DV8 OFFROAD RBJL-13 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
JL FULL WIDTH REAR BUMPER
2018+ JEEP JL WRANGLER
RBJL-13
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- Rubber mallet
- 22g wire (10-14”) and connectors
(2-6pcs)
- Zip ties
- Electrical tape/wire loom
- 8, 16, 18, 19, 21mm Sockets
- 10mm, 18mm, 21mm Wrench
- #4 Allen Bit
- Wire Cutters
- Phillips Head Screw Driver
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Intermediate
- 2 persons
- 3 Hours
Time to install this should only
take about three hours.
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?
Little skill level required, however,
additional assistance is required for
removal and installation of bumper.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Disconnect the wiring
harness for the license plate light.
This is located inside the bumper behind
the license plate.
STEP 2 | Disconnect the bumper
wiring harness using a panel clip tool
or at screwdriver to pry open the white
locking clip and remove.
Use a panel clip removal tool to
disconnect the two clips securing the
wiring to the vehicle.
This is located behind the bumper on the
driver-side of the vehicle.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 3 | Use a 8mm socket to
remove the bolts securing the rear inner
fender covers.
STEP 4 | Use a 16mm socket to
remove the bolts securing the bumper
brackets to the bumper. These are located
on the edges of the bumper behind the
rear tires.
STEP 5 | Use a 16mm socket to
remove the remaining four bolts securing
the bumper to the vehicle located
between the bumper and rearmost body
mount.
NOTE: Bumper may become loose while
removing these bolts. Assistance is
recommended to prevent injury and
damage to the vehicle or product.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 6 | Remove the remaining
brackets from the frame rails using either
an 18mm or 21mm socket.
Note: The tool required may vary based on
model.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 7 | If equipped with factory
backup sensors, begin by removing the
harness from factory bumper to prepare
for install. Skip to step 13 if not equipped
with factory sensors.
If equipped with factory metal bumper,
you will be able to reuse the sensor
bezels/mounts. If equipped with factory
plastic bumpers, we highly recommend
using OE sensor bezels or DV8 part
#MPRSNSR-01.
Lay out the harness ensuring the main
plug for the harness is on the driver-side
of the bumper. Push out the DV8 sensor
plugs towards the front of the bumper.
Begin by unpacking all items and
inspecting for missing pieces or damage. If
you have any concerns, please contact the
company the product was purchased from.
(4) M14x35 Hex Bolts
(2) M14 Nylon Lock Nuts
(2) M14 Spring Washers
(6) M14 Flat Washers
(2) M14 Nut Plates
(2) M12x45 Hex
(2) M12 Spring Washers
(2) M12 Flat Washers
(7) M6x20 Allen
(14) M6 Flat Washers
(7) M6 Nylon Lock Nuts
(2) M4x15 Philips Head
Bolts
(2) M4 Flat Washers
(2) M4 Spring Washers
(2) M4 Nuts
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 8 | Push the sensor bezels
into place. The outside bezels should be
facing downwards, and the two inside
bezels should be facing down and
inwards away from the d-ring.
A rubber mallet can be used to lightly tap
them into place. The bezels should be at
against the bumper.
STEP 9 | With the bezels in place, run
the sensor wiring harness though cavity
in the bumper aligning the sensors with
the bezels. Push Sensors into bezels
ensure they have “clicked” into place.
Secure sensor harness using provided zip
tie tabs.
Note: If your jeep has factory metal bumpers,
one of the wires in the harness will need to be
lengthened. If equipped with factory plastic
bumpers, Skip to step 13.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 10 | If your bumper was
equipped with factory metal bumpers,
you will need to pull back the wire cover
on the driver-side inside sensor until all
wires are exposed.
This wire will need to be lengthened 5-10”.
STEP 11 | Using wire cutters, cut the
wire and prepare ends for wire connectors.
Using the 22g wire, crimp connectors
to your wire extension (we used non-
insulated connectors and heat shrink for
this install).

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 12 | Insert the extension
between the cut wire and secure. Re-wrap
harness and continue with the install.
If you have any questions, please reach
out to our tech team for assistance.
STEP 13 | If installing light pods,
using the hardware provided with the
lights, install them to the mounts at this
time.
For this install, we are using (2) 3” elite pod
lights.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 14 | Mount the provided
license plate mount to the bumper using
the M6 hardware include with the kit.
Secure hardware using a #4 allen and
10mm wrench .
STEP 15 | Install the provided foam
onto the license plate light.
Then, install the provided license plate
light on to the license plate mount using
the M4 hardware and a Phillips screw
driver.
STEP 16 | To connect the license
plate light, cut off the factory license plate
light plug and either cut back the factory
wire loom to expose more wire length, or
use 22g wire to extend the harness.
Using connectors, connect the factory
harness to your new license plate light.
Cover in wire loom or electrical tape. Zip
tire to backside of license plate mount.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 17 | Place the provided nut
plate into the passenger side of the frame
with the nuts facing upwards.
STEP 18 | Install the mounts onto
the bumper. Using the provided M12
hardware and nut plate.
The nut plate will be used for the top bolts
on both sides.
Leave mounts somewhat loose to proper
alignments on Jeep.