Dogtra 1100NC User manual

Copyright c 2001 Dogtra Company
REMOTE CONTROLLED
DOG TRAINING COLLARS
OWNER’S MANUAL
www.dogtra.com
2004
-

OVERVIEW
MAIN FEATURES
PRODUCT SAFETY AND HEALTH
STATEMENTS
COLLAR PACKAGE CONTENTS
DESCRIPTION OF TRANSMITTER PARTS
BUTTON FUNCTION
DESCRIPTION OF COLLAR PARTS
BATTERY CHARGER
CHARGING THE BATTERIES
TESTING YOUR
COLLAR
OPERATING INSTRUCTIONS
MAINTENANCE
ACCESSORIES
WARRANTY AND REPAIR
INFORMATION
2
4
5
6
7
12
13
19
20
23
25
28
29
30
1
CONTENTS

2
OVERVIEW
training collars give you the
ability to communicate with your dog in a
timely manner even when the dog is far away
from you. This makes it much easier for the
dog to learn its lessons because late corrections
are very confusing to the dog.
remote collars offer two
different kinds of stimulation:
Pressing the “Nick” button causes a very
short single pulse of electrical stimulation. It
automatically shuts off in a fraction of a
second, no matter how long the button is held
down.
The “Nick” is used as a substitute for leash
corrections when the dog is off lead.
It is mild but motivating!
OVERVIEW Pressing the “Constant” button causes the
collar to emit electrical stimulation that stays
on for up to twelve seconds as long as the
button is held down. “Constant” stimulation is
used for low level applications for guiding
dogs into the desired behavior or as a reserve
high to stop unsafe behaviors such as chasing
animals or cars.
All collars come complete with a
handheld transmitter, dog collar with receiver,
battery charger, test light and operating
instructions manual.
3
OVERVIEW

4
Easy to use transmitter.
All intensity level adjustments are made
from a digital dial on the transmitter. The
dial works like a rheostat, gradually
increasing the intensity with no jumps
between intensity levels.
Reliable stimulation effective for all types
of dogs no matter how heavy the coat.
The has a 1/2 mile range.
Waterproof collar receiver and water-
resistant transmitter on .
No external antenna on the collar receiver.
User replaceable and rechargeable Ni-MH
batteries.
Over 3000 different identity codes to
prevent conflicts with other collars.
MAIN FEATURES
MAIN FEATURES
5
PRODUCT SAFETY AND HEALTH STATEMENTS
collars use state-of-the-art micro-
technology.
If the constant button is held down for more
than 12 seconds, an automatic power-down
circuit will activate.
A filtering system prevents unwanted
reception from outside sources.
collars are intended for the sole use
for training dogs.
Dogs should be in good health during any
e-collar training.
collars are not intended for use on
dogs weighing less than 12 pounds or less
than 6 months of age.
Discontinue use if signs of irritation begins to
appear on the dog's skin around the neck
caused by the rubbing action of the collar
strap and/or contact points.
Do not attempt to test collars on
humans or other animals.
PRODUCT SAFETY AND HEALTH STATEMENTS

6
PACKAGE INCLUDES
Transmitter
Receiver
Battery charger and splitter cable
Test light
Owner’s manual
COLLAR
PACKAGE CONTENTS
7
TRANSMITTER
DESCRIPTION OF
TRANSMITTER PARTS
Antenna
Indicator Light
“Nick” Button
“Constant” Button
Intensity
Selection Dial
Battery Charging
Receptacle
and Cover
transmitter

8
TRANSMITTER
Transmitter Antenna
A short 2” antenna is supplied with the
.
The antenna should be screwed into the top
of the transmitter to ensure that the signals are
sent properly to the collar receiver and that
maximum range is attained.
2” Antenna
9
TRANSMITTER
Intensity Selection Dial
The intensity selection dial is located on the top of
the transmitter.
In the fully counter clockwise position- zero
setting- no electrical stimulation occurs even when the
transmitter button is pressed (a satety feature).
Moving the dial from the “zero” setting in a
clockwise manner, electrical stimulation will begin .
Moving the dial clockwise, the level increases in a
linear progression - no steps or increments up to the
level one hundred (fully clockwise).
Conversely, moving the dial counter-clockwise, the
level reduces in a downward linear progression until at
the “zero” setting (fully counter-clockwise).
This feature allows for subtle adjustment of the level
(upward of downward) while the transmitter button is
held down continuously - providing e-linear training.

