DV8 OFFROAD TCTT2-01 User manual

NEED HELP? 855-680-9595
PRODUCT
INSTALLATION MANUAL
6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and knowledge
of basic mechanical work. If you do not feel that you are
capable of performing this install please take this product
to a trained professional.
After reading this guide please contact us with any questions
or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm
to you or your vehicle as a result of an improper install.
Proper installation of this kit requires knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop
manual and any special tools needed to service your vehicle be on
hand during the installation. Installation of this kit without proper
knowledge of the factory recommended procedures may affect the
performance of these components and the safety of the vehicle.
• Always wear eye protection when operating power tools. •
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing
from kit, please be prepared to provide the following information:
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
TCTT2-01
2007-2020 TOYOTA TUNDRA
UNIVERSAL TIRE MOUNT
TOOLS REQUIRED
– T55 head socket
– 13, 16, and 19mm sockets
– 19mm box wrench
– Appropriate ratchet for sockets
– Safety Glasses
TIME REQUIRED
– 30-45 min.
Time to install this rack
should only take 30 to
45 minutes with help.
SKILL LEVEL
- Novice/Intermediate
– 1 to 2 persons, you and a buddy
Slight skill level required, you
and a buddy can easily install it
with little effort

NEED HELP? 855-680-9595
INSTALLATION MANUAL
STEP 1:In the box you will find...bottom rail
bed mount, brackets, main tire
vertical mount, bed/vertical brace,
tire mounting hardware, and all
mounting nuts and bolts.
STEP 2:Using the T55 head socket take out
the 2 bed bolts shown here.
STEP 3:Next bolt on the 2 bracket mounts to the
bottom main rail using the 16mm bolts
and nuts. Finger tight only as you will
need to adjust the mounts as you install.
The brackets mount on opposite sides of
the rail as shown in photos.
STEP 4:Next re-install the bed bolts and loosely
tighten.
STEP 5:Next align the main bottom rail with the
bed of the truck. This ensures the carrier
will be straight within the truck bed.
When aligned...tighten the bed bolts.
Note: This universal in-bed tire mount
can be mounted on either side
of the bed. We are mounting it
on the passenger side. For driv-
ers side...just flip the bottom
main rail over so the flat side
faces the inside of the bed. Ev-
erything else fits as you see in
the guide.
STEP 1
STEP 3STEP 4
STEP 2
STEP 4STEP 5

NEED HELP? 855-680-9595
INSTALLATION MANUAL
STEP 6:Next, grab the 19mm bolts, washers,
and nuts to install the vertical tire
mount. Hand tighten these as well.
Again they will need to be adjusted
before tightening.
Note: Depending on tire size or
mounting position... you can install
the vertical mount anywhere along
this main bottom rail.
STEP 6
STEP 7:First remove the front or rear end cap
from the bed rail so you can slide in
the mounting hardware.
STEP 8:Slide in the mounting hardware.
There are 2 for the brace mount.
STEP 9:Next having the 13mm/19mm hard-
ware handy on the bedside...align
the vertical brace mount with all the
holes.
STEP 7STEP 8
STEP 9

NEED HELP? 855-680-9595
INSTALLATION MANUAL
STEP 10:Hand tighten the 13mm side bed rail
nuts for the vertical brace.
STEP 10
STEP 13:Next tighten the vertical brace to the
vertical carrier with a 19mm socket and
wrench.
STEP 11:Now slide through the 19mm bolts and
hand tighten the 19mm nuts.
STEP 13
STEP 11
STEP 12:Next if the carrier is in its desired
place...start at the side bed rail and
tighten the 13mm hardware.
STEP 12

NEED HELP? 855-680-9595
INSTALLATION MANUAL
STEP 14:Next using the same 19mm socket
and wrench, tighten the bottom of
the vertical carrier to the bottom
main rail.
STEP 14
STEP 16:Now insert the tire screw mount
and rotate so it sets in place vertically...
see photos.
STEP 15:Now move to the bottom main rail
brackets and using the 16mm socket
tighten all the hardware front and back.
STEP 16
STEP 15

NEED HELP? 855-680-9595
INSTALLATION MANUAL
STEP 17:Move the tire into place with the back
facing the vertical carrier.
STEP 18:Slide the rubber cone into place from
the front side of the tire.
STEP 19:Slide the large round steel plate into
place and with the handle angled to-
ward you...tighten down the tire until
very snug.
STEP 17 STEP 18
STEP 19 STEP 20
STEP 20:You’re done! Insure all hardware is
secure and that the tire is fully set
so it doesn’t move. Enjoy!