dams Elev82 Touch EVT-RET User manual

Elev82Touch - Return Desk
EVT-RET
EVT-1200 |EVT-1400 |EVT-1600
ASSEMBLY
INSTRUCTIONS
Elev82Touch
Return Desk
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Pack A:
1 x DESKTOP
Pack C:
1 x RETURN FRAME
Pack B:
1 x UNDER FRAME
Pack D:
1 x RETURN TOP
01-21-2019

2
1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
1 x Pozi screwdriver 1 x 4mm Allen key 1 x 5mm Allen key
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E

PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Please check that you have all the components
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A:
1 x DESKTOP
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK B:
1 x UNDER FRAME
PACK C:
1 x RETURN FRAME
PACK D:
1 x RETURN TOP
FITTINGS SUPPLIED
1200mm = ED128T
1400mm = ED148T
1600mm = ED168T
Leg pack code = ST-T-*
Return frame code = RT-KIT-*
Return top code = EDRT
Code to include sufx of colour ordered eg. Silver (S), White (WH) or Black (K)
*
Size PCS
M6 x 12mm 2
M6 x 16mm 10
M10 x 16mm 12
M10 x 20mm 16
Size PCS
Ø4 x 25mm 2
Ø5 x 20mm 24
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E

ELEV82TOUCH RETURN DESK ASSEMBLY
1
Step 1
Unpack your new height
adjustable desk frame and place
on a at surface.
Attach the cross rails to
the return leg using the M6
machine thread bolts.
3
Step 3
Step 2
2
Single desk frame
Return desk leg
Attach the control box to the
frame positioned between
the cross rails. Ensure the
connectors marked “M1”, “M2”,
“M3” and “H” are positioned
away from the leg to allow easy
access.

4
Step 4
Slide off the leg with the pre-
attached control box and replace
it with the return leg.
5
Step 5
6
Step 6
Insert the 2 desktop end rails
into the frame cross sections.
Standard leg
Return leg
Unfold both legs to their upright
position.

7
Step 7
Once the end rails have been
inserted into the cross rails,
tighten the 4 bolts at points A-D.
A
B
D
C
8
Step 8
Attach both of the larger feet to
the leg uprights using the 8 x
bolts provided
9
Step 9
Once the feet are attached, turn
the desk over into its upright
position.
2 person lift, do not attempt to
do this without assistance, this
could result in injury or damage
to the product.

10
Step 10
Assemble the remaining leg by rstly
unfolding the leg upright into its
vertical position.
Step 11
11
Insert the remaining end rail into the
frame cross sections and tighten at
points A & B.
A
B
Step 12
12
Attach the smaller foot to the leg
upright with the remaining 4 x
bolts provided.

Step 13
13
Step 14
14
Insert the remaining cross rails into
the leg and tighten the grub screws
at the required length.
Now the return leg has been
assembled turn the leg over into its
upright position.
If you cannot lift the leg, seek
assistance as not to cause injury or
damage to the product.

Step 15
15
Attach the return leg to the main desk frame and tighten the grub screws in the rails.
Extend the frame to your desired length (1200mm, 1400mm or 1600mm).
Right hand return Left hand return

Extend the frame to your desired
length (1200mm, 1400mm,
1600mm).
Once extended, tighten the grub
screws on the inside face of the
cross sections.
Now that your desk frame is
assembled you can proceed with
the wiring. Connect both end
legs to the control box, insert the
connectors into ports “M1” and
“M2”.
Step 16
16
Step 17
17
NOTE
Before proceeding, ensure
that the connector plugs are
connected properly.
You should have heard the
plugs click and lock into
place.

