DV8 OFFROAD MPJL-01 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
Rear Window Molle Panels
2018+ JEEP WRANGLER JL
MPJL-01
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- Ratchet
-3mm, 4mm Allen Bit
-10mm Wrench
-T50 Torx Bit
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
- 1.5 Hour
Time to install this should only
take about an hour and a half.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Install the smaller bracket
using the provided M6 hardware. All M6
hardware will be nger tight until the end
of install.
Pictured is assembly and installation of
the passenger side panel. They can be
differentiated by looking at which way the logo
is facing.
Begin by unpacking all items and
inspecting for missing pieces or damage. If
you have any concerns, please contact the
company the product was purchased from.
-(10) M6x16 Allen Head
-(20) M6 Flat Washers
-(10) M6 Nylon Lock Nuts
-(2) M4x16 Philips Head
-(2) M4 Flat Washers
-(2) M4 Split Washers
-(2) M4 Nuts
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 2 | Install and secure the
bumpstop using the provided M4
hardware and a 3mm allen bit. The bump
stop should be installed on the same side
as the smaller bracket.
STEP 3 | Install the larger bracket on
the side opposite the bumpstop using
provided M6 hardware. The smaller corner
should be parallel with the logo
Finger-tight only.
STEP 4 | Moving to the interior of the
vehicle, remove the plastic trim on the
seat belt pulley.
Use a T50 to remove the bolt securing the
seatbelt.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 5 | Use a T50 to remove the
two bolts securing the hardtop, located
closest to the front of the vehicle.
STEP 6 | Maneuver the panel into the
approximate location of install and very
loosely secure it with the factory hardtop
bolts by hand.
STEP 7 | Move the seatbelt bracket
into place, and then install the seatbelt
over it.
It may be necessary to apply some force
to get the bracket into position.
Secure the bracket with the seat belt
using a T50 and the factory bolt. Torque to
24 ft-lbs with a dab of blue loctite.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 8 | Finish securing the factory
hardtop bolts with a T50.
Secure all M6 hardware with
4mm allen bit and 10mm wrench.
Replace plastic trim on the seat belt.
STEP 9 | You are now nished
installing your new 2018+ JL Jeep Wrangler
Rear Window Interior Molle Panel.