Digital Projection Mercury Quad Series User manual

Rev A March 2017
Mercury Quad Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
117-787A

page i
Digital Projection Mercury Quad Series
Rev A March 2017
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless
the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2017 Digital Projection Ltd. All rights reserved.
Notes

page ii
Digital Projection Mercury Quad Series
Rev A March 2017
Risk Group 3 Information
Light hazard warning
Failure to comply with the following may result in serious injury:
• No direct exposure to the beam is permitted, RG3 IEC 62471-5:2015.
• Operators control access to the beam within the hazard distance or install the projector at sufcient height to prevent
exposures of spectators’ eyes within the hazard distance.
The hazard distance (Fig. 1) is the distance measured from the projection lens at which the intensity or energy per unit of surface is lower
than the applicable exposure limit on the cornea or skin. If the person is within the hazard distance, the beam is considered unsafe for
exposure.
Lens Part Number Hazard Distance
0.67 : 1 xed 105-607 0.47 m
1.12 : 1 xed 105-608 1.41 m
1.16 - 1.49 : 1 zoom 109-236 1.52 m
1.39 - 1.87 : 1 zoom 105-610 1.63 m
1.87 - 2.56 : 1 zoom 105-611 1.46 m
2.56 - 4.16 : 1 zoom 105-612 2.83 m
4.16 - 6.96 : 1 zoom 105-613 7.02 m
6.92 - 10.36 : 1 zoom 109-235 12.7 m
Notes
Fig. 1: hazard distance

page iii
Digital Projection Mercury Quad Series
Rev A March 2017
Light hazard labels on the body of the projector
Light hazard labelling is part of the product label.
1Product label
2Risk Group 3 label
3Hazard Warning symbol
4Not For Home Use logo
AC Input / Entrée CA (輸入 / 输入) : 200-240V 11.5A 50/60Hz
AC Input / Entrée CA ( 輸入 / 输入 ) : 110-130V 11A 50/60Hz
Model/Modèle (型號 / 型号): Mercury Quad WUXGA
DLP PROJECTOR / DLP Projecteur
( 數位投影機/数字投影机 )
警告:此為A 級產品，在生活環境中，該產品可能會造成無線電干擾。
在這種情況下，可能需要用戶對干擾採取切實可行的措施。
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient
aucune pièce interne réparable par l’utilisateur.
警 告 : 請勿打開外殼,設備內無服務性維修之元件
警 告 : 請勿打開外殼,設備內無服務性維修之元件
製造商:Digital Projection Limited
Greenside Way Middleton Manchester, M24 1XX UK 製造地:中國/製造地:中國 / Made in China
326XXXXXXX
Part No.:117-779
CAN ICE-3(A) / NMB-3(A)
Warning !
Do not look into the beam.
No direct eye exposure to the beam is
permitted.
RG3
Hazard Distance : 0-300cm
Avertissement !
Ne Pas Regarder Directement
Dans Le Faisceau.
L’exposition Directe Des Yeux Au
Faisceau Est Interdite.
RG3
Distance À Risque : 0-300cm
3
4
AC Input / Entrée CA ( 輸入 / 输入 ) : 200-240V 11.5A 50/60Hz
AC Input / Entrée CA ( 輸入 / 输入 ) : 110-130V 11A 50/60Hz
Model/Modèle (型號 / 型号): Mercury Quad WUXGA
DLP PROJECTOR / DLP Projecteur
( 數位投影機/数字投影机 )
警告:此為A 級產品，在生活環境中，該產品可能會造成無線電干擾。
在這種情況下，可能需要用戶對干擾採取切實可行的措施。
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution : Do not open the cover. No user-serviceable parts inside
Avertissement : ne pas ouvrir le couvercle. Le produit ne contient
aucune pièce interne réparable par l’utilisateur.
警 告 : 請勿打開外殼,設備內無服務性維修之元件
警 告 : 請勿打開外殼,設備內無服務性維修之元件
製造商:Digital Projection Limited
Greenside Way Middleton Manchester, M24 1XX UK 製造地:中國/製造地:中國 / Made in China
326XXXXXXX
Part No.:117-779
CAN ICE-3(A) / NMB-3(A)
Warning !
Do not look into the beam.
No direct eye exposure to the beam is
permitted.
RG3
Hazard Distance : 0-300cm
Avertissement !
Ne Pas Regarder Directement
Dans Le Faisceau.
L’exposition Directe Des Yeux Au
Faisceau Est Interdite.
RG3
Distance À Risque : 0-300cm
1
2
Notes

