Crux RVCVL-82S User manual

2014-2015 S60 / V60
2014-2015 S80
2014-2015 V70
2014-2015 V40 / V40 Cross Country
2014-2015 XC60
2014-2015 XC70
1. Features like lane pilot, distance assistant and city safety system, DO NOT work while the
RVCVL-82S is activated.
2. Tap the green wire to +12V to activate the video-in-motion feature in selective mode.
VL-82S
Harness
RVCVL-82S
CAN Interface
1
050415

Switch off ignition and disconnect the vehicle’s battery! If disconnecting the battery has to be avoided
according to the factory directive, it is usually sufficient to put the vehicle is sleep-mode.
In case the sleep-mode does not work, disconnect the battery with a resistor lead.
DIP Switch Setting
Navigation
DIP
1
DIP
2
DIP
3
DIP
4
DIP
5
DIP
6
Vehicles WITHOUT extra equipment (lane pilot,
distance assistant, city safety system) and rear-view
camera
ON ON OFF OFF ON ON
Vehicles WITHOUT extra equipment (lane pilot,
distance assistant, city safety system) and with rear-
view and front-camera
ON ON ON OFF ON ON
Vehicles WITH extra equipment (lane pilot, distance
assistant, city safety system) and rear-view camera
OFF ON OFF OFF ON ON
Vehicles WITH extra equipment (lane pilot, distance
assistant, city safety system) and with rear-view and
front-camera
OFF ON ON OFF
ON ON
VL-82S Harness
071715
2 / 6

DIP switch functions of the RVCVL-82S
DIP 1 – Activate Video in Motion
DIP 2 – Activate rear-view camera
DIP 3 – Activate front-camera
DIP 4 – No function
DIP 5 – CAN-bus termination resistor on the vehicle side
DIP 6 – CAN-bus termination resistor on the head-unit side
PIN Assignment of loose wires on the VL-82S Harness (8-Pin Molex)
Wire Color
Pin-No.
Assignment
●Green
Pin 6
Activation of the video-in-motion function
(+12V =Video in Motion, only if DIP1=OFF)
●White
Pin 2
Reverse Trigger Output (+12V DC 500 mA)
Only if DIP2=ON and Reverse gear engaged
Note: The interface is installed on the backside of the navigation unit.
CONNECTING THE CAN INTERFACE TO THE FACTORY NAVIGATION UNIT
VL-82S
Harness
RVCVL-82S
CAN Interface
071715
3 / 6

Connect female 8-Pin Molex connector of the VL-82S harness to the male 8-Pin Molex
connector of CAN Interface.
Transfer the female Quadlock connector of vehicle harness from rear of the head-unit
to male Quadlock connector of the VL-82S harness.
Plug female Quadlock connector of the VL-82S harness into male Quadlock
connector on the rear of the head-unit.
Connect the video RCA of the rear-view camera to the female RCA connector of the
adapter cable from the RVCVL-82S kit.
Connect the green Fakra plug of the adapter cable from the RVCVL-82S kit to the brown
Fakra socket of the head unit.
Connect the white wire of the VL-82S harness to the camera power supply (+12V max
500mA). The white wire gets power when reverse gear is engaged.
VL-82S Harness
CONNECTIONS TO REAR VIEW CAMERA
Back of radio
071715
4 / 6

CONNECTION TO FRONT CAMERA
Connect the video RCA of the front camera to the female RCA connector of the adapter
cable from the RVCVL-82S kit.
Connect the grey 5pin plug of the adapter cable from the RVCVL-82S kit to the grey 5pin
socket of the head unit.
Activation of rear-view and front camera
The rear-view camera activates automatically whenever the reverse gear is engaged. The
camera will be deactivated once a speed of 12 mph is reached. Alternatively, activation /
deactivation can be done manually via the camera menu or via the softkey (see diagram).
The front camera can only be activated / deactivated manually via the camera menu or via the
softkey (see diagram).
Softkey rear-view camera function:

rear-view camera

off

...
Softkey front- and rear-view camera function:

rear-view camera

front camera

off

...
071715
5 / 6

Camera menu
Softkey
Activation of the video-in-motion function
The video-in-motion can be activated and deactivated by DIP 1 or by the loose green wire on
the harness when connected to a +12V ACC source.
Video-in-motion permanent
With DIP1 to ON the video-in-motion function is activated permanently without disturbing the
navigation performance.
Video-in-motion selective
With DIP1 set to OFF, the green wire is used to activate and deactivate the video-in-motion
function.
Connect a switch between the green wire and +12V ACC.
●+12V = Video-in-motion is activated
●0V = Video-in-motion is not activated
071715
6 / 6