoors without immediately installing a
suitable photocell, shorting cap, or other
compatible device. Do NOT leave receptacle open
to environmental elements. Luminaires with a
top-mounted photocell receptacle should not be
installed in an up-light position or at a tilt greater
than 45 degrees from the down-light position.

2 of 4 CI380X05R4_B
SURFACE MOUNT
STEP 1:
Using the provided mounting plate, mark the
intended installation surface with the bolt
pattern. Bolt hole diameter is 0.332". See
Figure 3.
STEP 2:
Using (4) 5/16"-18 customer supplied
fasteners grade 5 or better secure the fitter
to the mounting surface. See Figure 4.
STEP 3:
Route the supply cord from the luminaire
through the Fitter. See Figure 4.
STEP 4:
Mount luminaire to fitter using (4) 3/8"-16
supplied fasteners. See Figure 4.
STEP 5:
Make electrical connections per Electrical
Connection section.
DIRECT MOUNT TO POLE
STEP 1:
Using the provided mounting plate, mark the
pole with the bolt pattern. Bolt hole diameter
is 0.332". See Figure 3.
NOTE: Bolt hole diameter may be increased
to 9/16" for round poles. Verify clearance with
other pole hardware prior to drilling.
STEP 2:
Insert the Square Mounting Plate into the top
of the pole as seen in Figure 7.
STEP 3:
Using (4) 5/16"-18 supplied fasteners secure
the fitter to square mounting plate.
STEP 4:
Route the supply cord coming from the
luminaire through the Fitter and then through
the pole. See Figure 7.
STEP 5:
Complete Steps 4 and 5 of the Surface Mount
Instructions.
UPLIGHT MOUNTING
STEP 1:
Remove (2) 3/8” - 16 X 1.5” hex bolts located
in the top section of the Mounting Clamp. See
Figure 5.
STEP 2:
Remove Mounting Clamp and flip the
luminaire so that the LEDs are pointing
upwards. See Figure 5.
STEP 3:
Reinstall the Mounting Clamp, ensuring that
the (2) hex bolts are installed on the same
side as the LEDs. See Figure 6.
STEP 4:
Retighten the (2) hex bolts that were removed
in Step 1 to 150 in. lbs. See Figure 6.
STEP 5:
Install luminaire to mounting surface
referencing mounting procedures above.
2X
2.625
66.68
5.000
127
3.000
76.20
2.500
63.50
1.500
38.10
2X 1.000
25.40
0.50
12.70
2X 1.313
33.34
PLATE
HEIGHT
DRILL
DIAMETER
POLE
CENTER LINE
PLATE WIDTH
34
Fitter
(4) 5/16"-18
Customer Supplied
Fasteners
(4) 3/8"-16
Supplied Fasteners
Supply Cord
56
(2) 3/8" - 16 X 1.5" Hex Bolts
Mounting Clamp
Mounting Clamp
(2) 3/8" - 16 X 1.5" Hex Bolts
NOTICE: LEDs are
Pointing Upwards