10
TRANSMITTER
Transmitter Battery Charging Receptacle
Located on the side of the transmitter, the
receptacle is covered by a rubber plug. Insert
one end of the battery charging cable into the
receptacle to charge the battery.
(See Battery Charging Procedure.)
After charging is completed, close the
receptacle with its rubber plug to prevent dirt
from getting inside.
Transmitter
Charging
Receptacle
11
TRANSMITTER
Transmitter Indicator Light (LED)
The transmitter indicator light is located by
the intensity selection dial.
When a button on the transmitter is pushed,
the red light comes on to indicate that the
transmitter is being activated.
If the indicator light emits a double blink
while the button is pressed, the battery needs to
be recharged.
LED

12
BUTTON FUNCTION
The transmitter for has two
buttons.
The top button gives “Nick” stimulation when
pressed. The bottom button gives “Constant”
stimulation for as long as you press the button up
to twelve seconds.
BUTTON FUNCTION
Constant
Nick
13
BUTTON FUNCTION
“Nick” Button
When the “Nick” button is pushed, the
receiver emits an extremely short pulse of
electrical stimulation that automatically shuts off
no matter how long you leave your finger on the
button. The “Nick” is mild but motivating!
“Constant” Button
Pressing the “Constant” button gives
stimulation for up to twelve seconds, at which
time, the collar will turn off. The collar will
reactivate, when you push the button again.

14
COLLAR
DESCRIPTION OF
COLLAR PARTS
Collar
On/Off Button
Contact Points
Indicator
Light
Battery
Charging
Receptacle
and Cover
Collar strap
15
COLLAR
On/Off Button
To turn the collar on, press the button on
the end of the receiver for one full second until
the light comes on.
To turn the collar off, hold the button down
for one full second until the red light goes off.
A delay has been built into the on/off switch
so the dog cannot turn the collar off by accident.

16
COLLAR
Receiver Indicator Light (LED)
Located on the front of the collar, the indicator
light comes on and blinks once every 2 seconds
after the collar is turned on.
The blinking will change from a single flash to a
double flash, when the collar needs to be recharged.
When the “Constant” button on the transmitter is
pushed, the collar indicator light will glow steadily
for as long as you hold the button down, for up to
twelve seconds. When the “Nick” button is pushed,
the light comes on for a fraction of a second.
17
COLLAR
Contact Points
The collar should be fitted so that the
stainless steel contact points press firmly against
the dog’s skin.
A loose fit can allow the collar to move
around on the dog’s neck. When this happens,
the contact points may rub the skin and cause
irritation. If the collar is too loose, electrical
contact will be inconsistent and your corrections
will be inconsistant also.

18
COLLAR
Receiver Battery Charging Receptacle
On the inside of the collar, next to the collar
strap, is a battery charging receptacle with a
rubber cover plug.
Internal Antenna
The has no external antenna
on the collar. The Antenna is inside the collar
receiver.
Receiver
Charging
Receptacle
19
BATTERY CHARGER
The battery charger and charging cables
allow you to charge both the transmitter and
receiver at the same time.
The battery charger is designed for a 110
volt wall outlet. (European 220 volt AC
chargers and 12-volt field charger for your
automobile are also available).
BATTERY CHARGER
Charging Cable
110 volt
Charger

20
CHARGING THE BATTERIES
uses Ni-MH (Nickel-Metal-
Hydride) batteries that do not set a memory and
can be charged on a regular basis without harm
to the battery. There is no need to completely
drain the batteries between charges.
1. Charge the batteries for 14 hours before using
the collar for the first time.
2. Do not charge the batteries near any
flammable substances.
CHARGING THE BATTERIES
21
CHARGING THE BATTERIES
3. Fully charge the batteries for 14 hours if the
collar is to be stored without use for a period
of a month or more.
4. Recharge the battery if
- the indicator light on the collar is emitting a
double blink every 2 seconds,
- the indicator light on the transmitter or
receiver does not come on,
- the indicator light on the transmitter or
receiver comes on momentarily but does not
stay on, when the “Constant” button is
pushed.

