dams R1090TC User manual

1 2 3 4 5
1
R1090TC
1090mm Economy Single Door Tambour Cupboard
03.02.2020
Secondary Storage
ST-1090S
ST-1090B
ST-TBS
Z11ST
ST-2S

1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN
2

1
ST-1090S
2
ST-1090B
3
ST-TBS
4
ST-2S
5
Z11ST
TOP
PEG
BOTTOM
PEG
Please check that you have all the Components!
3
Pack Contents
1 x LH SIDE PANEL - ( RM-SID231)
1 x RH SIDE PANEL - ( RM-SID232 )
1 x PARTITION PANEL - ( RM-PRT017 )
1 x FEET KIT - ( RM-FIT251 )
1 x HARDWARE KIT - ( RM-FIT253 )
RM-SID231
RM-PRT017
RM-SID232
RM-BAC145
RM-BAS075 RM-TOP448
RM-SHE038
Pack Contents
1 x BACK PANEL - ( RM-BAC145 )
Pack Contents
2 x SHELF PANEL - ( RM-SHE038)
Pack Contents
1 x BASE PANEL - ( RM-BAS075 )
1 x TOP PANEL - ( RM-TOP448 )
Pack Contents
1 x TAMBOUR DOOR
2 x TAMBOUR TRACK
1 x TAMBOUR CARTRIDGE ( BASE )
1 x TAMBOUR CARTRIDGE ( TOP )
1 x DOOR STRIKE PLATE
1 x SLIDING DOOR TOP PEG
1 x SLIDING DOOR BOTTOM PEG

Fitting Bag
1
RM-FIT251
Adjustable Foot Outer
4Adjustable Foot Inner 4RM-SCR73
3.5 x 12mm Wood Screw
8
Fitting Bag
2
RM-FIT253
17
RM-WOW01
30mm Wood Dowel
RM-BLT006
24mm Quick fix pin
RM-CAM03
15mm Minifix Cam
RM-PIN007
Titus Pin
RM-BUN02
Titus Bung
RM-CFM02
70mm Confirmat
RM-SCR73
3.5 x 12mm Screw
17 22 15
888
Please check that you have all the fittings!
1
ST-1090S
4
Step 1
Join the top tambour cartridge to the straight
length of tambour track.
Ensure the tag on the cartridge is correclty
inserted into the groove on the bottom of the track
1 2
Step 2
Once joined insert the assembled track into the
recess on the top panel.
Gently tap with a rubber mallet if the
track is a tight fit.
Step 3
Join the base tambour cartridge to the straight
length of tambour track.
Ensure the tag on the cartridge is correclty
inserted into the groove on the bottom of the track
3 4
Step 4
Repeat Step 2 to insert the assembled track into
the recess on the base panel.

5
Step 5
Use the 3.5 x 12mm Screws
to secure the top tambour
cartridge into place.
6
Step 6
Use the 3.5 x 12mm Screws
to secure the base tambour
cartridge into place.
7
Step 7
Insert quick fix pins and wood dowels into the
pre drilled holes on the top as shown below.
RM-SCR73
Qty 3
RM-SCR73
Qty 3
RM-BLT006
Qty 8
RM-WOW01
Qty 8
5
8
Step 8
Insert wood dowels into the pre drilled holes
on the base as shown below.
RM-WOW01
Qty 8

6
9
Step 9
Insert Cams, quick fix pins and wood dowels into the pre
drilled holes on the LH side panel.
See diagram A for details on inserting the cam fittings.
10
Step 10
Insert Cams, quick fix pins and wood dowels into the pre
drilled holes on the RH side panel.
See diagram A for details on inserting the cam fittings.
11
Step 11
Insert Cams into the pre drilled holes on the partition.
See diagram A for details on inserting the cam fittings.
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A
RM-CAM03
Qty 7
RM-BLT006
Qty 5
RM-WOW01
Qty 4
RM-BLT006
Qty 5
RM-WOW01
Qty 4
RM-CAM03
Qty 2
RM-CAM03
Qty 2
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A

