Dahua ARA10-W User manual

1
Wireless Siren
Quick Start Guide
V1.0.0

Tableof Contents
1Overview .................................................................................................................. 1
2Product Appearance.................................................................................................. 1
3Device Installation..................................................................................................... 2
4Usage ......................................................................................... 错误!未定义书签。
Appendix 1 Technical Specifications................................................................................... 4

Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
Do not expose the device to lampblack, steam or dust. Otherwise it may cause
fire or electric shock.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to humid environment. Otherwise it may cause fire.
The device must be installed on solid and flat surface in order to guarantee
safety under load and earthquake. Otherwise, it may cause device to fall off or
turnover.
Do not place the deviceon carpet or quilt.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Do not place any objecton the device.
Do not disassemble the device without professional instruction.
Warning:
Please use battery properly to avoid fire, explosion and other dangers.
Please replace used battery with battery of the same type.
Do not use power line other than the one specified. Please use it properly.
Otherwise, it may cause fire or electricshock.
Special Announcement
This manual is for reference only.
All the designs and software here are subject to change without prior written
notice.
owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.


1
Before Use
1. Do not touch surface of the detector andthe lens, so as not to affect the sensitivity of
the detector.If you need to clean the detector and the lens, please turn off the power and
use a soft cloth dipping some water to do so.
2. Avoid using the device in an environment of large temperature change, otherwise it
will affect the performance of the product.
3. This product can reduce accidents, however there is no guarantee. For your safety, in
addition to proper use of the products, but also be vigilant in dailylife,.

1
1Overview
This Wireless Siren is a device which can generate warning signal via sound and flash.
When someone enter the armed zone, detector outputs alarm signal to wireless alarm
controller, and the controller outputs control signal to the siren wirelessly it generates
sound/flash signal for warning purpose.
Available model: ARA10-W.

1
2ProductAppearance
Structure and appearance of the wireless siren are shown in Figure 2- 1 and Figure 2- 2.
Figure 2- 1
Figure 2- 2
No.
Note
1
Wireless module
2
+12V power connector
3
Buzzer
4
Vandal-proof switch
5
Battery
6
LED

2
3DeviceInstallation
Warning:
Installation and debugging must be executed by professional staff. If you encounter
device failure, please do not open and repair the device, you shall contact its
after-sales department.
Avoid installation in environment with large magnetic field around.
Avoid installation in placeswith a large amount of metal objects.
Fixed with screw:
Step 1. Please open device package, follow Figure 3- 1. Use straight screwdriver to take
down device rear cover.
Figure 3- 1
Step 2. Follow 错误!未找到引用源。, dig three holes on wall, and insert expansion bolts
into the holes.

3
Figure 3- 2
Step 3. Face device rear cover to expansion with bolts, insert and fasten self-tapping
screw at ①and ②to fix cover on wall. If you want to have leaving-wall
vandal-proof function for the device, insert self-tapping screwalso at ③.
Step 4. Close device front cover component to complete.

4
Appendix1 TechnicalSpecifications
Parameter
Note
Carrier Frequency
433MHz
Transmitting Power
10dBm
Transmission
Distance
1000m (open space/no interference)
Sound Intensity
85dB, 1 meter
Strobe Frequency
Adjustable, max 60 times/min
Vandal-proof
Leaving-wall and case vandal-proof
Battery Life
1.5 years
Temperature and
Humidity
-10℃～50℃, < 95%
Installation Method
Wall mount and 4 X 2 electricity box installation
Dimensions
98*55*26mm（（L*W*T）
Weight
0.2kg
Note:
This manual is for reference only. Slight difference may be found in user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the finalexplanation of
us.
Please visit our website or contact your local service engineer for more
information.