dams Elev82Mono User manual

Elev82Mono - Back-to-Back Desks
EVMB-1200 |EVMB-1400 |EVMB-1600
ASSEMBLY
INSTRUCTIONS
Elev82Mono
Back-to-Back Desk
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Pack A & B:
2 x DESKTOPS
Pack E:
1 x CROSS BEAMS
Pack C & D:
2 x LEG FRAMES
01-05-2019

2
1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
1 x Pozi screwdriver 1 x 4mm Allen key 1 x 5mm Allen key
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E

PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Please check that you have all the components
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A & B:
2 x DESKTOPS
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK C & D:
2 x UNDER FRAMES
PACK E:
1 x CROSS BEAMS
1200mm = ED128T
1400mm = ED148T
1600mm = ED168T
Leg pack code = B2B-S-S-A
Cross beam code = B2B-S-S-B
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
FITTINGS SUPPLIED Size PCS
M6 x 16mm 16
M10 x 12mm 8
M10 x 20mm 16
Size PCS
Ø4 x 25mm 4
Ø5 x 20mm 36
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E

ELEV82MONO BACK-TO-BACK DESKS ASSEMBLY
1
Step 1
Unpack your new height
adjustable desk frame and place
on a at surface.
Insert the desktop end rails
into the frame cross sections.
3
Step 3
Step 2
2
Insert the right leg into the frame
and use 4 of the bolts supplied to
x into place.

4
Step 4
Insert the left leg at a 45°angle
before xing the leg in its upright
position with the other 4 bolts
provided.
5
Step 5
6
Step 6
Before connecting the legs to
the motor ensure that they are
at their lowest point. This will
mean that the desk is level when
rotated to its upright position.
Extend the frame to the required
length. Once at the desired
length tighten the grub screws
on the frame.

7
Step 7
It is now time to attach both of
the legs to the motor. Follow the
steps shown to secure the shaft
from the motor to the bayonet
xing on each leg.
8
Step 8
Repeat the steps 2 through 7 for
both desk frames.
There are two holes in each leg
of the frames, make sure these
are pointing inwards in order to
join the desks together.
LEFT LEG
RIGHT LEG

9
Step 9
Insert one of the supplied bolts into
the bottom hole on the leg frame
as shown. This will be to attach the
cross beam.
Step 10
10
Step 11
11
Insert the cross beam over the bolt
and raise it into the keyhole position.
Once in position, a second bolt will
be able to be inserted and both bolts
to be tightened as necessary.
NOTE
You should be able to still see some of the
thread of the bolt.
If the thread is not visible, loosen the bolt by a
few turns to leave a gap.

Step 12
12
Step 13
13
Once the cross beams are attached,
turn the desk over into its upright
position.
2 person lift, do not attempt to do
this without assistance, this could
result in injury or damage to the
product.
Now position the desktop onto
the framework ensuring that the
scalloped edge of the desktop is at
the centre of the frame.
Align the holes in the desktop end
rails with the pre-drilled holes on the
underside of the desktop.
Use the wood screws supplied to
attach the top to the frame, if you are
using a cordless/power driver make
sure it is on a low torque setting.
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
NOTE
Use Ø5 x 20mm wood screws to
attach the top to the frame.

Finally attach the desktop
controller to the underside of
the desktop using the wood
screws provided. If you are using
a cordless/power driver make
sure it is on a low torque setting.
There are pre-drilled holes on
either side of the top so the
controller can be attached to the
Left or Right of the desk.
Step 14
14
Your desk is now ready to be connected to the mains outlet.
Before you proceed with operating your new desk it is recommended that you perform a full
reset of the controller to calibrate the height of each leg.
This can be done using the following steps;
• Press button down for 3 seconds.
• Continue pressing the button until both columns are in lowest position.
• Keep pressing the button until control box makes 1 beep.
• When control box makes 1 beep, it is conrmed that reset has been completed and button
can be released.
• Now the desk is operational.
• If the desk is disconnected by accidently pulling out the plugs at the control box, motors,
handset, main power source
• or system status reach overload, overheat etc. then the desk must be reset.
• If the desk is powered off intentionally at the main power switch, then the desk does not
need to be reset.
Operating the desk
Press the button, to operate the desk for upwards running.
Press the button, to operate the desk for downwards running.
Step 15
15
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
NOTE
Use Ø4 x 25mm wood screws to
attach the controller to the top.