DV8 OFFROAD SRJK-08 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
OE PLUS SIDE STEPS
07-18 JEEP WRANGLER JK 4-DR
SRJK-08
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- 13mm Socket
- 10mm Wrench/Socket
- 11/32” Drill Bit
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 2 persons
Little skill level required, you can
install it by yourself however,
additional help is recommended.
- 1.5 Hours.
Time to install this should only
take about an hour and a half.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Remove factory steps or
sliders, if equipped, prior to beginning
installation of DV8 OE Plus Side Steps.
On some vehicles, slight drilling may be
required to t DV8 steps properly.
To determine if drilling is necessary, align
the slider with the vehicle and insert the
studs at the rear of the step into the holes
on the pinch weld.
Then line-up the middle and front studs
and check if they can be slid into place. If
the tment is very close, a bit of force can
help manipulate the studs into place.
If they will not slide into place even with
some force applied, remove the sliders
and set off to the side to prepare for
drilling.
Note: Assistance is recommended to prevent
injury and damage to the product or vehicle.
Begin by unpacking all items and inspecting
for missing pieces or damage. If you have any
concerns, please contact the company the
product was purchased from. Extra hardware
may be included with the product.
(6) M8x25 Hex
(12) M8 Nuts
(6) M8 Flat Washers (Wide)
(12) M8 Flat Washers
(18) M8 Spring Washers
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 2 | Drill out the front mounting
holes on the pinch weld using an 11/32”
drill bit.
If necessary, step up to a slightly larger
drill bit, but for our application an 11/32”
drill bit was enough to get our studs
through the pinch weld.
STEP 3 | Re-install the steps by
guiding the studs through the pinch
welds.
Secure the steps main mounting brackets
to the body of the vehicle using the
provided M8 hardware with a 13mm
socket.
Use the wider M8 washers with this
hardware.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 4 | Secure the steps to the
pinch welds using the remaining provided
M8 hardware with a 10mm wrench/socket.
STEP 5 | Congrats! You are nished
with the install of the 07-18 Jeep Wrangler
JK OE Plus Side Steps.