DV8 OFFROAD STJL-05 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
FOOT PEGS (PAIR)
07+/20+ JEEP WRANGLER/GLADIATOR
JK/JL/JT
STJL-05
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- #6 Allen Bit
- 17mm Wrench/Socket
- T40, T50 Torx Bit
- Trim Clip Tool
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can
easily install it by yourself however,
additional help will be useful.
- .5 Hours
Time to install this should only
take about half an hour.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Roll down your windows
prior to disconnecting the wiring.
This will make lifting the doors off easier
and protect the glass form damage.
Remove the trim panel by pulling towards the
rear of the vehicle until it unclips.
Remove the wire connector by rotating the
white clip until the connector is no longer
locked, and then pull free.
STEP 2 | Now that the wiring harness
has been disconnected, lift on the door
strap to remove it from the hook.
Using a T40 torx bit, remoeve the door check.
Note: Take caution not to damage the vehicle as
the doors may swing towards the front fender.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 3 | Use a T50 torx bit to remove
the bolts securing the doors to the vehi-
cle. With the assistance of another per-
son, lift the door carefully off the vehicle
and set off to the side, being careful not
to damage the door or vehicle.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 4 | Place the foot pegs onto the
factory door hinge.
Note: If these installed on a 07-18 Wrangler JK,
nylon shims are provided to be placed between
the door hinge and foot peg on the top and
bottom of the hinge.
Begin by unpacking all items and inspecting
for missing pieces or damage. If you have any
concerns, please contact the company the
product was purchased from. Extra hardware
may be included with the product.
(2) M10x70 Allen
(2) M10 Nylon Nuts
(4) M10 Flat Washer
(4) M10 Nylon Spacer
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 5 | Installed the provided M10
hardware and secure with a a #6 allen bit
and 17mm socket.
Hardware should be tight enough to
ensure the foot pegs do not shift during
everyday driving, but can be adjusted
inwards and outwards if desired.
STEP 6 | Congrats! You are nished
with the installed of the 07+/20+ JK/JL/JT
Wrangler/ Gladiator DV8 Foot Pegs!