DV8 OFFROAD MPT3-01 User manual

6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM
PRODUCT
INSTALLATION MANUAL
4RUNNER REAR WINDOW
INTERIOR MOLLE PANEL
2010+ (5TH GEN) TOYOTA 4RUNNER
MPT3-01
TOOLS REQUIRED SKILL LEVEL TIME REQUIRED
- 4mm Allen Bit
- 10mm Wrench
- 10mm Socket
- Trim Clip Tool
- Philips Head Screwdriver
Before you install this kit — Read and understand all
instructions, warnings, cautions, and notes contained in
this installation instruction guide. Consult your vehicle
owner’s manual for proper disconnection of electrical and
lifting of vehicle if required for installation of this product.
This install may require some technical skills and
knowledge of basic mechanical work. If you do not feel that
you are capable of performing this install please take this
product to a trained professional.
After reading this guide please contact us with any
questions or concerns before installing product.
Customer Service: 855-680-9595
DV8 Offroad is not responsible for any bodily injury or harm to you
or your vehicle as a result of an improper install.
Proper installation of this kit required knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand during
the installation. Installation of this kit without proper knowledge of the
factory recommended procedures may affect the performance of these
components and the safety of the vehicle
• Always wear eye protection when operating power tools
Inspect all contents of this package to make sure product is not damaged
and all installation hardware has been included. If parts are missing from
kit, please be prepared to provide the following information
1. Name of purchase location
2. Bar Code on side of box
3. Date above bar code
4. Date inside box cover
- Novice/Intermediate
- 1 (you) to 2 persons
Little skill level required, you can
easily install it by yourself however,
additional help will be useful
- 1.5 Hours
Time to install this should only
take about an hour and a half
WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION
855-680-9595
NEED HELP?

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 1 | Install the upper mounting
bracket to the molle panel using the
provided M6 hardware with a 4mm allen
bit and 10mm wrench.
Pictured is the installation of the passenger
side molle panel.
Begin by unpacking all items and
inspecting for missing pieces or damage. If
you have any concerns, please contact the
company the product was purchased from.
(12) M6x20 Allen
(4) M6X25 Allen Head
(16) M6 Nylon Lock Nuts
(32) M6 Flat Washers
(4) Aluminum Spacers
HARDWARE INCLUDED

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 2 | Install the larger “L” shaped
bracket onto the upper mounting bracket
using the provided M6 hardware with a
4mm allen bit and 10mm wrench.
STEP 3 | Use a trim clip tool to
remove the cover of the plastic hanger.
Use a 10mm socket to remove the bolt
and hanger.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 4 | Use a trim clip tool to
remove the plastic cover located
underneath the rear window.
Use a 10mm socket to remove the bolt
located behind the cover.
STEP 5 | Remove the plastic tie down
next to the rear lift gate door by turning it
to unlock, and pulling it out.
Remove the screw behind the plastic tie
down with a phillips head screwdriver.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 6 | Install the aluminum
spacers and secure tightly by hand.
The stepped spacer will be used in the
rearmost (closest to the rear of the
vehicle) factory mounting location.
STEP 7 | Begin installing molle panel
by securing it to the factory mounting
location above the rear window using the
factory bolt and a 10mm socket.

INSTALLATION MANUAL
NEED HELP? 855-680-9595
STEP 8 | Secure the molle panel to
the aluminum spacers using the provided
M6 hardware and a 4mm allen bit.
STEP 9 | Congrats! You are nished
with the install of the 2010+ (5th Gen)
Toyota 4Runner Rear Window Interior
Molle Panel