page iv
Digital Projection Mercury Quad Series
Rev A March 2017
Introduction
Congratulations on your purchase of this Digital Projection product.
Advanced compact High Brightness projector for large venue applications. Includes:
• High frame rate capability up to 120Hz.
• Sequential, Dual Pipe and Domestic mandatory formats for 3D.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• 3G-SDI with loop-through.
• Edge Blend including black level compensation.
• Geometry correction - Keystone, Cornerstone, Electronic Rotation, Pin/Barrel correction.
• Full non-linear warping via PC applcation.
• Blanking control for custom input window sizing.
• Control via LAN and RS232.
• Motorised lens mount for focus, zoom and H/V shift.
A serial number is located on the side of the projector. Record it here:
Notes

page v
Digital Projection Mercury Quad Series
Rev A March 2017
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
CONTROL PANEL.......................................................................... 6
Buttons.................................................................................................. 6
Indicators............................................................................................... 7
REMOTE CONTROL....................................................................... 8
Infrared reception................................................................................ 11
POSITIONING THE SCREEN AND PROJECTOR........................... 12
Removing the detachable handles...................................................... 13
Roll and pitch ...................................................................................... 14
CHANGING THE LENS................................................................. 15
Inserting a new lens ............................................................................ 15
Removing the lens .............................................................................. 15
CHANGING THE LAMPS .............................................................. 16
CHANGING THE FILTERS............................................................ 17
Front lter............................................................................................ 17
Rear lter............................................................................................. 18
OPERATING THE PROJECTOR.................................................... 19
Switching the projector on................................................................... 19
Switching the projector off................................................................... 19
Selecting an input signal ..................................................................... 20
Selecting a test pattern ....................................................................... 20
Adjusting the lens................................................................................ 21
Adjusting the image............................................................................. 21
CONNECTION GUIDE ............................................................................23
SIGNAL INPUTS .......................................................................... 25
EDID on the HDMI and DisplayPort inputs ......................................... 26
Using HDMI/DisplayPort switchers with the projector......................... 26
3D connections ................................................................................... 27
3D sources up to 60Hz requiring frame doubling and left/right interleaving.......... 27
Frame sequential 3D sources up to 120Hz ................................................. 27
Dual Pipe 3D ...................................................................................... 27
3D Sync............................................................................................... 28
3D Sync in ......................................................................................... 28
3D Sync out ....................................................................................... 28
CONTROL CONNECTIONS........................................................... 29
LAN connection examples .................................................................. 30
RS232 connection example ................................................................ 31
OPERATING GUIDE ................................................................................33
USING THE MENUS ..................................................................... 35
Opening the OSD................................................................................ 35
Opening a menu.................................................................................. 35
Exiting menus and closing the OSD.................................................... 35
Inside a menu...................................................................................... 36
Accessing sub-menus........................................................................... 36
Executing commands............................................................................ 36
Editing projector settings..................................................................... 37
Using a slider to set a value.................................................................... 37
Editing numeric values .......................................................................... 37

