DANLERS EZ CESR Quick start guide

Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: [phone] Fax: [phone]
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Products available from DANLERS
• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products
Please call for more information or a free catalogue, or visit our website.
This product conforms to BS EN 60669-2-1, BS EN 55015 and BS EN 60730.
Please ensure the most recent edition of the appropriate local wiring regulations are observed
and suitable protection is provided (protected with the appropriate MCB) 1kV over voltage.
Please ensure that this device is disconnected from the supply if an insulation test is made.
This product is covered by a warranty which extends to 5 years from the date of manufacture.
Precautions and Warranty
15/09/16 INS311 EZ CESR
Variants
DANLERS design and manufacture other EasyZAPP Ceiling Flush Mounted
variants, coded by the following order codes:
EZ CESR 10VDC Suitable for 1-10VDC ballasts
EZ CESR DALI Suitable for DALI ballasts.
Troubleshooting
The load will not switch on:
•TheLUXsettingasspeciedbytheEasyZAPPAppissettoolowandisinhibiting
the switch.
• The moving body is not emitting more IR than the background.
(Person wearing insulating clothing in a warm environment)
• Person is too far from the PIR switch, see detection diagram.
• Person is moving unusually slowly (perhaps when testing).
• The control unit battery is not engaged (ON).
Switch RED dip switch next to the telejack connector on the EZ CESR
control unit towards the centre of the control (see diagram D).
The load switches on when nobody is present:
• Heater causing infra-red variations in a small cold room.
Resite the EZ CESR control away from heater.
• Please contact DANLERS for further technical support.
 EasyZAPPCeilingushmountedswitches
EZ CESR
EasyZAPP ControlZAPP ceiling surface passive infra-red occupancy switches can
be mounted directly onto solid ceilings or onto a range of different mounting boxes
(diagram A). EasyZAPP devices incorporate a passive infra-red quad sensor to detect
movement of a warm body within their detection zone (diagram B) and a photocell to
monitor the ambient light level.
PleaseNote:ALLadjustmentsaremadeviaafreelydownloadableEasyZAPP
AppavailablefromtheDANLERSwebsite.EasyZAPPproductscannotbe
conguredbyDANLERSControlZAPPorScheduleZAPPapps.
Upon detecting movement, if the ambient light is dark enough, the EasyZAPP device
will turn the load ON. The ambient threshold can be set to between approximately
30luxto1000luxandinnitelux(photocellinactive)viathe‘Brightness’settingson
the EasyZAPP App. If no more movement is detected within a pre-selected time as
determined by the EasyZAPP App, then the EasyZAPP device will turn the load off.
This‘Timeout’ortimelagcanbesetviatheEasyZAPPAppadjusterbetween10sec
and 23hrs 59min 59sec.
Loading
EZ CESR is suitable for mains switching or DALI switching only.
EZ CESR can switch up to:
• 10 amps (3000W) of resistive loads
• 6amps(1500W)uorescentlamps,highfrequencyorswitchstart,
incandescent or mains halogen lamps (recommended with integral safety fuse)
• 3 amps (750W) of electronic or wire wound transformers.
• 2 amps (500W) of low energy lamps: CFL, LED, 2D etc.
• 1 amp (250W) of fans or most metal halide lamps.
Start-upmodeandDefaultsettings
When the EZ CESR is powered up, it will take 1 minute for the circuitry to stabilise
(detectionLEDashing)andensuretheoutputisoff,theEasyZAPPdevicewillthen
enter its Default Operating Mode.
Please Note: When in the Default Operating Mode the EZ CESR is set up as
an occupancy switch with a 20 minute turn OFF timeout (time lag) and photocell
disabled.

Installation procedure
1. Please read these notes carefully before commencing work. In case of doubt
pleaseconsultaqualiedelectrician.Ensurewiresandcablesaresecurelyheld
within the connection terminals.
 IMPORTANT:TheEZCESRControlUnitclockbatterymustbeengaged(ON)
priortoinstallationbyswitchingtheREDdipswitch(seediagramE)tothe
DOWNposition.
2. POSITIONING: The EZ CESR switch should be installed to achieve correct
coverage of the area, see diagram B.
If the photocell override facility (enabled
via EasyZAPP app) is required, the switch must be located above an area where
daylightcangivegreaterilluminationthanthearticiallight.Avoidlocatingthis
product where it is exposed to drafty conditions (exposed lobbies, open ceiling
voids or near fans) or near heat sources. To cover large areas PIRs should be
spaced in a 5 metre grid formation.
3. Disconnect the PIR from the circuit before performing insulation testing of the
wiring circuit.
4. Do not connect on a circuit with large inductive loads, as induced spikes may
cause false triggering or damage the PIR.
5. EZ CESR must be connected to the EasyZAPP Power Supply (CZPS) via the
EasyZAPP communication cable (telejack) provided, for wiring see diagrams C and
D.
NOTE: The use of non EasyZAPP connectors may damage the EZ CESR or CZPS
and will invalidate the warranty).
6. Knockout or drill the appropriate holes on the mounting plate for attaching the plate
to the ceiling or back box (if applicable). Feed telejack through the appropriate (side
or rear) entry hole. Screw the back mounting plate to the ceiling or back box via the
mounting holes. Push the telejacj connector into the sensor head terminal. Push the
sensor head onto the mounting plate and align the side clips with the slots on the
sensor heads.
Settings and calibration
ALL settings are adjusted by EasyZAPP App as detailed in the free to download
EasyZAPP App User Guide, including:
Timeout: Adjustable time lag from 10 seconds to 24 hours.
Brightness: Adjustable switching threshold, 30 to 1000 lux and inactive. EZ CESR
must be calibrated as instructed on the user guide manual.
BatchCongure:ForconguringmultipleEZCESRcontrolswithidenticalsettings.
Name:For identifying individual controls.
Password: For security against accidental or malicious alteration.
Please visit www.danlers.co.uk to download the EasyZAPP user guide.
B:Detectiondiagram
up to 5m
up to 7m
Strong detection zone
i.e. person moving arm
or walking towards PIR Secondary detection
zone i.e. person
walking perpendicular
to PIR
For optimum coverage
recommended
mounting height: 2.4 to 5m
A:Mountingdiagram
Knock out mounting
holes or pre-drill
pilot holes.
For telejack entry from
above - knock out
central mounting hole
For side entry -
knock out side
mounting hole
Clip telejack into the device
then join device to mounting
plate via mounting clips
L
load
N
100 - 260 VAC
50 / 60 Hz
L
N
SL
L
load
N
100-260 VAC
50 / 60 Hz
L
N
SL
L
N
SL
L
N
SL
Several EZ CESR wired in parallel
Single EZ CESR
L
load
N
100 - 260 VAC
50 / 60 Hz
L
N
SL
L
load
N
100-260 VAC
50 / 60 Hz
L
N
SL
L
N
SL
L
N
SL
Several EZ CESR wired in parallel
Single EZ CESR
C:Wiringdiagram D:Wiringdiagram
D:Connectordiagram
Telejack connector
Control Unit
SL
L
L
N
Power Supply
Red dip switch (MUST be
switched towards centre of control)
to engage clock battery ON
IMPORTANT
ON