DREAMS Alana Lifestyle Bed User manual

Two person
assembly
1 hour approx
assembly time
MK1 221112
Alana Lifestyle Bed
SLEEPMOTION

Alana Sleepmotion Lifestyle Bed - Assembly guide - Page 2
Thank you
Hello, thanks for choosing to purchase your bed from Dreams - you're now on your way to your best
ever night's sleep. Before you begin building your bed, please take a moment to read through the
instructions and make sure that you've got all the relevant parts listed on the following pages.
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your bed.
We advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
Help and support
At Dreams, it’s our mission to give the whole nation a great night’s sleep - this
means that the quality of our products is of utmost importance to us. If there
are any issues with your product or any missing parts, please contact our Help
Centre on 0800 652 6750, where a member of our team will be happy to help.
(For customers based in Northern Ireland, please call 028 9050 8300)
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this bed which could
present a choking hazard. All plastic and wrapping materials should also be
To keep your little ones busy, there is a colouring page inside the back cover.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.
We recommend that you build your new bed in the room you’d like it to be
located - this will help prevent any risk of damage to your newly built bed
whilst moving it.
Top tip

Alana Sleepmotion Lifestyle Bed - Assembly guide - Page 3
1
1
2
2
2
2
4
A. Headboard
B. Footboard
C. Side rails
D. Plain legs for headboard
E. Castor legs for footboard
F. Locking washers
G. Floor protector cups
A
B
C
C
Parts list
Parts
The bed you have purchased comes with a Sleepmotion 200I electric bed base.
Once the base is built, place it in the location where it shall be used then please follow the steps in this
Assembly Instruction to build your bed-frame around the base disregarding the assembly guide packed
inside Pack 3.
Tools required
Please check you have these tools below
Tape
measure
817161514131211101019876543210cm
Fittings
Please check you have all the parts listed below with your product:
a x12 b x12 c x12
Bolts (M8x30mm) for fitting
side rails (C) to headboard
& footboard (A&B) Flat washer for M8 bolts
Spring washer for M8 bolts
Hardware needed for fixing side rails to headboard & footboard
Packed in side rail pack 3L- hardware pack (A).
d x1
Allen Key for M8 bolts
DE
FG

Alana Sleepmotion Lifestyle Bed - Assembly guide - Page 4
Before starting assembly please refer to the owners
manual supplied with your Sleepmotion 200i bed
base and follow the instructions taking note of any
safety precautions or operational safety requirements
of the installation.
In the room where bed will be used, first prepare the bed base by fitting the eight long
legs - 6‘’ (15cm), see Step 1 (iv).
Connect the power and check the operation then step by step follow the bed assembly
instructions below, to build the bedstead around the Sleepmotion 200i bed base.
Important:
B
a
c
b
B
A&
a
x8
b
x8
c
x8
1
A
D x2
F x2
F x2
Prepare the bed for assembly.
Prepare the headboard & footboard or assembly by loosely inserting the screw sets (a, b & c).
Slide the locking washers (F) over
the threaded studs on the plain legs
(D) and screw them into headboard.
Please do not overtighten.
ii)
i)
E x2
Slide the locking washers (F) over the threaded
studs on the castor legs (E) and screw them into
footboard. Please do not overtighten.
iii)

Alana Sleepmotion Lifestyle Bed - Assembly guide - Page 5
2
ax1 bx1 cx1 dx1
10mm
20mm
A
a
cb
d
C
90%
iv)Into the underside of the bed base, screw in the eight 6" (15cm) legs as shown.
Position the electric bed base.
With the headboard in the final location in which it shall be used, attach the right hand side rail to it.
Make sure the electric bed base is the correct way round with mattress stopper at the footend.
Carefully lift and place the electric bed base into the corner between headboard and side rail as
shown - it is heavy so please get help.
Leave an even gap around the perimeter, see sketch below right.

Alana Sleepmotion Lifestyle Bed - Assembly guide - Page 6
3
cx1
dx1
ax1
bx1
4
A
ac
b
d
C
90%
i) Route the power lead under the headboard and plug into the wall socket - for
safety this must be an earthed power supply.
ii) Raise the head and foot ends of the bed base using
the remote control.
Connect the power to the electric bed base.
Connect the left hand side rail to the headboard.

Alana Sleepmotion Lifestyle Bed - Assembly guide - Page 7
5
6
10mm
30mm
10mm
20mm
Flatten the bed and check the gaps are as per the sketch below
100%
ax2 bx2 cx2 dx1
Make sure everything is working properly then fit the footboard
Make certain the bed is squared up as shown in the
diagram then tighten all bed assembly bolts 100%.
B
a
cb
d
C
90%
G x2
If required, put the floor
protector cups (G)
under the castors.

Care and maintenance
Here are some tips to keep your new bed in tip-top condition
Alana Sleepmotion Lifestyle Bed - Care and maintenance guide - Page 8
Cleaning
To clean your new bed, we'd advise using a warm damp cloth or if fabric, remove
dust using a low suction vacuum cleaner.
Please do not use abrasive chemicals or bleach as this may damage the product.
Checking and moving
Periodically we recommend you check that the screws or fixtures haven't become
loose over time. To move your new bed, we recommend lifting it where possible, as
dragging or pushing it could cause damage to the legs or flooring.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Fabric
Please note depending on the lighting, positioning and surroundings of your
period of time, the colour might lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. We recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Thank you for shopping with us - we hope you have a
great night's sleep.
Technical Specifications
Overall Dimensions (LWH mm)
Double:
King: 2410 x 1635 x 1355
2310 x 1485 x 1355
Super King: 2410 x 1935 x 1355
Double:
King: 2050 x 1530
1950x 1380
Super King: 2050 x 1830
Internal Dimensions (LW mm)
170
170
W
H
L
350
Floor to top
of base
30
Top of base to
top of side rail
40
750
130

Little dreamers
Keep the little ones entertained while
you assemble your new purchase.