DREAMS San Diego TV Bedstead User manual

*Only supplied if upgraded sprung system chosen
5
6
14
San Diego TV Bedstead
Parts Identification
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a
safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
a way from young children whilst assembling your unit to
avoid the danger of choking hazards.
Qty
1
2
3
4
5
6
Headboard
Footboard
Right Side Rail
Left Side Rail
1
1
1
1
Wooden Slats
Metal Sprung Slat System*
1 Set
1 Frame
Parts Checklist
Ref.Description
Note:
Standard wooden slat frame (part 5)
Upgraded sprung slat frame (part 6)
1
2
3
4
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THE HELP GUIDE PAGE
Page 1 of 6

DOWN
UP
QtyCode Description
In the unlikely event of missing or damaged parts, please
contact the customer service team on 08442 920000.
When calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
This assembly requires two
people.
Ax8
Bolt (M8x30mm)
Fittings Checklist
Cx8
Spring Washer
Dx8
Flat Washer (8mm)
Additional Tools Required
Gx1
Allen Key (4mm)
Fx6
Sleeve Nut (M6x16mm)
QtyCode Description
BBolt (M6x40mm) x6
General Hints & Tips
Care & Maintenance
Crosshead Screwdriver
Hx6
Flat Washer (6mm)
IScrew (3x20mm) x2
EAllen Key (5mm) x1
OBolt (M6x15mm) x8
Note: The following fillings will be found in the box which contains the sprung slat frame, not with the bed frame
assembly hardware pack.
P
Qx2
x1
x1
TV Lift Switch
J
Please retain your Assembly Instruction and
tools provided, for future use. Periodically
check that all bolts are still tight.
Page 2 of 6
(Battery - A23-12Volt)
Slat Centre Leg
Slat Support Leg

Cx8 Dx8 x2
I
Ax8 Jx1
UP
DOW N
Bed Assembly
Stage
1
1
J
I
Fit the bolts (A), spring washers (C), and flat washers (D) to the holes in the headboard (1) and footboard
(2) as shown. Note: Do not fully locate the bolts, but leave 10mm protruding.
Fit the side rail (3 & 4) to the headboard and footboard locating the brackets behind the flat washers.
Once all four corners are located, fully tighten the bolts using the allen key (E).
1
3
A
C
D
10mm
1
2
3
4
Page 3 of 6
DOWN
UP
UP
DOWN

Use all of the x6 bolt sets provided (B, H & F).
Use x4 of the x6 bolt sets provided (B, H & F).
6
Bed Assembly
Stage
2a UPGRADE SPRUNG SLAT SYSTEM
6
6
Hx4
Fx4
Bx4
Ox8
6
Q
P
Q
Stage
2BED SLAT FIXING Hx6
Fx6
Bx6
5
5
5Lay the set of slats (5) onto the slat
support rails on the side rails.
Align the first and last slat with the
end of the rails, and secure in place
using the bolts (B), washers (H) and
sleeve nuts (F). Fully tighten using
the allen key (G).
Once secure fix the centre slat using
the bolts as before.
Open the metal frame and lay face down on the working
surface.
Fit the support legs (P & Q) to the positions shown, securing
with the bolts (O). Fully tighten using the allen key (G).
Carefully turn the slat frame over, and position onto the slat
support rails. Align the frame with the fixing holes at each
end and secure using the bolts (B), washers (H) and sleeve
nuts (F). Fully tighten using the allen key (G).
Finally, please ensure that all bolts are fully tightened
before the bed is used.
EITHER 5 OR 6 WILL BE SUPPLIED - BOXED SEPARATELY
Page 4 of 6

If you have any problems, refer to troubleshooting guide on the next page..
We hope you will be very happy with your TV Bedstead but please read these points carefully; they will help
you assemble the bed and media successfully:
IMPORTANT: BEFORE FITTING THE MATTRESS… Please do the following
1) In the compartment of the footboard (with red label), open the lid and carefully remove the long accessory
box and ALL transit material. Please dispose of this material in a safe environmentally friendly fashion.
2) The box contains the following:
a. HARDWARE KIT TO ASSEMBLE THE BED
b. MAINS POWER LEAD – 3 MT LONG
c. AERIAL LEAD – 3 MT LONG
d. TV REMOTE CONTROL
e. TV OPERATION GUIDE
f . TV LIFT REMOTE SWITCH
3) If you want to keep the accessory box, do NOT return it to the transit position as it could damage working
parts.
4) Keep children & other adults well clear of the foot end of the bed, when operating the TV Lift Switch.
5) In the centre of the footboard, under the bed, is a compartment containing a connection box for mains
power input plug which is on the end of the 3Mt lead, aerial connection and x2 HDMI connections.
a. Plug the power and aerial cables into the sockets and other end into the wall sockets.
b. Plug your media into one or both of the HDMI sockets as appropriate.
6) Check that power is available and test the TV Lift – just press UP button.
7) Check TV works and is switched ON – switch is underneath TV, on right hand side.
8) Switch on TV and refer to TV Operation Guide to set up TV.
9) To lower TV, press DOWN button on TV Lift Switch – power to the TV will shut off when the TV reaches the
bottom of the stroke - lid will close automatically..
10) To raise TV, press UP switch and TV will rise to the TOP and power will be restored then TV Lift will stop
automatically at the top of it's travel.
Now it is time to fit the mattress…
IMPORTANT: SOMETIMES YOU NEED TO PRESS THE SWITCH TWICE IF YOU GO UP/DOWN or DOWN/UP
QUICKLY, THIS IS NORMAL AND IS NOTHING TO BE CONCERNED ABOUT. IN NORMAL OPERATION
WHEN LIFT IS UP or DOWN FOR MORE THAN 5 MINS, PRESSING ONCE IS SUFFICIENT.
Help Guide
Page 5 of 6

Check Power
Open the lid; one can easily see the controller on left hand side of the TV Lift.
When power is feeding through to the TV Lift - the light (1) is glowing.
If it is NOT glowing - power is not reaching the system. Check mains power is
switched on and the plug is pushed firmly into the power socket on bottom of
footboard.
1) If TV fails to work , check power connections and that TV is UP as power will be off when it is down. Check
TV Guide for trouble-shooting help if necessary.
2) If your TV Lift does not operate, please check all power connections at the wall socket and into the base
of the footboard.
3) If your TV Lift still does not operate - change the battery in the remote switch on the side-rail of the bed -
refer to TV Lift Guide help-page to show how to change battery.
4) If you are sure there is a real problem, please contact customer service on 08442 920000.
TROUBLE - SHOOTING
TV LIFT GUIDE
IF FOR ANY REASON THE TV LIFT DOES NOT WORK, PLEASE CHECK THE FOLLOWING.
Check Battery in the Switch
Battery Replacement
Battery Specification: A23 - 12Volt
Tool Requirement: Crosshead screwdriver.
Remove switch from side-rail of bed - follow the Steps:
Step 1: Take off the front buttons of the switch.
(Push the lock bars at back if switch inwards to
release front buttons).
Re-assemble switch.
Test the switch - then re-place in the side-rail correct
way up-front of switch is marked.
Help Guide
Page 6 of 6
UP
DOWN
DOWN
UP
UP
DOWN
(1)
1
2
Step 2: Change the battery making sure you fit it the correct
way as shown....