13
Step 13
Join the back panel and LH
side panel together and
tighten all cam fittings.
12
Step 12
Insert Cams, quick fix pins and wood
dowels into the pre drilled holes.
See diagram A for details on inserting the
cam fittings.
7
RM-BLT006
Qty 2
RM-WOW01
Qty 2
RM-CAM03
Qty 6
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A

8
15
Step 15
Attach the RH side panel to
the part built carcass and
tighten all cam fittings.
14
Step 14
Attach the partition to the
back panel and tighten all
cam fittings.

A
A
9
17
Step 17
Turn the unit onto its head ready to insert
the door panel, ensure you are working
on a clean dry surface to prevent any
accidental damage to floor or cupboard.
16
Step 16
Attach the top ensuring that
all pins and dowels
correctly locate into the
fixing points.
Note:
Cams shown at point A are
covered by the partition
panel but can be tightened
using the 4mm allen key
that has been provided.
18
Step 18
Insert the tambour door glide clips into each
top and bottom of the end section of tambour
( See diagram A ) and then insert the door
into the track in the top.
Diagram A

10
19
Step 19
Place the base panel onto the carcass ensuring
that the door locates into the track and the wood
dowels correctly fit into the pre drilled holes.
21
Step 21
Once the base is attached
lie the unit on its back and
attach the 4 adjustable foot
levellers.
Note:
These fittings are supplied
in 2 parts, firstly fix the
inner housing to the base
with the 3.5x12mm wood
screws before screwing on
the outer housing.
Once attached return the
unit to its upright position.
20
Step 20
Connect the base to the carcass using the
70mm confirmat screw.
BASE
RM-SCR73
Qty 16Qty 4Qty 4
ADJUSTABLE
FOOT
OUTER
ADJUSTABLE
FOOT
INNER
RM-CFM02
Qty 8

SHELF
23
Step 23
Insert the titus bung shelf
supports into the pre drilled holes
on the underside of each shelf.
Note:
Ensure the opening in the bung
aligns with the opening in the
edhe of the shelf.
See Diagram D
22
Step 22
Attach the plastic finishing trim to
the LH side panel. Remove the
backing from the adhesive strip and
ensure that the strip is aligned with
top and bottom of the LH side panel.
See diagrams A & B
Attach the door strike plate to the
RH side panel using the 3.5x12mm
wood screws, ensure you are
screwing through the countersunk
face and that the plate is correctly
inserted into the recessed slot.
See diagram C
11
Diagram C
Diagram A
Diagram B
RM-BUN02
Qty 8
Diagram D

12
25
Step 25
Insert the shelves into the
cupboard, ensure that the
shelf support bungs fully
engage into the shelf pin,
they may need to be lightly
knocked down to ensure the
fittings are fully engaged.
24
Step 24
Screw in the shelf fixing
pins, ensure the fixings
points are inserted at the
same height on both
partition and side panel.
Note:
there is a selection of fixing
points that can be used to
create different sized
openings.
RM-PIN007
Qty 8

1 2 3 4 56
1
R2140TC
2140mm Economy Single Door Tambour Cupboard
03.02.2020
Secondary Storage
ST-TBS
ST-2140S
ST-2140B
Z21ST
ST-2S ST-3S

