DV8 OFFROAD LPBR-05 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
CAPABLE BUMPER LICENSE
PLATE MOUNT
21+ FORD BRONCO
LPBR-05
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- 10, 13mm Wrench
- #4 Allen Bit
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you)
Little skill level required, you can
easily install it by yourself.l
- .5 Hour
Time to install this should only
take about half an hour.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Use a #4 allen bit and 10mm
wrench to secure the license plate to the
bracket.
Then, install the nut caps onto the
exposed nuts by pressing them into place.
Begin by unpacking all items and inspecting
for missing pieces or damage. If you have any
concerns, please contact the company the
product was purchased from. Extra hardware
may be included with the product.
(4) M6x15 Allen
(8) M6 Flat Washers
(4) M6 Nylon Lock Nuts
(2) M5x14 Tapered Allen
(2) M5 Flat Washers
(2) M5 Nylon Lock Nuts
(2) M5 Nut Caps
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 3 | Use a 10mm wrench to
loosen the two factory bolts located
between the bumper and skid plate,
directly below the two front inner sensors
on the bumper.
Loosen them until they are almost
completely removed, but leave a few
threads engaged.
STEP 2 | Use a #4 allen bit and 10mm
wrench to secure the license plate to the
bracket.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 4 | Hook one side of the bracket
to the rst bolt and swing the other side
up into place.
STEP 5 | When the bracket is pushed
up into place, slide it to the driverside and
then pull it down to seat it into place.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 6 | Use a 13mm wrench to
secure the factory hardware.
STEP 7 | Congrats! You are nished
with the install of the 21+ Bronco Capable
Bumper License Plate Bracket.