Deltech Fitness DF830 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF830
LAT ATTACHMENT
Assembly Manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF830
HARDWARE
QTY 1 DF830
INSTRUCTIONS
BOX CONTENTS
F
WEIGHT CARRIAGE
QTY 1
D
LOW BAR
QTY 1
C
LAT BAR
QTY 1
E
CABLE
QTY 2
J
4” FLANGE
QTY 2
I
PULLEY FLANGE
QTY 2
A
TOP FRAME
QTY 1
B
BOTTOM SUPPORT
QTY 1
G
REAR SUPPORT
TUBE
QTY 1
H
FRONT SUPPORT
TUBE
QTY 1

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
HARDWARE
K
K
4-1/2” PULLEY
QTY 3 3-1/2” PULLEY QTY 4
L10” CHAIN
QTY 2
N
QUICK CLIP
QTY 2
X
PULLEY BUSHING
QTY 6
M
SNAP HOOK
QTY 6
W
M12 x 75MM BOLT
QTY 4
O
M10 x 70MM BOLT
QTY 3
Q
M12 x 65MM BOLT
QTY 2
P
M10 WASHER
QTY 8
V
M10 LOCKNUT
QTY 7
T
M12 LOCKNUT
QTY 8
S
M10 x 45MM BOLT
QTY 4
R
M12 WASHER
QTY 14
U

TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
ATTACH THE BOTTOM SUPPORT (B) TO THE BOTTOM CROSSMEMBER OF THE POWER
RACK OR SMITH MACHINE YOU ARE INSTALLING TO USING M12 x 75MM BOLTS (O), 4”
FLANGE PLATES (J), M12 WASHERS (U) AND M12 LOCKNUTS (S). TIGHTEN SECURELY.
FRAME ASSEMBLY
(NOTE: THE NUTS USED ON THIS ARE
LOCKNUTS, THIS MEANS YOU MUST
TIGHTEN THEM DOWN PAST THE
PLASTIC INSERT.)
B
O
U
S
U
J

INSTALL THE REAR SUPPORT TUBE (G) TO THE BOTTOM SUPPORT (B) ALIGNING HOLES
IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (U) AND 12MM
NUT (S) AND TIGHTEN.
INSTALL THE FRONT SUPPORT TUBE (H) TO THE BOTTOM SUPPORT (B) ALIGNING HOLES
IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (U) AND 12MM
NUT (S) AND TIGHTEN.
FRAME ASSEMBLY
H
G
B
U
S

LOWER PULLEYASSEMBLY
F
INSTALL THE 4-1/2” PULLEY (K) INTO THE CENTER FLANGES OF THE BOTTOM
SUPPORT USING THE M10 x 45MM BOLT (R), 10MM WASHERS (V), AND M10 LOCK-
NUT (T).
INSTALL THE 3-1/2” PULLEY (L) INTO THE FRONT FLANGES OF THE BOTTOM
SUPPORT USING THE M10 x 45MM BOLT (R), 10MM WASHERS (V), AND M10 LOCK-
NUT (T).
M
T
V
V
R
K
L

INSTALL THE WEIGHT CARRIAGE ASSEMBLY ONTO THE REAR FRAME WITH THE
WEIGHT BAR FACING FORWARD. SLIDE DOWN UNTIL IT RESTS ON THE RUBBER
BUMPER.
FRAME ASSEMBLY
DISREGARD THIS STEP IF USING
WITH STACK LOADED ATTACHMENT

INSTALL THE 3-1/2” PULLEYS (L) INTO THE TOP FRAME (A) USING THE
PULLEY BUSHINGS (M), THE M10 x 70MM BOLTS (Q), AND THE M10 LOCK
NUTS (T).
T
TOP FRAME ASSEMBLY
M
A
M
Q
L

ATTACH THE FRONT OF THE TOP FRAME ASSEMBLY TO THE POWER RACK OR SMITH
MACHINE WITH M12 x 65MM BOLTS (P), M12 WASHERS (U), 4” FLANGE (J), AND
LOCKNUTS (S). HAND TIGHTEN ONLY
ATTACH THE BACK OF THE TOP FRAME ASSEMBLY TO THE FRAME SUPPORT TUBES
WITH M12 x 65MM BOLTS (P), M12 WASHERS (U), AND LOCKNUTS (S). SECURELY
TIGHTEN ALL BOLTS.
FRAME ASSEMBLY
PUUSOU
U
S
J

ASSEMBLE THE FLOATING PULLEY ASSEMBLY USING THE 4-1/2” PULLEYS (K), THE
PULLEY FLANGES (I), THE M10 x 45MM BOLTS (R), THE 10MM FLAT WASHERS (V), AND
THE 10MM LOCKNUTS (T).
FLOATING PULLEYASSEMBLY
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
K
R
V
V
T
I

THIS CHAIN ATTACHES BETWEEN THE END OF
THE CABLE AND THE MOUNTING FLANGE ON
THE FRONT SUPPORT. THE CHAIN ALLOWS FOR
CABLE LENGTH ADJUSTMENT
THIS CHAIN ATTACHES BETWEEN THE OTHER
END OF THE CABLE AND THE LOW ROW BAR.
CABLE INSTALLATION
NOTE: BOTH CABLES ARE THE
SAME LENGTH
STARTING WITH THE CABLE END WITHOUT THE BALL, INSTALL UPPER CABLE OVER
FRONT PULLEY, BACK TO MIDDLE PULLEY, DOWN TO TOP PULLEY OF FLOATING PULLEY
ASSEMBLY, UP TO REAR PULLEY AND DOWN TO WEIGHT CARRIAGE. ATTACH SNAP HOOK
TO END OF CABLE AND THEN TO WEIGHT CARRIAGE BRACKET. ATTACH SNAP HOOK TO
BALL END OF CABLE AND ATTACH LAT BAR.
STARTING WITH THE CABLE END WITHOUT THE BALL, INSTALL LOWER CABLE UNDER
FRONT PULLEY, BACK TO REAR PULLEY AND UP AND OVER LOWER PULLEY OF FLOATING
PULLEY ASSEMBLY. ATTACH SNAP HOOK TO END OF CABLE AND THEN TO ONE END OF
THE CHAIN. ATTACH SNAP HOOK TO THE OTHER END OF CHAIN AND THEN TO MOUNTING
FLANGE ON FRONT SUPPORT TUBE. ATTACH SNAP HOOK TO BALL END OF CABLE AND
ATTACH 10” CHAIN. ATTACH SNAP HOOK AND ROW BAR.
DISREGARD THIS STEP IF USING
WITH STACK LOADED ATTACHMENT

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM- PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT, DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE -ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED
PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES
AND LIABILITIES BECOME VOID.
SAFETY NOTICE