page vi
Digital Projection Mercury Quad Series
Rev A March 2017
USING THE PROJECTOR............................................................. 38
Main menu .......................................................................................... 38
Lens menu .......................................................................................... 39
Lens Control....................................................................................... 39
Lens Memory...................................................................................... 40
Image menu ........................................................................................ 41
Noise Reduction .................................................................................. 42
Color menu.......................................................................................... 43
Color Space ....................................................................................... 43
Color Mode ........................................................................................ 44
Geometry menu .................................................................................. 49
Aspect Ratio....................................................................................... 49
Digital Zoom....................................................................................... 51
Overscan........................................................................................... 52
Blanking ............................................................................................ 53
Keystone ........................................................................................... 54
4 Corners .......................................................................................... 56
Rotation ............................................................................................ 57
Pincushion / Barrel............................................................................... 58
Arc................................................................................................... 59
Custom Warp ..................................................................................... 60
Edge Blend menu................................................................................ 61
Blend Width........................................................................................ 62
Black Level Uplift ................................................................................. 63
3D menu.............................................................................................. 64
3D types............................................................................................ 65
Some 3D settings explained ................................................................... 66
Frame rate multiplication in 3D images ...................................................... 67
Lamp Control menu............................................................................. 68
Setup menu......................................................................................... 69
ColorMax Setting ................................................................................. 71
Power On/Off...................................................................................... 72
Clock Adjust ....................................................................................... 73
OSD Settings...................................................................................... 74
Memory............................................................................................. 74
Network menu..................................................................................... 75
PIP menu ............................................................................................ 76
Information menu ................................................................................ 77
Signal Format ..................................................................................... 77
System Status .................................................................................... 78
Thermal Status.................................................................................... 78
Factory Reset ..................................................................................... 79
POSSIBLE COMBINATIONS OF SETTINGS.................................. 80
WEB CONFIGURATION UTILITY .................................................. 81
Projector Control page ........................................................................ 82
Network Setup page............................................................................ 83
Alert Email Setup page ....................................................................... 84
CONTENTS (continued)

page vii
Digital Projection Mercury Quad Series
Rev A March 2017
REFERENCE GUIDE................................................................................85
THE DMD™.................................................................................. 87
CHOOSING A LENS ..................................................................... 89
Basic calculation ................................................................................. 90
Basic calculation example................................................................... 91
Full lens calculation............................................................................. 92
Introducing TRC .................................................................................. 92
Calculating TRC .................................................................................. 93
Calculating the throw ratio with TRC ......................................................... 94
Full lens calculation example .............................................................. 95
SCREEN REQUIREMENTS........................................................... 96
Fitting the image to the DMD™........................................................... 96
WUXGA images displayed full width ......................................................... 96
WUXGA images displayed with a height of 1080 pixels.................................. 97
WUXGA images displayed full height ........................................................ 98
Diagonal screen sizes......................................................................... 99
Fitting the image to the screen.......................................................... 100
Positioning the screen and projector................................................. 101
POSITIONING THE IMAGE......................................................... 102
Maximum offset range....................................................................... 104
ASPECT RATIOS EXPLAINED.................................................... 105
Aspect ratio examples....................................................................... 106
FRAME RATES AND PULLDOWNS EXPLAINED......................... 108
Interlaced and progressive scan ....................................................... 108
Frame rates of image sources .......................................................... 108
Pulldowns - conversion into destination formats............................... 109
2:3 (normal) pulldown ......................................................................... 109
2:3:3:2 (advanced) pulldown................................................................. 110
APPENDIX A: LENS PART NUMBERS.........................................111
APPENDIX B: SUPPORTED SIGNAL INPUT MODES...................112
2D formats......................................................................................... 112
3D formats......................................................................................... 114
APPENDIX C: WIRING DETAILS .................................................116
Signal inputs and outputs.................................................................. 116
HDMI 1 and 2 ................................................................................... 116
DisplayPort ...................................................................................... 117
3G-SDI In, 3G-SDI Out........................................................................ 118
Control connections .......................................................................... 119
LAN ............................................................................................... 119
RS232 ............................................................................................ 119
Trigger 1 & Trigger 2 ........................................................................... 120
IR input ........................................................................................... 120
3D Sync IN and 3D Sync OUT .............................................................. 120
CONTENTS (continued)

Rev A March 2017
Mercury Quad Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4

Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev A March 2017
IN THIS GUIDE
What’s In The Box?............................................................................................. 3
Connecting The Power Supply........................................................................ 4
Projector Overview............................................................................................. 5
Front and rear views ...................................................................................................5
Control Panel........................................................................................................ 6
Buttons.........................................................................................................................6
Indicators.....................................................................................................................7
Remote Control.................................................................................................... 8
Infrared reception......................................................................................................11
Positioning The Screen And Projector....................................................... 12
Removing the detachable handles ..........................................................................13
Roll and pitch ............................................................................................................14
Changing The Lens........................................................................................... 15
Inserting a new lens..................................................................................................15
Removing the lens ....................................................................................................15
Changing The Lamps ....................................................................................... 16
Changing The Filters........................................................................................ 17
Front lter ..................................................................................................................17
Rear lter ...................................................................................................................18
Operating The Projector ................................................................................. 19
Switching the projector on.......................................................................................19
Switching the projector off.......................................................................................19
Selecting an input signal..........................................................................................20
Selecting a test pattern.............................................................................................20
Adjusting the lens.....................................................................................................21
Adjusting the image..................................................................................................21

page 3
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
Rev A March 2017
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
Only one remote will be supplied
with the projector. For more
information, see Remote Control
further in this guide.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
The lens support bracket needs to
be attached to the lens as shown
below:
If you need to install and use the
lens support bracket, remove the
gearbox outer cover (red arrow) in
advance.
Remote control
(117-780)
2x AAA batteries
User Manual on disc
(118-698)
Important Information
(117-786)
Power cable,
Europe
(118-728)
Power cable 125V,
North America
(118-726)
Projector
Power cable,
United Kingdom
(112-000)
HDMI cable
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Power cable,
China
(118-729)
remote control cable
1x M4 screw
Power cable 250V,
North America
(118-727)
1x lens support
bracket

page 4
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev A March 2017
Connecting The Power Supply
Lift the cable lock up, push the mains connector in rmly and push
the lock down to secure the cable.
1AC mains inlet with cable lock and power switch
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
1

page 5
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev A March 2017
Projector Overview
Front and rear views
1Front infrared window
2Power switch and power connection
3Connection panel
4Lens mount
5 Air inlet with replaceable lter
6Adjustable foot
7Detachable handle
8Air outlet
9Adjustable foot
10 Control panel
11 Lamp bay
12 Rear infrared window
13 Air inlet with replaceable lter
14 Detachable handle
15 Adjustable feet
Notes
Front view
4 5
3
1
7 8 910 6
2
Rear view 15
1211 13 14

page 6
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
CONTROL PANEL
Rev A March 2017
Control Panel
Buttons
1POWER button
Switch the projector on and off (in STANDBY mode)
2MENU button
Access the projector OSD (on-screen display).
3 Navigation (arrow buttons and ENTER)
Navigate the OSD and edit settings with the arrows, conrm choice with
ENTER.
4INPUT button
Select input source.
5Focus IN / OUT
Adjust focus.
6Zoom IN / OUT
Adjust zoom.
7Shutter CLOSE / OPEN
Open and close the shutter.
8EXIT button
Close the OSD.
9SHIFT button
Press and hold this button, then press the arrow buttons to move the
lens.
Notes
ERROR STANDBY
INPUT
CLOSE
FOCUS
ZOOM
SHUTTER
OPEN
OUT IN
OUT IN
SHIFT
MENU EXIT
1 2
3 4
Lamp
ENTER
2
3
4
6
1
7
5
9
8

page 7
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
CONTROL PANEL
Rev A March 2017
Indicators
1Lamp 1-4 indicators
Behavior Meaning
On (green) The lamp is switched on (100%).
On (amber) The lamp is running on less than full capacity
(77-99%).
Flashing (green) The lamp is warming up.
Flashing (amber) The lamp is cooling down.
On (red) Ballast Comms Error (call service)
Flashing (red) Lamp / Interlock Error
2 ERROR indicator (red)
Behavior Meaning
Flash once, then pause Lamp failure.
Flash twice, then pause Lamp door open.
Flash three times, then pause Fan failure.
Flash four times, then pause Over temperature.
On System error.
3 STANDBY indicator (green)
Behavior Meaning
On The projector is in STANDBY mode.
Flashing The projector is in STANDBY mode.
It can be switched on with a network command.
4 ON indicator (blue)
Behavior Meaning
Off The projector is switched off.
On The projector is switched ON.
Flashing The projector is warming up or cooling down.
Notes
1 2 3 4
ERROR STANDBY
INPUT
CLOSE
FOCUS
ZOOM
SHUTTER
OPEN
OUT IN
OUT IN
SHIFT
MENU EXIT
1 2
3 4
Lamp

