m-Dimension 1092 User manual

Give us a chance to make it right.
TOLL FREE: 1-866-528-8364
Do not return this item to the store. Contact our friendly customer
service department with any . Replacements
for missing or damaged parts are normally shipped the same day!
Monday - Friday, 8am-5pm, ET. After business hours, leave a message.
We will return your call the next business day.
problems or comments
Thank you for purchasing our fine product!
This package contains all tools necessary for assembly.
#1092 Wingback Arm Chair
Page 1
#1092 Wingback Arm Chair
Assembly Instructions
WARNING: Failure to follow these directions and warnings can result in serious injury
and/or product damage.
!Assistance is required to assemble this chair.
!Never stand on the chair or use it as a ladder.
!
!
!
!
!
Do not tip the chair when seated.
Periodically re-tighten all bolts and legs.
Do not exceed 250 lbs. (113.4 kg) weight limit on the chair.
If any parts become missing, damaged or worn, discontinue use until they are replaced with identical parts.
Always seek assistance before moving furniture.

Give us a chance to make it right.
TOLL FREE: 1-866-528-8364
Monday - Friday, 8am-5pm, ET.
Page 2
#1092 Wingback Arm Chair
Assembly Instructions
Step 1 - Remove all parts from their packaging and confirm that the quantities match those listed
above. If any parts are damaged or missing, please call our Customer Service Department at 1-866-
528-8364.
PARTS LIST
Part Drawing Part Name Qty.
A
Part Drawing Part Name Qty.
B
F
G
1 1
1 2
Seat Frame Wood Dowel
D
C
Right Arm
1
1 I
Allen
Wrench
1
Back Frame Seat Cushion
Left Arm
10
Bolt with
Washers
H
E
Legs
2

Give us a chance to make it right.
TOLL FREE: 1-866-528-8364
Monday - Friday, 8am-5pm, ET.
Page 3
#1092 Wingback Arm Chair
Assembly Instructions
Step 2 - Lay the Back Frame (Part A) on a flat surface. Pull the Velcro® attached dust cover on the
bottom of the Seat Frame (Part B) back to expose the inner frame. Align the bolt holes on the
underside of the Seat Frame with the corresponding bolt holes in the Back Frame like shown
below. Insert two Bolts with Washers (Part H) clockwise through the Seat Frame and into the
Back Frame. Tighten the bolts using the Allen Wrench (Part I). Do not over tigthen the bolts.
Step 3 - Lay the Right Arm (Part C) on a flat surface. Insert one Wood Dowel (Part G) through the
corresponding hole in the Arm located just below the top bolt hole. Attach the Leg (Part E) by
threading the Leg clockwise into the threaded insert located on the front corner of the Arm.
Tighten the leg until it is firmly seated and in line with the Arm frame.
-- Repeat Step 3 on the Left Arm (Part D).
B
A
GG
E
E
D
C
H
H
I

Give us a chance to make it right.
TOLL FREE: 1-866-528-8364
Monday - Friday, 8am-5pm, ET.
Page 4
#1092 Wingback Arm Chair
Assembly Instructions
Step 4 - Place the Back frame and Seat frame on their side as shown below. Align the wood dowel in the
Right Arm with the corresponding hole in the Back frame. With the arm seated against the chair
body, align the four bolt holes that connect the arm to the Back frame and Seat frame. Insert four
Bolts with Washers (Part H) through the chair body and into the Right Arm (Part C). Tighten the
bolts using the Allen Wrench (Part I). Do not over tigthen the bolts.
Step 5 - With help, place the chair body onto its back as shown below. Align the wood dowel in the Left
Arm with the corresponding hole on the Back frame. With the arm seated against the chair
body, align the two bolt holes that connect the arm to the Seat frame. Insert two Bolts with
Washers (Part H) through the Seat frame and into the Left Arm (Part D). Leave the bolts slightly
loose until instructed.
H
I
HH
H
C
D
H
I
H

Give us a chance to make it right.
TOLL FREE: 1-866-528-8364
Monday - Friday, 8am-5pm, ET.
Page 5
#1092 Wingback Arm Chair
Assembly Instructions
Step 6 - With help, carefully set the chair upright. Insert two Bolts with Washers (Part H) through the
Back frame and into the Left Arm. Tighten the bolts inserted in this step as well as the bolts
inserted in the previous step using the Allen Wrench (Part I). Do not overtighten the bolts.
Re- Attach the Velcro back flap and the bottom dust cover to the chair frame.
F
HI
H
Step 7 - Place the Seat Cushion (Part F) onto the Seat Frame .
Assembly is now complete.