22
CHARGING THE BATTERIES
Battery Charging Procedure
1. Attach the charging cables to both the
transmitter and receiver(s), as shown on page 21.
2. Plug the charger into a 110-volt wall outlet as
if using the accessory field charger plug into a
cigarette lighter.
(Use 220-volt European charger for Europe)
When properly plugged in, all indicator lights
should glow red.
The receiver automatically turns off, when you
insert the charging cable into the battery
charging receptacle on the receiver.
3. After charging, cover the battery charging
receptacles with the rubber plugs on the
transmitter and receiver.
4. Battery is fully charged with a 14-hour charge.
23
TESTING
1. Turn the power switch on by pressing the
button on the end of the collar receiver for one
second. The indicator light will come on for a
moment then blink once every two seconds,
showing that the collar is ready to use. (If the
red indicator light emits a double blink every
two seconds, the batteries need to be charged.)
TESTING YOUR
COLLAR

24
TESTING
2. Place the test light on the receiver contact
points and hold it there.
3. Set the transmitter intensity dial to level
one hundred and push the “Constant” button.
4. Watch the test light as you push the
“Constant” button on the transmitter.
It should glow brightly. As a safety feature the
collar will automatically turn off after twelve
seconds. To reactivate, release the button for
one second and the collar will reset.
5. Push the “Nick” button. The test light should
light for just a moment.
6. Change the intensity dial to level fifty and
repeat the test. The test light should glow
dimmer.
NOTE : It is normal for the test light not to come
on if the intensity level is set below level
zero.
25
OPERATING
Fitting the collar
The collar strap should be adjusted so that
the contact points are held firmly against the
dog’s skin. If the collar is too loose, it can cause
irritation from the contacts rubbing against the
skin.
If the dog has a heavy coat, move the
receiver up and down to work the contact points
down into the coat.
ATTENTION!
Avoid having the dog wear the collar with
the contact points in the same place for more
than two hours at a time. Leaving the points
on the same spot for extended periods of time
can cause skin irritation. If the dog is to wear
the e-collar for long periods, occasionally
reposition the collar so that the contact points
are moved to a different spot on the dog’s
neck.
OPERATING INSTRUCTIONS

26
OPERATING
Intensity selection
To select the intensity level, start on “zero”
setting. Gradually increase the level until you get
a response from the dog that would be equivalent
to a quick pull or “POP” with a leash.
Remember that you will need to adjust the
setting (upward or downward) as the dog’s
attitude changes, especially during times or
increased excitement or distraction.
27
OPERATING
Maintenance
Always clean and rinse the collar thoroughly
with tap water after use in salt water.
The receiver and collar strap should be
periodically cleaned with detergent and water to
prevent malfunction. Remove the contact points
and clean the area beneath the strap.

28
MAINTENANCE
Reception
The collar has a range of a
half-mile. Depending on the way you use your
transmitter, the transmitting range might be quite
different.
You will have more range if you hold the
transmitter away from your body, when you push
the button.
Maximum Range
Typical Range
Minimum Range
If your finger touches the antenna near the
dial on the top of the transmitter, the actual
range may be reduced, while you push the
button on the transmitter
29
ACCESSORIES
The following items may be purchased
separately
European Charger
Designed for use with 220V AC electrical
outlets in Europe.
Field Auto Charger
Designed for use with the 12-volt cigarette
lighter in your car.
ACCESSORIES

30
WARRANTY
Warranty Repair
provides the original
purchaser a two-year limited warranty for repair for
the 1100NC on parts and labor from the date of the
original purchase. Batteries or the labor to replace
them are not covered under warranty after the first
year. (The two-year warranty applies only to
purchases made after January 1, 2003. All products
purchased before 2003 carry a one-year warranty.)
DOES NOT replace defective units or
refund after 30 days of purchase.
Dogtra’s warranty DOES NOT cover repairs or
replacement due to misuse, improper maintenance
or lost units. All replacement cost for either the
transmitter or receiver is the owner’s responsibility.
The warranty is void if the unit has been altered
or an unauthorized person has attempted repair
work.
WARRANTY AND
REPAIR INFORMATION
31
WARRANTY
Return shipping of warranty work is the owner’s
responsibility. The cost for shipping (via regular
ground service) back to the customer is covered by
Dogtra Co. within the continental United States.
Any expedited shipping service will be at the
owner’s expense.
A copy of the sales receipt showing purchase
date is required before warranty work is begun.
Write a note briefly explaining the problem and
include your name, address, city/state/zip code,
daytime phone number and evening phone number.
Send unit for repair to :
22912 Lockness Avenue
Torrance, CA 90501
For any questions concerning your dogtra
products call us Toll Free at 1-888-811-9111.

32
Send repair units to :
Dogtra Company / Repairs
22912 Lockness Avenue
Torrance, CA 90501
U.S.A.
REPAIR
Out of Warranty Repair
For repair work that is no longer covered by
warranty, the cost of repair will include parts, labor and
shipping. Write a note briefly explaining the problem.
Include your name, address, city/state/zip code,
daytime phone number and evening phone number.