DV8 OFFROAD DMT3-01 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
4 RUNNER DASH MOUNT
2010+ (5TH GEN) TOYOTA 4RUNNER
DMT3-01
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
-Drill
-3mm, 4mm Allen Bit
-10mm Wrench
-10mm Socket
-Trim Clip Tool
-11/32” Drill Bit
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
- 1 Hour
Time to install this should only
take about an hour
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Remove the side trim pieces
by pulling towards the rear of the vehicle.
These can be a little difcult to remove.
Use a trim clip to apply pressure to the
clips behind the trim, while pulling on it,
if necessary.
STEP 2 | Remove the control cluster
by pulling towards the rear of the vehicle
to release the clips, and disconnect the
wiring connector on the back.
Begin by unpacking all items and
inspecting for missing pieces or damage. If
you have any concerns, please contact the
company the product was purchased from.
(2) M6x15 Allen
(2) M6x30 Allen
(4) M6 Flat Washers
(4) M6 Nylon Lock Nuts
(2) M5x10
(2) M5 Flat Washers
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 3 | Slide the two M6x30 bolts
through the dash mount and place it in
the desired install location.
When it is adjusted as desired, use a
4mm allen bit to spin the bolts so they
make marks on the dash for drilling.
Use a sharpie to mark the side mounting
holes for drilling.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 4 | Remove the dash piece to
prepare for drilling by removing the four
bolts securing it using a 10mm socket.
STEP 5 | Drill out the marked holes
using an 11/32” drill bit.
STEP 6 | Install the dash mount onto
the dash piece using the provided M6
hardware with a 4mm allen bit and 10mm
wrench.
The longer M6x30 hardware will be used
for the top mounts and the shorter M6x15
hardware will be used to secure the sides.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 7 | Re-install the top dash
piece using a 10mm socket and factory
hardware.
STEP 8 | Install the control cluster
and dash trim by applying pressure until
the clips are secured.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 9 | If desired, install the arms
onto the dash mount using the provided
M5 hardware and a 3mm allen bit.
STEP 10 | Congrats! You are nished
with the install of the 2010+ (5th Gen)
Toyota 4Runner Dash Mount!