Connect the extender cable to
the remaining connector on the
return leg. Insert connector into
port “M3” on the control box.
You can now attach the desktop
controller. This connector plug
should be inserted into the port
marked “H” on the control box.
Step 18
18
Step 19
19

The desktop controller should be
positioned on the opposite side
of the desk to the return.
Insert the wire protector into the
recessed cut out in the top of
the cross section and ensure
the wire passes through the
protector.
You are now ready to connect
your mains lead to the control
box. Insert the gure 8 connector
plug into the corresponding
socket on the control box, this is
marker “AC”.
Step 20
20
Step 21
21
NOTE
Ensure that once the
controller is connected to
the control box all the wires
are neatly tucked into the
cable management clips.

Now position the desktop onto
the framework ensuring that the
scalloped edge is at the rear of
the frame.
Align the holes in the desktop
end rails with the pre drilled
holes on the underside of the
desktop.
Use the wood screws supplied
to attach the top to the frame, if
you are using a cordless/power
driver make sure it is on a low
torque setting.
Attach the second desktop
extension brackets to the
underside of the desktop, there
are pre-drilled holes for ease of
alignment.
Once attached, position the
return top onto the frame and x
in place ensuring that the outside
edge of both tops are aligned.
Step 22
22
Step 23
23
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
NOTE
Use Ø5 x 20mm wood screws to
attach the top to the frame.
NOTE
Use Ø5 x 20mm wood screws to
attach the top to the frame.

If the desktops are out of
alignment from the frame you
may need to loosen the grub
screws in the framework to
adjust the frame to the collect
length.
Finally attach the desktop
controller to the underside of
the desktop using the wood
screws provided. If you are using
a cordless/power driver make
sure it is on a low torque setting.
There are pre-drilled holes on
either side of the top so the
controller can be attached to the
Left or Right of the desk.
Step 24
24
Step 25
25
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
NOTE
Use Ø4 x 25mm wood screws to
attach the controller to the top.

Your desk is now ready to be connected to the mains outlet.
Before you proceed with operating your new desk it is recommended that you perform a full
reset of the controller to calibrate the height of each leg.
This can be done using the following steps;
• Press both buttons at the same time for 3 seconds.
• Continue pressing the buttons until both columns are in lowest position.
• Keep pressing the buttons until control box makes 1 beep.
• When control box makes 1 beep, it is conrmed that reset has been completed and buttons
can be released.
• Now the desk is operational.
• If the desk is disconnected by accidently pulling out the plugs at the control box, motors,
handset, main power source or system status reach overload, overheat etc. then the desk
must be reset.
• If the desk is powered off intentionally at the main power switch, then the desk does not
need to be reset.
Operating the desk
Press this button, to operate the desk for upwards running.
Press this button, to operate the desk for downwards running.
Step 26
26

Upgrading to the Digital control unit
Make sure that your height adjustable desk is turned off and unplugged from the mains.
Unplug the controller supplied with your height adjustable desk and replace with the digital
control unit. Fix this to your top using the wood screws provided.
After connecting the digital control unit you will need to perform a reset.
Reset
• Press both up & down buttons at the same time for 3 seconds. Continue pressing the buttons
until both columns are in lowest position. When the reset is nished, the control box makes a
beep and the buttons can be released.
• When conducting reset, the display shows “000” in last 100mm stroke. When the reset hsd
nished, the display shows starting height again.
• If releasing up & down buttons before the display shows ”000”, the desk goes back to normal
operation.
• Reset is necessary for rst operation of the desk.
Normal operation
• Press any button. 3-digits display shows current desk height in centimeters.
• Press up or down button to adjust the desk height.
• When no button has been pressed for 10 seconds, display goes off. Press any button to light
up the display again.
• When no button has been pressed for 30 seconds, the system goes to <0.1 W standby mode.
Long press any button to wake the system up. Display shows desk height again.
Memory position
The digital control unit supports 4 memory positions. to set the positions follow these steps;
1. Operate the desk to preferred height.
2. Press any of 1,2,3,4 buttons together with up or down buttons for 2 seconds to store the
current height. Display shows P1/P2/P3/P4 when the position has been stored.
3. Now, hold any of the 1,2,3 or 4 buttons until the desk reaches the stored height.
Stored postion can only be overwritten, not to be cleared.
Step 27
27