dams DHBC User manual





 
 I 
4� 4

 
 

111


DHBC












DPDHD
Desk High Door Pack
22.01.2018
1
1

1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN
2
PHILLIPS ( PH2 ) OR POZI ( PZ2 ) SCREWDRIVER

Please check that you have all the panels!
3
1
Step 1
Place the hinges into
the pre drilled holes
on the inside face of
each door panel.
1
Please check that you have all the fittings!
1
DHDPD
RM-DOR066
LH DOOR PANEL
RM-DOR067
RH DOOR PANEL
RM-HGP011
Clip On Hinge Plate
110' Clip On - Soft Close Hinge
RM-HGE011
4
4
RM-LOK13
Door Latch
Door Lock
RM-LOK11
1
1
RM-SCR26
3.5x15mm Wood Screw
M4x22mm Handle Screw
RM-SCR25
4
10
RM-HDL009
96mm Bow Handle
2
RM-LOK12
Door Clip
1
RM-SCR37
4.0 X 20mm Wood Screw
4
2
Step 2
Attach the hinges
using the 3.5 x 15mm
wood screws, 2
screws per hinge.
4x
8x
DHDPD

4
5
Step 5
Attach handles to both
doors using the M4x22
screws.
3
Step 3
Attach the hinge plates to the pre drilled
holes on the inside face of the bookcase
side panels, these plates are fitted with pre
attached screws.
Ensure the plate is fitted as per diagram 1.
4x
4
Step 4
Attach both doors to the
bookcase. Diagrams 2 & 3
show how to lock the hinge
to the plate.
Always lock the top hinge
into place first before
repeating for all hinges.
EDGE OF BOOKCASE
Diagram 1
Diagram 2
Ensure the hook of the hinge
locates into the hinge plate.
Fasten the hinge to the plate
by applying pressure here.
4x
2x
Diagram 3

5
7
Step 7
Attach the door latch to the rear face
of the LH door.
See diagram 5 for fixing position to be
used for both standard double door or
combination units.
Fix the lock in place using the
remaining x 4x20mm wood screws.
6
Step 6
Insert the lock into the back face of the
RH door, the rosette should be place
over the exposed lock barrel on the
front face of the door.
Align the lock with the edge of the
door as shown in diagram 4.
Fix the lock in place using two of the
4x20mm wood screws.
8
Step 8
Attach the latch strike plate to the
underside of the bookcase top.
This should be fitted to the 2 pre
drilled holes and aligned with the front
edge of the bookcase top as shown in
diagram 6.
2x1x
1x 2x
1x 2x
EDGE OF DOOR
EDGE OF DOOR
CUPBOARD
STANDARD
DIAGRAM 4
DIAGRAM 5
DIAGRAM 6
EDGE OF TOP

6
DOOR ADJUSMENT AND ALIGNMENT
AB
C
D
B
A - SIDE ADJUSTMENT
B - HEIGHT ADJUSTMENT
C - DEPTH ADJUSTMENT
D - DOOR RELEASE BUTTON
TO ADJUST THE GAP BETWEEN DOORS
Apply equal adjustment to point A on all hinges.
Tighten to make the gap smaller.
Loosen to make the gap larger.
TO RE ALIGN SKEWED DOORS
Adjust point A on individual hinges to re align accordingly.
Tightening the top hinges will rotate the door clockwise.
Tightening the bottom hinges will rotate the door anti-clockwise.
TO ADJUST THE GAP BETWEEN DOOR AND TOP
Loosen all point B screws without removing them.
Once loose lift the door to close any gap.
Whilst the door is held in its preferred position
re tighten all point B screws again.
TO ADJUST THE GAP BETWEEN DOOR AND SIDE PANEL
Loosen point C screws on all hinges.
Slide the hinge to your preferred position
and re tighten point C screws.
TO COMPLETELY REMOVE DOORS ACTIVATE BUTTON D ON ALL HINGES
POWER TOOLS SHOULD NEVER BE USED FOR ANY ADJUSTMENTS