DMP Electronics 736P Radionics Installation guide

INSTALLATION AND PROGRAMMING GUIDE
736P Radionics™ Popit
Interface Module

About the 736P........................................... 1
Feature ..................................................................... 1
Feature ..................................................................... 1
736P Features .............................................2
Install the 736P...........................................3
Mount the Module ............................................... 3
Wire the Module .................................................. 5
Connect to the Keypad Bus ............................ 5
Connect to the LX‑Bus...................................... 5
Connect Popex and Octopopit Modules.... 7
Convert Zonex Points to DMP Zones .......... 9
Test the Module..................................................25
Additional Information ........................... 26
Wiring Specifications.......................................26
Tamper Switch Connection ...........................26
Radionics Terminology.................................... 27
Compatible Radionics Devices .................... 27
TABLE OF CONTENTS
Product Specifications ............................28
Accessories................................................28
Compatibility ............................................28
Certifications............................................ 29
Underwriters Laboratory (UL Listed)........29

Digital Monitoring Products, Inc. | 736P Installation and Programming Guide 1
The Model 736P Radionics™ POPIT Interface Module allows a Radionics POPIT System to
interface to a DMP panel, while maintaining the existing Radionics wiring.
The 736P is supervised and connects to either the DMP Keypad Bus or LX‑Bus and
supports up to 32 Keypad Bus zones and up to 100 LX‑Bus zones.
All fire device installations must be in accordance with the manufacturer’s instructions,
NFPA standards, and the Authority Having Jurisdiction (AHJ) requirements.
ABOUT THE 736P

2 736P Installation and Programming Guide | Digital Monitoring Products, Inc.
736P FEATURES
Figure 1: 736P PCB and LEDs
DRXD
DTXD
ZRXD
ZTXD
LX
KEY
63
119
RED
BLK
DMP Bus Zone Expander
+AUX ZX DOUT COM
DMP Bus Receive Data
Transmit Data
Radionics Bus Receive Data
Transmit Data
Indicator LEDs

Digital Monitoring Products, Inc. | 736P Installation and Programming Guide 3
INSTALL THE 736P
Mount the Module
The736P comes in a high‑impact plastic housing that you can mount directly to a
wall, backboard, or other flat surface. For easy installation, the back of the housing
contains multiple holes that allow you to mount themodule on a single‑gang switch
box or ring. Themodule can also be mounted in a DMP enclosure using the standard
3‑hole mounting pattern. Refer to Figure 2and
Figure 3 as needed during installation.
1. Hold the plastic standos against the inside of the enclosure side wall.
2. Insert the included Phillips head screws from the outside of the enclosure into
the standos. Tighten the screws.
3. Carefully snap the module onto the standos.
1

4 736P Installation and Programming Guide | Digital Monitoring Products, Inc.
Figure 2: Mounting Hole Locations Figure 3: Stando Installation
Mounting
holes

Digital Monitoring Products, Inc. | 736P Installation and Programming Guide 5
Wire the Module
Use18to22gauge wire to connect the736P directly to the Keypad Bus or use a
dual‑ended4‑wire harness to connect directly to the LX‑Bus. This connection allows
the module to communicate with the panel and receive12VDC power. For more
information about wiring, refer to Wiring Specifications. Refer to Figure 4when
wiring the736P.
Connect to the Keypad Bus
1. Place a jumper across the bottom two LX/KEY pins.
2. Connect a4‑wire harness to the736P DMP BUS header.
3. At the panel, connect the wires to the corresponding Keypad Bus terminals.
Connect to the LX‑Bus
1. Place a jumper across the top two LX/KEY pins.
2. Connect one end of a4‑wire harness to the736P DMP BUS header.
3. At the panel, connect the other end of the4‑wire harness to the LX‑Bus.
2

6 736P Installation and Programming Guide | Digital Monitoring Products, Inc.
Red
To Keypad
Bus or LX-Bus
Black
Green
Yellow
+AUX to AUX
ZX to OUT
DOUT to IN
COM to COM
Radionics
POPEX or
OctoPOPIT
DMP Bus
Radionics Bus
AUX
OUT
IN
COM
Receive Data
Transmit Data
* All circuits are supervised Class B style 3.5.
* All circuits are power limited Class 2.
Indicator LEDs
Receive Data
Transmit Data
DRXD
DTXD
ZRXD
ZTXD
RED BLK
DMP Bus Zone Expander
+AUX
ZX
DOUT
COM
736P Radionics™ POPIT
Interface Module
LX
KEY
63
119
Figure 4: 736P Wiring