DREAMS ISABELLA BED User manual

1 of 5
ISABELLA BED
Assembly Instructions
NOTE: It will require two people to assemble this bed.Assembly should be carried out in the room that
the bed will be used in.
1. We suggest you spend a short time reading through this leaflet and then
follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the
assembly should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children’s reach.
In the unlikely event that this product has missing or damaged parts, please
call 03442 920000 to obtain spares
spare
Before you
start, here
is some
helpful advice
Minimum No. of people

recommended to assemble
This product.
Approx assembly time:

1
hour

2 of 5
Component parts and fittings contained in the box
PARTS
Fittings
A
B
C
D
E
F
G
H
I
J
K
L
N
M
Locking Nut 16pcs
M8 Barrel Nut 4pcs
M8 x80mm Bolt 4pcs
Φ8 Washer 4pcs
Locking Pin 16pcs
Φ10Dowel 4pcs
Φ8 Dowel 12pcs
1/4″JCN Nut 4pcs
1/4″*3/4″Bolt 4pcs
M8*20 Bolt 10pcs
Nut 2pcs
Spanner 1pc
4MMAllen key 2pc
5MMAllen key 1pc
1 piece
1 piece
2 pieces
1piece
2 pieces
1 piece
2 pieces
2 pieces
2 pieces

3 of 5
ASSEMBLY
1) Fit wood dowels (G) into holes in the
ends of side rails (4) and center rail (5).
Screw Locking Pins (E) into the
headboard panel (3).
2) Use Locking Nuts (D) to fix the
headboard onto side panel (4) and
center panel (5).
1) Assemble footboard panels (2&3) to the
side rails (4R&4L). Secure by tightening the
locking nuts in the same way as described in
step 1.
STEP 1
STEP 2

4 of 5
ASSEMBLY
1) Fit the headboard (1) to the unit.
1) Fit the mattress support rails (9) to the
slat frame (8).
1) Screw the Nut (N) onto the piston
bracket .
STEP 3
STEP 4
STEP 5

5 of 5
ASSEMBLY
1) Two people carefully lower the slat frame
onto the piston bracket . Secure by
threading bolts (J) to slat frame on the
piston bracket .
.
1) Position base boards (6&7) into the bed
frame.
STEP 6
STEP 7

Carton Information
Carton Dimensions (CM)
H L W
Weight
Kg
H L W
Weight
Kg
H L W
Weight
Kg
H L W
Weight
Kg
H L W
Weight
Kg
H L W
Weight
Kg
Single
4ft
Double 9152 120 18 6.5 194 27.8 13 14.3 204 32.7 27 9.5 194 40.3 23 13 139 101 17
King 9167 120 20 6.5 204 27.8 15 14.3 214 32.7 29 9.5 204 44 25 13.5 154 106 20
Super King
Size
Single
4ft
Double
King
Super King
Head End
Side Rails
Footend
Drawers
Feet
Centre Support Leg
Ottoman base composition
Middle Rail
part 2&4
part 6&7
part 8&9,A.I,hardware
Carton Content - Parts as per Assembly Instructions
part 1
part 1
MDF with ash veneer
Product Composition
Size
part 3&5
part 2&4
Box 3
Box 4
Box 5
part 3&5
part 6&7
part 8&9,A.I,hardware
Particle board with ash veneer, etc…
Box 6
Box 1
Box 2
Box 3
Box 4
Box 5
Box 6
Box 1
Box 2
Plyboard, Solid ash, etc….
Solid ash, Particle board with ash veneer, etc…
Solid ash, Particle board with ash veneer, etc…