DV8 OFFROAD SPBR-01 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
855-680-9595
NEED HELP?
PRODUCT
INSTALLATION MANUAL
Front Skid Plate
2021 FORD BRONCO
SPBR-01
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- 13mm & 15mm socket
- T40 torx bit
- Grinder/sawzall
- Push pin puller
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 person
Novice/intermediate skill level
required. Minor wiring needed.
- Approximately 1 hour
Time to install this should
take about an hour.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

INSTALLATION MANUAL
855-680-9595
NEED HELP?
STEP 1
REMOVAL OF FACTORY STEEL BUMPER
STEP 2
Begin by removing the front plastic
d-ring guards. Using a screwdriver or
push pin remover, remove the (2) pins
on the bottom and (2) near the top of
the d-ring mount.
Using a 15mm socket, loosen the (3)
bolts on each side.
Note: When you do this, the bumper can
become free from the vehicle and can fall.
Ensure you have another person holding
it, or the bumper secure to prevent falling
and injury.
Pull the top half away from the Bronco
and set to the side. Repeat for the
other side.

INSTALLATION MANUAL
855-680-9595
NEED HELP?
STEP 3
Once all bolts are loose, remove the
plug for the fog lights and front sensors
if equipped. This is located at the back
end of the grill on the driver side.
STEP 4
Once unplugged, remove all (6)
bumper bolts and d-rings mounts.
Set bumper face down off to the side.

INSTALLATION MANUAL
855-680-9595
NEED HELP?
STEP 5
STEP 7
Remove the rubber/plastic shroud
under the grill by pulling the tabs
on the shroud away (up/down) from
vehicle while pulling the shroud from
the vehicle.
Reach behind each bumper mount on
the frame rail and remove the factory
nut plate.
STEP 6
If you do not have adaptive cruise
control, remove the plastic cover by
pushing the clip on the top down
while pulling away from Bronco, and
set off to the side.
Note: If you have adaptive cruise control,
you will need to relocate the module using
our ABBR-01 to retain the functionality
(Adaptive Cruise Control Relocation
Bracket).

INSTALLATION MANUAL
855-680-9595
NEED HELP?
STEP 1
STEP 2
Using a 15mm socket, remove the four
bolts holding the skid plate to the
vehicle.
Note: There will be six bolts if your Bronco
was equipped with the factory plastic
skid plate.
INSTALLATION OF DV8 SKID PLATE
Begin by unpacking all items and
inspecting for missing pieces or
damage. If you have any concerns,
please contact the company the
product was purchased from.
(6) M12x500 Bolts
(6) M12 Nuts
(6) M12 Split Washers
(12) M12 Flat Washers
Hardware Included:

INSTALLATION MANUAL
855-680-9595
NEED HELP?
STEP 3
STEP 4
Remove the skid plate from the
Bronco. Keep factory hardware since
this will be reused for install.
If you have the factory plastic bumper,
you will need to trim the D-Rings
ush with the skid plate bracket as
shown using a Sawzall/grinder.

INSTALLATION MANUAL
855-680-9595
NEED HELP?
STEP 5
Hold up your new DV8 skid plate
and position mounts around each
frame horn. Using a 15mm socket and
factory hardware, loosely mount the
skid plate to the Bronco.
STEP 6
With the skid plate loosely installed,
you can now install your bumper
of choice. Tighten the bolts on the
bottom of the skid plate to 55 ft. lbs.
You are now done with the install of your
new DV8 Front Skid Plate.