Deltech Fitness DF9500 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF9500
FLAT/INCLINE/DECLINE BENCH
Assembly Manual
Assembly Video Available
Simply scan the QR code below
on your phone’s camera to access
the video

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BOX CONTENTS
F
BACKREST
QTY 1
A
FRONT FOOT
QTY 1
B C
REAR FOOT
QTY 1
LEG PAD
QTY 2
E
SEAT
QTY 1
G
FRAME
QTY 1
BACKREST
SUPPORT
QTY 1
H
D
HOLDDOWN
QTY 1
SEAT SUPPORT
QTY 1
J
BACKREST
SUPPORT
QTY 1
K
LEG PAD TUBE
QTY 1
L DF9500
HARDWARE PACK
QTY 1
SLIDE ASSEMBLY
QTY 1
I

HARDWARE
[phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
SEAT SUPPORT PIN
QTY 1
T
M12 WASHER
QTY 12
Q
M10 WASHER
QTY 10
R
M12 LOCKNUT
QTY 6
S
M12 x 76MM BOLT
QTY 4
M
M10 x 25MM BOLT
QTY 12
P
M12 x 70MM BOLT
QTY 2
N
RUBBER SHOE
QTY 4
W
PULL-PIN
QTY 1
U
LOCK KNOB
QTY 1
V X
MUSHROOM CAP
QTY 2

NOTE: THE SEAM GOES
TO THE BOTTOM SIDE
ATTACH THE SEAT (F) TO THE SEAT SUPPORT (J) USING THE M10 x 25MM BOLTS (P) AND
M10 FLAT WASHERS (R).
ATTACH THE BACKREST (A) TO THE BACKREST SUPPORT (H) USING THE M10 x 25MM
BOLTS (P) AND M10 FLAT WASHERS (R). MAKE SURE THE SEAM ON THE BACKREST FACES
THE SEAT AS SHOWN ABOVE.
SEAT & BACKREST ASSEMBLY
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
P
R
P
R
F
A
J
H

W
C
W
W
B
N
Q
Q
S P
R
R
P
ATTACH THE REAR FOOT (C) TO THE FRAME USING THE M10 x 25MM BOLTS (P) AND M10
FLAT WASHERS (R). THEN SLIDE THE RUBBER BOOTS (W) ONTO THE REAR FOOT (C). DO
NOT TIGHTEN NUTS AT THIS TIME.
NOW ATTACH THE FRONT FOOT (B) TO THE FRAME (G) USING THE M12 x 70MM BOLTS (N),
THE M12 FLAT WASHERS (Q) AND THE M12 LOCK NUTS (S). SLIDE THE THE RUBBER
BOOTS (W) ON THE FRONT FOOT (B). DO NOT TIGHTEN NUTS AT THIS TIME..
FRAME ASSEMBLY
INSTALL THE PULL-PIN (U) AND LOCKING KNOB (V) INTO SLIDE ASSEMBLY (I). INSTALL THE
SLIDE ASSEMBLY (I) ONTO THE FRAME (G). LOCK INTO PLACE WITH PULL-PIN. INSTALL
PULL-PIN (U) INTO FRAME (G).
U
G
V
U
I
W

ATTACH THE BOTTOM OF THE BACKREST ASSEMBLY TO THE FRAME USING M12 x 76MM
BOLT (M), M12 FLAT WASHERS (Q), AND M12 LOCK NUT (S).
NOW ATTACH THE BACKREST ASSEMBLY TO THE TOP OF THE BACKREST SUPPORT (K)
USING M12 x 76MM BOLT (M), M12 WASHERS (Q), AND M12 NUT (S). THEN ATTACH THE
BOTTOM OF THE BACKREST SUPPORT (K) TO THE SLIDE ASSEMBLY USING M12 x 76MM
BOLT (M) , M12 FLAT WASHERS (Q), AND M12 LOCK NUT (S).
BACKREST INSTALLATION
BACKREST ASSEMBLY
K
M
Q
Q S
M
Q
Q S
S
Q
M Q

SEAT ASSEMBLY
LEG HOLD DOWN & SEAT INSTALLATION
ATTACH THE SEAT ASSEMBLY TO THE FRAME (G) USING M12 x 76MM BOLT (O), M12 FLAT
WASHERS (S), AND M12 LOCK NUT (U). (* NOTE THE TIGHTER YOU MAKE THE BOLT, THE
MORE SECURE THE BENCH WILL BE.)
INSERT THE LEG HOLD DOWN (D) INTO THE FRAME ASSEMBLY AND SECURE IT WITH THE
PULL PIN.
AT THIS POINT YOU WILL WANT TO MAKE SURE YOUR BENCH IS ON A FLAT SURFACE AND
TIGHTEN THE NUTS ON THE FRONT AND REAR FOOT.
NEXT YOU WILL WANT TO TIGHTEN THE NUTS ON THE SEAT AND BACKREST. THEY NEED TO BE
TIGTHENED ENOUGH TO REMOVE SIDE TO SIDE MOVEMENT, BUT NOT SO TIGHT THAT THE SEAT
AND BACKREST WILL NOT ROTATE.
D
M Q
Q
S

INSERT THE LEG PAD TUBE (L)THROUGH THE HOLD DOWN (D). NOW SLIDE THE LEG
PADS (E) ONTO THE LEG PAD TUBE. INSTALL MUSHROOM CAPS (X) INTO EACH END OF
LEG PAD TUBE AND HAMMER INTO PLACE WITH RUBBER MALLET.
LEG HOLD DOWN ASSEMBLY
X
E
L
E
X
D
ADJUST SEAT TO DESIRED ANGLE AND INSERT SEAT SUPPORT PIN (T).
T

ADJUSTING THE BACK PAD: RAISE AND LOWER THE BACKREST USING THE
PULL PIN. MAKE SURE THE PULL PIN IS SECURE IN THE ADJUSTMENT HOLE
AND THE KNOB IS TIGHTENED BEFORE USE.
ADJUSTING THE SEAT PAD: RAISE THE SEAT PAD TO THE DESIRED POSITION
BY USING THE PULL PIN THOUGH THE HOLES IN THE BRACKET.
ADJUSTING THE LEG HOLD DOWN: RAISE AND LOWER THE HOLD DOWN BY
TURNING THE PULL PIN AND PULLING IT TO ADJUST UP OR DOWN. WHEN
ADJUSTED MAKE SURE THE PULL PIN IS SECURE.
ADJUSTMENT

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE RISK OF INJURY CAN BE REDUCED BY ALWAYS FOLLOWING
THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ACCESSORIES ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE

WEIGHT BENCH ACCESSORIES
DF105 Add preacher curls to your bench with this
preacher curl attachment. Get more information at
www.fitnessdestination.com
DF106 Add leg extension and leg curls to your
bench with this leg attachment. Get more
information at www.fitnessdestination.com
DF1200 Add lat pulls to your bench with this lat
attachment. You can find more information at
www.fitnessdestination.com