3 of 4 CI380X05R4_B
ANGLE ADJUSTMENT
NOTE: Angle adjustment can be made before luminaire
installation.
STEP 1:
After the luminaire is installed, the angle of the luminaire can
be adjusted approximately 90° up or down in 5° increments.
STEP 2:
To adjust the angle, loosen the (2) 3/8" – 16 X 1.5" hex bolts
located in the top section of the Mounting Clamp. See Figure 8.
NOTE: Do NOT remove hex bolts.
STEP 3:
Using the Angle Bracket, shown in Figure 8, as a guide rotate
the luminaire to the desired position and retighten the bolts
loosened in Step 2 to 150 in.-lbs.
LATERAL ADJUSTMENT
STEP 1:
The position of the luminaire can also be adjusted laterally. To
adjust the Lateral position, loosen (2) 3/8" – 16 X 1.5" hex bolts
located in the top section of the Mounting Clamp. See Figure 8.
NOTE: Do NOT remove hex bolts.
STEP 2:
Remove the Angle Bracket and (2) screws and set aside. See
Figure 8
STEP 3:
The Angle Bracket can be secured using the existing holes on
the luminaire bar. Set the Mounting Clamp to desired lateral
adjustment using the following positions on the bar
(See Figure 9):
• Position 1 - Left justification.
• Position 3 - Center position (when angle bracket is on
the left side of the mounting clamp).
• Position 6 - Center position (when angle bracket is
on the right side of the mounting clamp).
• Position 8 - Right justification.
NOTE: Positions 2, 4, 5 and 7 will not be able to be used.
NOTE: Mounting two luminaires to a 24" Bullhorn Tenon will
require one luminaire mounted in position 1 and one luminaire
mounted in position 8.
STEP 4:
Once desired position is achieved reinstall the Angle Bracket
using (2) screws that were removed in Step 2.
STEP 5:
Retighten hex bolts that were loosened in Step 1 to
150 in-lbs.
NEMA®RECEPTACLE (OPTIONAL)
NOTE: Nema receptacle should only be used when mounting
clamp is in horizontal position.
STEP 1:
DO NOT loosen/tighten pan head screws for the NEMA
receptacle.
STEP 2:
Rotational adjustment of the photo control is tool-less.
STEP 3:
Engage/install photo control into NEMA receptacle on top of the
fixture.
STEP 4:
Firmly rotate photo-control with its photo-eye
approximately in the ‘N’ north direction. Some photo-
controls operate best somewhere between NW and NE.
Mounting
Clamp
Angle
Bracket
Angle Markings
Hex Bolts
Numbers on angle bracket are shown for illustration purpose
only. Actual bracket doesn’t show numbers.
Washers Square Mounting
Plate
(4) 5/16”-18
Supplied Fasteners
7
8
9
4321 8765
Angle Bracket is Shown in Position 3 in This Illustration
Mounting Clamp
Fitter
Nuts
Supply Cord

4 of 4 CI380X05R4_B
www.creelighting.com
© 2019 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is
subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree®and the Cree logo are registered
trademarks of Cree, Inc. THE EDGE®is a registered trademark of Cree Lighting, A company of IDEAL INDUSTRIES. NEMA® is a
registered trademark of the National Electrical Manufacturers Association.
ELECTRICAL CONNECTIONS
STEP 1:
Make the following Electrical Connections to supply cord:
a. For 120/277/347V connect the black fixture lead to the
voltage supply position of the terminal block or Hot 1 (for
208/240/480V wiring).
b. For 120/277/347V connect the white fixture lead to the
neutral supply position of the terminal block or Hot 2 (for
208/240/480V wiring).
c. Connect the green or green/yellow ground lead to the
green wire position of the terminal block.
d. If Dimming is an option; connect the violet dimming
positive lead to the supply dimming positive lead.
e. If Dimming is an option; connect the grey dimming
negative lead to the supply dimming negative lead
LINE
OR HOT 1
GREEN
LINE-BLACK
GROUND-GREEN
NEUTRAL-WHITE
DIM (-) GREY
DIM (+) VIOLET
NEUTRAL
OR HOT 2
VIOLET
GREY
SUPPLY WIRING
(DIMMING OPTIONAL)
LUMINAIRE
FIELD ADJUSTABLE DIMMING - OPTIONAL
STEP 1:
This luminaire may be provided with field adjustable dimming.
Luminaires leave the factory adjusted to the maximum setting
which is Position 9 as shown in Figure 10.
STEP 2:
Locate the luminaires electrical label and verify the luminaires
LED count and the maximum current available.
STEP 3:
The Dimming module is located inside the Mounting Clamp
on the Terminal Block Bracket. Remove (4) 8-32 Phillips
head screws that secure the Mounting Clamp Cover to
the Mounting Clamp and set aside. See Figure 11.
STEP 4:
Remove the mounting clamp cover exposing the wire connections
and set aside. See Figure 11.
STEP 5:
Remove the terminal block bracket by removing the (1) 8-32
Phillips head screw and set aside.
STEP 6:
Establish the desired input power multiplier by referring to
the product dimming spec sheet and turn the switch to the
correlating position.
STEP 7:
Adjust the Dimming Module to the selected position, replace the
terminal block bracket and the Mounting Clamp Cover ensuring
no wires are pinched and reinstall the screws that were removed
in Step 3.
10
Mounting Clamp
Cover
(4) 8-32 Phillips
Head Screws
11