Dancover GH158011 User manual

29-12-2021
Manual
for
Commercial greenhouse tunnel
10x15x3,7m

Assembly Instructions

2
Dear customer / dear garden friend,
we congratulate you on purchasing a greenhouse.
You have chosen a high quality and stable greenhouse.
Please read the assembly instructions first.
Follow this step by step!
Storage / keeping
Store protected - Please store all components in a dry place and protected from direct
sunlight!
Parts list / packing list
Before you start to assemble the greenhouse, please use this description (material list) to
check that the components supplied are complete.
Each packaging unit goes through a quality control, which also includes checking the
respective quantities. Missing parts can thus be almost ruled out. If parts are still missing,
please tell us the wrong position.
The manufacturer assumes no responsibility for damage caused by improper assembly or
force majeure.
Note:
If possible, the greenhouse should be set up in a sheltered place and not in stormy
weather. It is dangerous to leave a partially assembled house!
The roof of the greenhouse must be free from snow loads greater than 10cm!
Safety regulations / intended use:
Protective gloves, safety shoes and suitable head protection must always be worn when
assembling polycarbonate sheets and greenhouse components.
This variant of a greenhouse is designed for growing plants and should only be used for
this. Any use beyond this is considered improper.
The operator / user of the greenhouse is solely liable for any resulting damage!

3
The construction of the greenhouse must be carried out by at least two people! Work with
safe, handcrafted tools.
Always work with gloves (risk of injury, risk of cuts)
This symbol describes the manual work, e.g. the assembly of components
You need the following tools to set up:
•Open spanner 13 mm
•Plastic hammer
•Tape measure 5m
•Spirit level (1m)
•Stepladder
•Cutter knife
•Cordless screwdriver

4
Frame
List of material:
Width: 10,00m
Lenght 16,50m
Note: The number of items in this material list corresponds to a greenhouse length
of 16.50 m.
If the greenhouse length is longer/shorter, the individual items will be adjusted
accordingly! See also delivery note!
Qty.
Part-No.
Designation
2.1
20,00
9081
Arch 1000
2.2
48,00
20007
Anchor 80cm
2.3
10,00
9220
Strut 7,00m
2.4
4,00
9241
Longitudinal tube 5,97m
2.5
4,00
9244
End piece 2,35m
2.6
33,00
9431
Longitudinal tube 1,40m
2.7
30,00
9433
Connector 1"
2.8
6,00
9434
Connector 1" for gable
2.9
70,00
14005
Screw: 8x50
2.10
4,00
9410
Connector
2.11
10,00
9412
connector 54er
2.12
16,00
9248
Cross pipe 1,98m
2.13
32,00
19004
Pipe clamp 2"
2.14
10,00
9533
S-Hook
2.15
44,00
20077
S-Hook, 6mm for. Film
2.16
10,00
9470
Spacer
2.17
1,00
9512
Chain tensioner
2.18
11,00
9481
Films Type 1000 transparent with wires
2.19
52,00
14005
Screw: 8x50
2.20
20,00
14006
Screw: 8x70
2.21
20,00
14007
Screw: 8x80
2.22
24,00
14008
Screw: 8x100
2.23
10 ,00
14009
Screw: 8x130

5
Foundation of your greenhouse
The stable and robust construction of the greenhouses allows them to be installed directly
on a level, pre-compacted surface.
The fastening is carried out with an earth anchor system and the film has to be buried.
Frame-assembling:
1.0
Angle the base
1.1
Tension cords alongside
1.2
Measure diagonally - distances must be the same
1.3
Check parallelism

6
2.0
Anchor / longitudinal tube
2.1
2.2
Set the anchor along the cord - for distance see 2.2
a. Push the longitudinal tubes through the eyelets of the anchor
b. Connect the longitudinal pipes to the pipe sections.
Note: The longitudinal tubes are 6m long, the start and end pieces are
shorter
2007
9241
9433
9434
150 cm
4cm
10,00 m
10,03 m

7
3.0
Arch assembling
3.1
3.1.1
Assemble left / right arch - using connector 54
Place spacer between archs and connector
Fix the arch left / right to connector with screw 4.8x19
NOTE: nut must point inward
9081
9412
14006
14101
3.1.2
Place strut and screw
NOTE: nut must point inward
9220
14007
3.1.3
Mount connector, center
NOTE: nut must point down
9433
9470
14009
3.1.4
Mount connector, right
NOTE: nut must point down
9433
14005
3.1.5
Mount connector, left
NOTE: nut must point down
9433
14005

8
4.0
Set up arch / frame
4.1
4.1.1
Set up pre-assembled frames in field 2
4.1.2
Push the pipe clamp left / right onto the frame
NOTE: The clamp leg must point inwards
19004
4.1.3
Screw the frame to the longitudinal tube
NOTE: - The nut must point inwards
14008
4.1.4
Set up pre-assembled frames in field 3
4.1.5
Push the pipe clamp left / right onto the frame
NOTE: The clamp leg must point inwards
4.2
Place cross tubes between frames 2 + 3 - use a spirit level and
align the frame
9248
4.2.1
Fix the cross tubes in place in the clamp
14005
14101
4.3
Mount the cross tubes on the opposite side
4.3.1
Repeat steps 4.1.2 to 4.2.1

9
4.4
Longitudinal pipes
NOTE - As soon as a frame is set up - mount the longitudinal tube
4.4.1
Mount the center tube
9431
14005
4.4.2
Mount the longitudinal pipe on the left
9431
14005
4.4.3
Mount the longitudinal tubes on the right
9431
14005
4.5
S-hook
4.5.1
Put the S-hook
9533