DV8 OFFROAD LPBM-02 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
FLIP-UP LICENSE
PLATE BRACKET
UNIVERSAL
LPBM-02
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- 4, #8 Allen head sockets
- 10, 19mm Wrenches
- Snap-ring Pliers
- Safety Glasses
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you)
Little skill level required, you can
easily install it by yourself however,
additional help will be useful.
- .5 Hour
Time to install this should only
take about half an hour.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Vehicles equipped with a
winch pull 1 foot of cable out.
If the vehicle is not equipped with a winch
please skip to step 8.
STEP 2 | Using snap-ring pliers,
remove winch shackle hook snap-ring
and shackle pin.
Take caution not to lose the snap-ring
upon removal. It very easy to accidentally
release the load on the pliers and allow
the snap ring to y off and never be found.
Set aside shackle pin and snap-ring to be
reinstalled later.
Begin by unpacking all items and inspecting
for missing pieces or damage. If you have any
concerns, please contact the company the
product was purchased from. Extra hardware
may be included with the product.
(2) M12x40mm Bolts
(2) M12 Lock Nuts
(4) M12 Flat Washers
(4) M6x12mm Bolts
(4) M6 Lock Washers
(8) M6 Flat Washers
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 3 | Remove winch fairlead using
proper tools.
Tools may vary based off fairlead
application.
STEP 4 | Feed winch cable through
license plate bracket and fairlead,
install license plate bracket sandwiched
between the bumper and fairlead.
Loosely secure the fairlead and license
plate to the bumper using a 19mm
wrench, #8 Allen bit and provided M12
hardware.
Note: If you are installing part number
FBJL-09, install the bracket so that it will ip
down instead of up.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 5 | Align license plate bracket
and fairlead with bumper and secure the
M12 hardware using 19mm wrench and #8
Allen bit.
STEP 6 | Reinstall winch cable
shackle hook using snap ring pliers.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 7 | Use winch to take up slack
previously pulled out.
Vehicles equipped with a
winch: Skip to step 10.
Vehicles not equipped with a winch:
Using a 19mm wrench, #8 Allen bit and
provided hardware, loosely secure the
license plate bracket to the front bumper.
Note: If you are installing part number
FBJL-09, install the bracket so that it will ip
down instead of up.
STEP 8 | Align license plate bracket
with bumper and secure the provided M12
hardware using a 19mm wrench and #8
Allen bit.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 9 | Using a #4 Allen bit, 10mm
wrench and provided M6 hardware, secure
the license plate.
Double check that all hardware is secure.
STEP 10 | Congratulations you
are nished with the install of the DV8
Universal Flip-Up License Plate Kit.