Crux RVCCH-75B User manual

INTERFACING SOLUTIONS
RVCCH-75B
REAR-VIEW & FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
DODGE
2014 - 2015 Durango
2014 - 2015 Ram*
JEEP
2014 - 2015 Grand Cherokee
APPLICATION NOTES:
FOR UCONNECT 5” AND 8.4”
DISPLAYS
This interface does not oer the
Force RVC feature.
PARTS INCLUDED
(1) CH-75B RVC Interface Module
(1) CH-75B FVC Interface Module
(1) CH-75B 52-Pin T-Harness (2663)
(1) Instruction Sheet
SAFETY PRECAUTIONS
1. Please read through the entire instruction manual before starting any of the installation procedures.
2. We recommend disconnecting the negative side of the battery until ready to code the vehicle.
3. Do not install any of the main modulesnear any major components or near the HVAC system,
as placing items near the HVAC maycause damage oroverheating to the interface.
4. We recommend not disconnecting any of the air bag connections behind the dash panels.
5. Thisproduct is under Crux’s 1 year manufacturer’s warranty. Warranty may be voided in the case where
the device shows proof of being opened or improper extreme force.
TECH SERVICES
All our products are manufactured under strict quality control. Each device is being tested before shipment. If nevertheless do occur problems or if
you have technical questions, contact us directly:
Crux Interfacing Solutions TechSupport
1(855) 822-1348 (Mon - Fri - 9:00 AM - 5:00 PM) Pacic Time
www.cruxinterfacing.comRev. 051016 1
*NOTE: Not compatible with diesel powered RAM trucks

INTERFACING SOLUTIONS
RVCCH-75B
REAR-VIEW & FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
INSTALLATION OVERVIEW
www.cruxinterfacing.comRev. 051016 2
8-PIN
(male plug)
FRONT CAM INPUT
(female plug)
WHITE / 12 OUTPUT (FRONT)
VIDEO
(male plug)
FRONT CAMERA
(not included)
BLACK/
GROUND
RED/
POWER
12V
GRAY/ REVERSE 12V
52-PIN
(female plug)
TO FACTORY
RADIO
52-PIN
(male plug)
REAR CAMERA
(NOT INCLUDED)
RED/ POWER 12
BLACK/ GROUND - TAP BLACK WIRE ON 8-PIN
VIDEO
(male plug)
4 5 6
ON
1 2 3
STATUS LED’S
4 5 6
ON
1 2 3
ACTIVATE
REAR-VIEW
& FRONT VIEW
8-PIN
MODULE
12-PIN
(male plug)
STATUS LED’S
DIP 1 = OFF
2 = ON
3 = OFF
4 = ON
5 = OFF
DIP 6 = ON
12-PIN
(male plug)
SWITCHER
GREEN/ VIDEO IN-MOTION ACTIVATE
REAR CAMERA
INPUT
(female plug)
OPTIONAL /
TOGGLE SWITCH
ENABLEDISABLE
Make sure to set dip switch number 2
is turned to ON.
Dip 2 = RVC Enable
DIP SWITCHES OVERVIEW
NOTE: GREEN WIRE AND DIP 1 HAVE
THE SAME FUNCTIONALITY. IF ONE IS
BEING USED THERES NO USE FOR THE
OTHER

INTERFACING SOLUTIONS
RVCCH-75B
REAR-VIEW & FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
www.cruxinterfacing.comRev. 051016 3
CONNECTING THE INTERFACE
Follow these steps to properly install the CAN module
Step 1 - Remove the factory display to gain accessto the factory 52-Pin (RED) connector.
Located behind the display, not the radio. Remove the factory 52-Pin connector.
Step 2 - Using the provided 52-Pin T-Harness, mate both sidesof the harness, to the factory harness and the factory display.

UP=ON DOWN=OFF
INTERFACING SOLUTIONS
RVCCH-75B
REAR-VIEW & FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
www.cruxinterfacing.comRev. 051016 4
CONNECTING THE INTERFACE
Follow these steps to properly install the CAN module
Step 3 - Connect both the 8-Pin and 12-Pin connectors to theircorresponding interface.
The 8-PIn is the only one withdip switches.Make sure all your connections are rmly inserted.
Step 4 - After connecting the module, set dip switches number “2”, “4”, and “6” to the “ON” position.
Make sure to test Front and Rear inputs.
All other dip switches are not to be used.
DIP SWITCH DESCRIPTION
IF NOT USING THE INPUT, PLACE TO OFF
DIP1 = ON = Video In-Motion Enable
DIP2 = ON = Rear-View Camera Enable
DIP3 = Not Used
DIP4 = ON = Front-View Button Activation
DIP5 = Not Used
DIP6 = CAN Termination
After each change of the DIP switch settings,
we recommend powering down the module,
then restarting thevehicle.
LED INDICATORS
BLUE LED:
SOLID = BUS RECOGNIZED
BLINKING = NO BUS DETECT
The Blue LED will shut o when
car enters sleep mode.
LED INDICATORS
RED LED:
ON = Power On
OFF = Power OFF

INTERFACING SOLUTIONS
RVCCH-75B
REAR-VIEW & FRONT-VIEW CAMERA
INTEGRATION INTERFACE FOR
DODGE & JEEP VEHICLES 2014-UP
www.cruxinterfacing.comRev. 051016 5
CONNECTING THE REAR-VIEW CAMERA
In order to activate the Rear-View Camera feature, make sure Dip switch number 2 is set to “ON”.
Step 5 - Make note that the Rear-View Camera is not included and canbe purchased separately.
Connect the RED power 12V cable from the camera to the GRAY Reverse (12V) trigger on the T-Harness.
Tap the BLACK wire onthe T-Harness 8-Pin connector for the GROUND to the camera.
Be sure to test the camera by placing the vehicle in REVERSE and conrming the camera display.
GRAY/ REVERSE 12V
52-PIN
(male plug)
REAR CAMERA
(NOT INCLUDED)
RED/ POWER 12
BLACK/ GROUND - TAP BLACK WIRE ON 8-PIN
VIDEO
(male plug)
4 5 6
ON
1 2 3
4 5 6
ON
1 2 3
ACTIVATE
REAR-VIEW
& FRONT VIEW
8-PIN
MODULE
12-PIN
(male plug)
STATUS LED’S
DIP 1 = OFF
2 = ON
3 = OFF
4 = ON
5 = OFF
DIP 6 = ON
REAR CAMERA
INPUT
(female plug)