1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN
2

1
ST-2140S
2
ST-2140B
3
ST-TBS
4
ST-2S
6
Z21ST
5
ST-3S
TOP
PEG
BOTTOM
PEG
Please check that you have all the Components!
3
Pack Contents
1 x LH SIDE PANEL - ( RM-SID229)
1 x RH SIDE PANEL - ( RM-SID230 )
1 x PARTITION PANEL - ( RM-PRT016 )
1 x FEET KIT - ( RM-FIT251 )
1 x HARDWARE KIT - ( RM-FIT252 )
RM-SID229
RM-PRT016
RM-SID230
RM-BAC144
RM-BAS075 RM-TOP448
RM-SHE038
Pack Contents
1 x BACK PANEL - ( RM-BAC144 )
Pack Contents
2 x SHELF PANEL - ( RM-SHE038)
Pack Contents
1 x BASE PANEL - ( RM-BAS075 )
1 x TOP PANEL - ( RM-TOP448 )
RM-SHE038
Pack Contents
3 x SHELF PANEL - ( RM-SHE038)
Pack Contents
1 x TAMBOUR DOOR
2 x TAMBOUR TRACK
1 x TAMBOUR CARTRIDGE ( BASE )
1 x TAMBOUR CARTRIDGE ( TOP )
1 x DOOR STRIKE PLATE
1 x SLIDING DOOR TOP PEG
1 x SLIDING DOOR BOTTOM PEG

Fitting Bag
1
RM-FIT251
Adjustable Foot Outer
4Adjustable Foot Inner 4RM-SCR73
3.5 x 12mm Wood Screw
8
Fitting Bag
2
RM-FIT252
20
RM-WOW01
30mm Wood Dowel
RM-BLT006
24mm Quick fix pin
RM-CAM03
15mm Minifix Cam
RM-PIN007
Titus Pin
RM-BUN02
Titus Bung
RM-CFM02
70mm Confirmat
RM-SCR73
3.5 x 12mm Screw
20 28 15
20 20 8
4
Step 1
Join the top tambour cartridge to the straight
length of tambour track.
Ensure the tag on the cartridge is correclty
inserted into the groove on the bottom of the track
Please check that you have all the fittings!
1
ST-2140S
1 2
Step 2
Once joined insert the assembled track into the
recess on the top panel.
Gently tap with a rubber mallet if the
track is a tight fit.
Step 3
Join the base tambour cartridge to the straight
length of tambour track.
Ensure the tag on the cartridge is correclty
inserted into the groove on the bottom of the track
3 4
Step 2
Repeat Step 2 to insert the assembled track into
the recess on the base panel.

5
6
7
RM-SCR73
Qty 3
RM-SCR73
Qty 3
RM-BLT006
Qty 8
RM-WOW01
Qty 8
5
8
RM-WOW01
Qty 8
Step 5
Use the 3.5 x 12mm Screws
to secure the top tambour
cartridge into place.
Step 6
Use the 3.5 x 12mm Screws
to secure the base tambour
cartridge into place.
*
Step 7
Insert quick fix pins and wood dowels into the
pre drilled holes on the top as shown below.
Step 8
Insert wood dowels into the pre drilled holes
on the base as shown below.

6
9
10
11
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A
RM-CAM03
Qty 7
RM-BLT006
Qty 5
RM-WOW01
Qty 4
RM-BLT006
Qty 5
RM-WOW01
Qty 4
RM-CAM03
Qty 2
RM-CAM03
Qty 2
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A
Step 9
Insert Cams, quick fix pins and wood dowels into the pre
drilled holes on the LH side panel.
See diagram A for details on inserting the cam fittings.
Step 10
Insert Cams, quick fix pins and wood dowels into the pre
drilled holes on the RH side panel.
See diagram A for details on inserting the cam fittings.
Step 11
Insert Cams into the pre drilled holes on the partition.
See diagram A for details on inserting the cam fittings.

13
Step 13
Join the back panel and LH
side panel together and
tighten all cam fittings.
12
Step 12
Insert Cams, quick fix pins and wood dowels into the pre drilled holes.
See diagram A for details on inserting the cam fittings.
7
RM-BLT006
Qty 5
RM-WOW01
Qty 4
RM-CAM03
Qty 12
CAM
EDGEEDGE
adjacent edge which has the smaller hole.
Insert the cam into the 'surface' hole with the arrow aimed at the
Diagram A

8
15
Step 15
Attach the RH side panel to
the part built carcass and
tighten all cam fittings.
14
Step 14
Attach the partition to the
back panel and tighten all
cam fittings.