Dancover HGSA1010 User manual

05-08-2021
for
4,45x2,99x2,95m
Greenhouse
3,01x2,99x2,95m and
Manual

Greenhouse
Assembly Instructions
—— For Sliding Door
Walk-in Greenhouse
MODEL A (mm) B (mm) C (mm)
HGSA1010 3012 28492990
HGSA1410 4446
C
A
B

Complaints
2
Statement
May we congratulate you on buying new Greenhouse.
We feel sure that by following the detailed assembly instructions, you will find as much
pleasure in actually building the greenhouse as the many hours you will spend on your
greenhouse in the future. The assembly instructions are a combination of text and illustra-
tions and no technical knowledge is required for the erection of the greenhouse. The
frames are numbered and packed separately corresponding to the succession in the as-
sembly instructions
Assemble one section at a time. However, bolts and various fittings for all sections will be
found in pack of instructions.
Each pack is specified in the list of components. All detailed illustrations are marked with a
symbol.
Guarantee
We grant a comprehensive guarantee that covers replacement or repairs of defective parts
due to material or manufacturing fault. The guarantee does not cover transport, assembly,
freight etc. Glass is not covered by the guarantee.The guarantee is invalid if the greenhouse
is not assembled according to these instructions.
Winter Protection
Our greenhouse is constructed with frame dimensions up to 50% stronger than most of
the competing products. We still recommend you to protect your greenhouse during the
winter.
Supporting the roof ridge at the centre of the greenhouse.
Removing greater snow loads.
Taking precautions against snow falling down from, for instance a roof.
Preventing the wind from damage the greenhouse door and windows.
Foundation
The base is maintenance free and, of course, all fittings are included. Remember to order
concrete pipes and concrete at you local dealer, as these are not included in the delivery.
Maintenance
Grease doors, hinges and door track
Clean the gutter for leaves etc
Adjustment of windows
Replacement of broken glass
Clean the greenhouse with disinfectant before and after the growing season
We put severe demands on quality to secure that you get faultless products.
However, should a complaint occur, we kindly ask you to contact the dealer, from whom
you have bought the greenhouse, To secure a quick service you should specify the extent
of the defect by means of the list components in the assembly instructions.

3
Tips
The base has to be fastened in a non-freezing depth <80cm>.
The greenhouse is to be fastened to the base.
The base has to be 100% level and square. The easiest way to ensure this is
that the two diagonal measurements are identical.
We recommend greasing the screws for the doors for an easier assembly.
Glazing should only be carried out in fairly calm weather.
Make sure that the greenhouse is square before starting to glaze.
We recommend the frames to be degreased with acetone before glazing.
We recommend using working gloves while glazing.
An assistant make the job easier.
Tools
The greenhouse is assembled by means of the following tools:
Spirit level
Spanner/socket spanner 8 and 10 mm
Screw driver
Silicone pistol
Acetone for degreasing the frames
Please put on gloves avoid of slitting your hands.
Avoid of crashing the material, results in un-
shapes, it is not fits in fixture.
Avoid of materials cuts the polycarbonates
sheets.
Cautions

4
Base
A(mm) B(mm) Gable
profiles
(mm)
Side
profiles
(mm)
Anchor
legs Corner- ite Fixing tabs M6x10 M6 M6x10 Crop Washer
HGSA
1010 2958 2958 2x2958 2x2958 4411 32 43 11 8
HGSA
1410 2958 4392 2x2958 2x4392 6415 36 51 15 10
Gable Side
Base on grass
On brick without base
AB

5
Base
# m5
HGSA
1010 15
HGSA
1410 19
IMPORTANT Before assembling aluminium base, the end trough centers of four legs
should match both end trough centers of side sills and front & rear sills at the same time.
side sills
front & rear sills
Please match four corner
troughs together at the
same time

6
Gable
# 7601 7602 7603 7605 7024 7210 7213 7214 7606
Size 1922 2365 2365 2758 2896 2884 1656 1656 2008
QTY 211112112
# a1 a2 a3 G-m1 G-m2 a20G-p1
Size M6x10 M6 M6x15 ----
QTY 25 30 512301
1
7024
2
456
6
7
8
9
7601 76017602 76037605
7210
7210
7213 7214
7606 7606
3

7
4
5
7601
7210
a1
7210
7606
a1
7
7601
7213
a1
7210
G-m2
7606
87213
7602
a1/a2
9
a1/a2
7605
7213 7214
G-m1
12
3
6
7210
7602
a1
7601
7024
a3
7024
7602
7606
a3
7605
7024
a3
Gable

8
Side Rear
# 7032 7034 7024 7026 7607 7871 7210 7643 a1 a2 a3 a20
Size 2919 4353 2896 4330 1922 2033 2884 4318 M6x10 M6 M6x15 -
HGSA
1010 1132114 19 519
HGSA
1410 1152118 25 725
7032
7024
7607 7607
7871 7871
7607
7210
7034
7026
7871 78717607 7607 7607 7607
7643
7607
1
7607
Note: Please add extra bolt into channel for eave
cantilever use in advance.
7032/
7034
14
2
3
27607
7210/
7643
47032/
7034
7871
3
7607
7871
7024 a3

9
Side Front
# 7032 7034 7268 7641 7607 7020 7021 7871 7872 7873 a1 a2 a3 a20
Size 2919 4353 2896 4330 1922 1456 2856 2033 733 1450 M6x10 M6 M6x15 -
HGSA
1010 112112218 22 422
HGSA
1410 114112222 28 628
7032
7268
7034
7641
7607 7607
7871 7871
7872 7872
7871 7871
7607 7607 7607 7607
7873 7873
14
2
3
2
7607
7872/
7873
3
7607
7268
7871
a3
47032/
7034
7871
70207021
70207021
Section View
7020
7021
a1/a2
1
7021 7020
7032/
7034
7607
7021
7020
Note: Please add extra bolt into channel for eave
cantilever use in advance.