dams Elev82 Mono Single Desk EVM-1200 User manual

Elev82Mono - Single Desk
EVM-1200 |EVM-1400 |EVM-1600
ASSEMBLY
INSTRUCTIONS
Elev82Mono
Single Desk
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Pack A:
1 x DESKTOP
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Pack B:
1 x UNDER FRAME
01-05-2019

2
1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
1 x Pozi screwdriver 1 x 4mm Allen key 1 x 5mm Allen key
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E

PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
Please check that you have all the components
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK A:
1 x DESKTOP
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
PACK B:
1 x UNDER FRAME
1200mm = ED128T
1400mm = ED148T
1600mm = ED168T
Leg pack code = ST-T-S
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E
FITTINGS SUPPLIED Size PCS
M6 x 16mm 8
M10 x 16mm 8
M10 x 20mm 8
Size PCS
Ø4 x 25mm 2
Ø5 x 20mm 18
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E

ELEV82MONO SINGLE DESK ASSEMBLY
1
Step 1
2
Step 2
Unpack your new height
adjustable desk frame and place
on a at surface.
Place the frame on the
desktop and ensure that the
desktop controller passes
through the wire protector.
3
Step 3
Extend the frame to the required
length. There are pre-drilled
holes in the desktop will help you
gauge the length. Once at the
desired length tighten the grub
screws on the frame.

4
Step 4
Insert the end rails into the
desktop frame cross section.
5
Step 5
Insert the right leg into the frame
and use 4 of the bolts supplied to
x into place.
6
Step 6
Insert the left leg at a 45°angle
before xing the leg in its upright
position with the other 4 bolts
provided.

7
Step 7
Align the holes in the desktop
end rails with the pre-drilled
holes on the underside of the
desktop.
Use the wood screws supplied
to attach the top to the frame, if
you are using a cordless/power
driver make sure it is on a low
torque setting.
8
Step 8
Attach both feet to the legs using
the bolts provided.
9
Step 9
Make sure that both legs are
at their lowest point so that the
desk is level when it is rotated to
its upright position.
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
NOTE
Use Ø5 x 20mm wood screws to
attach the top to the frame.

10
Step 10
Attach the desktop controller to the
underside of the desktop using the
wood screws provided. If you are
using a cordless/power driver make
sure it is on a low torque setting.
There are pre-drilled holes
It is now time to attach both of the
legs to the motor. Follow the steps
shown to secure the shaft from the
motor to the bayonet xing on each
leg.
LEFT LEG
RIGHT LEG
Step 11
11
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D PACK E
NOTE
Use Ø4 x 25mm wood screws to
attach the controller to the top.

It is now time to lift the desk over into its upright position. This is a 2 person lift, do not attempt
to do this without assistance as this could result in injury or damage to the product.
Step 12
12
Your desk is now ready to be connected to the mains outlet.
Before you proceed with operating your new desk it is recommended that you perform a full
reset of the controller to calibrate the height of each leg.
This can be done using the following steps;
• Press button down for 3 seconds.
• Continue pressing the button until both columns are in lowest position.
• Keep pressing the button until control box makes 1 beep.
• When control box makes 1 beep, it is conrmed that reset has been completed and button
can be released.
• Now the desk is operational.
• If the desk is disconnected by accidently pulling out the plugs at the control box, motors,
handset, main power source
• or system status reach overload, overheat etc. then the desk must be reset.
• If the desk is powered off intentionally at the main power switch, then the desk does not
need to be reset.
Operating the desk
Press the button, to operate the desk for upwards running.
Press the button, to operate the desk for downwards running.
Step 13
13
PACK A
PACK A & B
PACK C & D
PACK B
PACK C
PACK D
PACK E