DV8 OFFROAD CCJK-01 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
MOLLE CENTER CONSOLE AND
BRIDGE
07-18 JEEP WRANGLER JK
CCJK-01
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- 3mm Allen
- 1/4” Drill Bit
- Rivnut Tool
- Safety Glasses
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
- 1 Hour
Time to install this should only
take about an hour
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Assemble the center console
on a work bench using a 3mm allen bit or
wrench and the provided M5 hardware.
Use (1) washer with each allen head M5
bolt.
Begin by unpacking all items and inspecting
for missing pieces or damage. If you have any
concerns, please contact the company the
product was purchased from. Extra hardware
may be included with the product.
(14) M5x14mm Allen head
bolts
(14) M5 Washers
(8) M5 x12 Nutserts
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 2 | With the DV8 Center
Console assembled, place the center
console over the gear selector.
STEP 3 | With assistance, hold
the assembly in the desired mounting
location and mark the (4) mounting holes
on each side of the assembly.
Do not let the assembly shift while
marking the mounting holes.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 4 | Remove the DV8 Center
Console.
With a rm grip, pop the factory center
console up.
STEP 5 | Using a 1/4” drill bit, drill (8)
holes where previously marked.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 6 | Install the (8) provided M5
nutserts using a Hand Rivet Nut Setter.
STEP 7 | Secure driver-side center
console panel using a 3mm Allen bit or
wrench and provided M5 hardware.
Use (1) washer per Allen head screw.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 8 | Install the assembled
passenger-side panel & bridge.
Secure passenger-side panel and bridge
using a 3mm Allen bit or wrench and
provided M5 hardware.
STEP 9 | Secure the driver-side panel
to the center console bridge using a 3mm
Allen bit or wrench and the provided M5
hardware.
Double check that all hardware is secure.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 10 | Congratulations,
installation of the CCJK-01 Center Console
is now complete.