3-PIN
(female plug)
TO FACTORY
RADIO
TO FACTORY
HARNESS
24-PIN
(male plug)
With voice dial activated the
vehicle will lose TUNE DOWN
on the SWC
10-PIN
(male plug)
TO ENABLE
VOICE DIAL
ON
1 2 3 4 5
3-PIN
(male plug)
22-PIN
(female plug)
22-PIN
(male plug)
MIC
INTERFACING SOLUT IONS
INTERFACING SOLUTIONS
BLUETOOTH CONNECTIVITY FOR SELECT CHRYSLER, DODGE VEHICLES 2011-UP
CHRYSLER
2011 - 2013 300
DODGE
2011 - 2014 Charger
2014 - 2014 Durango
2013 - 2014 Journey
Vehicles listed above must have the “WHITE”
22-Pin connector.
Radio type does not matter.
Applications are subject to change
without notice.
BEECR-35C work. Following these instructions from “Start” to” Finish” will ensure
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) CR-35C Interface Module
(1) CR-35C T-Harness
(1) Instruction Sheet
(1) Microphone
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
during the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
PRELIMINARY:
Please read the entire manual before installing this interface.
THIS INTERFACE STREAMS THE HANDS-FREE & MUSIC (A2DP)
THROUGH THE TWO FRONT SPEAKERS ONLY.
MOUNTING THE MICROPHONE
1. Insert the mounting clip into the ball joint on the microphone.
2. Mount the clip on your visor or near the rear view mirror.
3. Route the remaining cable along the edge of the roof liner and
towards the back of the radio, hiding the cable from sight.
INSTALLING THE INTERFACE
1. Remove the factory radio from the dashboard.
2. Remove the factory connectors from behind the factory radio.
3. Mate the interface connections to the factory connectors.
Make sure the 22-pin connector is properly seated into the interface.
4. Route the microphone to your desired location. Recommended area
is above the rear-view mirror.
INITIAL PAIRING
1. Turn on the vehicle and wait 15 seconds until the interface
announces “Please Select Your Mobile Phone” and Enter “0000”
2. From your mobile phone, choose and connect to the “Beeline”
device using the password “0000”.
3. The interface will announce “Pairing Successful” then
“Phone Connected” after the pairing process is complete.
Note: The Bluetooth interface will remember up to the last 8 devices.
power back on to re-attempt, if unsuccessful please contact our tech
support line.
AUTO RE-CONNECT
The BEELINE module will automatically re-connect the previously
paired mobile phone when the ignition is turned “ON” to the vehicle
and the mobile phone’s Bluetooth feature is also on.
Note: The Bluetooth module will re-connect with the last mobile
phone it was paired with. If no mobile phone is found, it will
revert to the pairing process.
RADIO CONTROL
There is no Bluetooth control on the factory radio.
All controls are done from the steering wheel controls.
STEERING WHEEL CONTROLS
All Bluetooth functionality is done on the steering wheel controls.
INSTALLATION OVERVIEW
3-PIN
(female plug)
TO F ACTOR Y
RADIO
TO F ACTOR Y
HARNESS
24-PIN
(male plug)
10-PIN
(male plug)
3-PIN
(male plug)
22-PIN
(male plug)
22-PIN
(female plug)
MIC
INTERFACING SOLUTIONS
INTERFACING SOLUTIONS
ENABLE VOICE DIAL AND MENU STRUCTURE
Rev. 051315
SEEK UP
SEEK DN
VOL UP
VOL DN
BACKSIDE CONTROLS
All functionality are done on the steering wheel controls.
MODELS LISTED BELOW MUST
BE EQUIPPED WITH SWC.
WHITE 22-PIN
R
MUSIC STREAMING
A2DP WORKS ONLY
ON F ONT SPEAKERS
3-PIN
(female plug)
TO F ACTOR Y
RADIO
TO F ACTOR Y
HARNESS
24-PIN
(male plug)
ON
1 2 3 4 5 6
MIC
CAN
BOX
BLUETOOTH
MODULE
12-PIN
(male plug)
Place DIP switch 1 to ON. (As shown below)
TO ENABLE VOICE DIAL:
NOTE:
If Voice Dial is enabled, the SWC function will change as follows:
1. A short press (tap) of the TUNE DOWN button will perform a“SEEK”.
2. A long press of the TUNE DOWN button will activate the Voice
Dial command on the paired phone.
Siri Voice command may not respond
properly. Standard Voice command
may have to be used instead.