page 8
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A March 2017
Remote Control
1Power ON / OFF
Turns power on and off.
2Pic Mute OPEN / CLOSE
Opens and closes the shutter.
2OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD
during projection.
4MENU
Press to access the OSD. Press again to hide the OSD.
5 Navigation (arrows and OK)
Navigate through the menus with the arrows, conrm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11
below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
7FREEZE
Freeze the current frame.
8DEFAULT
When editing a parameter, press this button to restore the default value.
9INFO
Access information about the projector.
10 RE-SYNC
Re-synchronise with the current input signal.
continues on next page...
Pic Mute
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
OPEN CLOSE
1
2
5
6
8
4
9
7
3
10
Notes

page 9
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A March 2017
11 LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12 USER PRESET A, B, C, D
Load user presets.
13 ALT
Press and hold this button to access alternative functions for all
buttons with a green label.
14 DVI / GAMMA / numeric input 3
Select the DVI input.
Use with ALT to switch to the next Gamma value:
...1.0, 1.8, 2.0, 2.2, 2.35, 2.5...
15 HDMI 2 / CON / numeric input 2
Select the HDMI 2 input.
Use with ALT to bring up the Contrast control, then adjust the value
with the LEFT and RIGHT arrow buttons.
16 HDMI 1 / BRI / numeric input 1
Select the HDMI 1 input.
Use with ALT to bring up the Brightness control, then adjust the
value with the LEFT and RIGHT arrow buttons.
17 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard,
CrossHatch, V Burst, H Burst, ColorBar...
When PIP mode is on, use this button with ALT to swap the main and
sub images.
continues on next page...
Notes
For further information about
user presets, see Memory in the
Operating Guide.
Remote control
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
13
11
12
14
15
16
17

page 10
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A March 2017
17 DISPLAYPORT / R / numeric input 4
Select DisplayPort input.
18 HD-T / G / numeric input 5
Select the HDBaseT input.
19 3GSDI / B / numeric input 6
Select the 3G-SDI input.
20 VGA / 3D / numeric input 7
Select the VGA input.
Use with ALT to toggle the 3D Format setting between Off and Auto.
21 COMP1 / EYE / numeric input 8
Select the Component 1 input.
Use with ALT to switch between left and right eye 3D dominance.
22 COMP2 / PIP / numeric input 9
Select the Component 2 input.
Use with ALT to switch on Picture In Picture (PIP) mode.
23 ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter
a two-digit address using the numeric input buttons. The indicator
will ash three times quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the
indicator ashes to conrm the change.
Notes
Remote control bottom
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
23
18
19
17
20
21
22
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Remote control top

page 11
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev A March 2017
Infrared reception
The projector has infrared sensors at the front and back.
The angle of acceptance is 40°. Make sure that the remote control is within the angle of
acceptance when trying to control the projector.
40°
40°
Infrared reception
Notes

page 12
Digital Projection Mercury Quad Series
Installation and Quick-Start Guide
POSITIONING THE SCREEN AND PROJECTOR
Rev A March 2017
Positioning The Screen And Projector
1. Install the screen, ensuring that it is in the best position for viewing by your audience.
2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to ll the screen. Set the adjustable feet so that
the projector is level, and perpendicular to the screen.
The drawing below shows the positions of the feet for table mounting, and the xing holes for ceiling mounting.
1Four adjustable feet
2Six M6 holes for ceiling mount
The screws should not penetrate more than 15 mm into the body of the projector.
Notes
Always allow the projector
to cool for 5 minutes before
disconnecting the power or
moving the projector.
Ensure that there is at least 50
cm (20 in) of space between the
ventilation outlets and any wall,
and 30 cm (12 in) on all other
sides.
Do not stack more than 3
projectors.
1
2
1
1
1
2
2
2
2
2