Dynojet Power commander V User manual

2013 Arctic Cat 450cc/500cc - PCV - 1I11-016.01 www.powercommander.com
Installation Instructions
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE
POWER COMMANDER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 [phone] www.powercommander.com
PARTS LIST
1 Power Commander
1 USB Cable
1 CD-ROM
1 Installation Guide
2 Power Commander Decals
2 Dynojet Decals
2 Velcro
1 Alcohol swab
1 Posi-tap
2013 Arctic Cat 450cc/500cc ATV

I11-016.01 www.powercommander.com 2013 Arctic Cat 450cc/500cc - PCV - 2
EXPANSION PORTS 1 & 2
Optional Accessories such as
Color LCD unit or Auto tune kit.
POWER COMMANDER V
INPUT ACCESSORY GUIDE
Map The PCV has the ability to hold two different
base maps. You can switch on the fly between
these two base maps when you connect
a switch to the MAP inputs. You can use
any open/close type switch. The polarity of
the wires is not important. When using the
Autotune kit, one position will hold a base map
and the other position will let you activate the
learning mode. When the switch is “CLOSED”
Autotune will be activated.
Shifter Not used for this application.
Speed If your application has a speed sensor then
you can tap into the signal side of the sensor
and run a wire into this input. This will allow
you to display vehicle speed in PCV control
center software and on the LCD accessory.
Analog This input is for a 0-5v signal such as
engine temp, boost, etc. Once this input
is established you can alter your fuel curve
based on this input in the control center
software.
Crank Do NOT connect anything to this port unless
instructed to do so by Dynojet. It is used to
transfer crank trigger data from one module to
another.
ACCESSORY INPUTS
CRANK
ANALOG
SPEED
INPUT 1
INPUT 1
INPUT 2
INPUT 2
USB CONNECTION
Wire connections:
1. Remove the rubber plug on the backside of the
unit and loosen the screw for the corresponding
input.
2. Using a 22-24 gauge wire, strip about 10mm
from its end.
3. Push the wire into the hole of the PCV until it
stops and then tighten the screw.
4. Make sure to reinstall the rubber plug.
Note: If you tin the wires with solder it will make
inserting them easier.

I11-016.01 www.powercommander.com 2013 Arctic Cat 450cc/500cc - PCV - 3
2013 Arctic Cat 450cc Installation
Use the following instructions to install the 2013 Arctic Cat 450cc PCV module.
1 Remove the side panels and seat.
2 Remove the two screws securing the gas tank shroud and the single bolt
securing the gas tank to the frame as shown in Figure B.
3 Prop the fuel tank up slightly to gain access to the injector connection.
4 Using the supplied velcro, secure the PCV under the seat as shown in
Figure C.
Make sure to clean both surfaces with the alcohol swab before attaching.
5 Attach the ground wire from the PCV harness to the negative terminal of the
battery as shown in Figure C.
6 Route the PCV harness under the gas tank toward the front of the machine.
FIG.A
FIG.B
FIG.C

I11-016.01 www.powercommander.com 2013 Arctic Cat 450cc/500cc - PCV - 4
7 Locate the injector on top of the throttle body from the right hand side of the
ATV as shown in Figure D.
8 Unplug the stock wiring harness from the injector.
9 Attach the connectors from the PCV to the injector and the stock wiring
harness.
FIG.D
10 Locate the Throttle Position Sensor (TPS) on the left
hand side of the throttle body.
11 Using the supplied posi-tap, attach the grey wire
from the PCV to the green/black wire from the TPS.
12 Reinstall side panels and seat.
13 Insert the cd provided into your computer’s cd-rom
drive and follow the on-screen instructions to install
the PCV software.
Visit www.powercommander.com to download
software tutorials.
FIG.E
2013 Arctic Cat 500cc Installation
Use the following instructions to install the 2013 Arctic Cat 500cc PCV module.
1 Remove the side panels and seat.
FIG.F

I11-016.01 www.powercommander.com 2013 Arctic Cat 450cc/500cc - PCV - 5
2 Remove the two screws securing the tool kit to expose the battery.
3 Using the supplied velcro, secure the PCV under the seat as shown in
Figure G.
Make sure to clean both surfaces with the alcohol swab before attaching.
4 Route the PCV harness under the frame spar toward the front of the machine.
5 Attach the ground wire from the PCV harness to the negative terminal of the
battery as shown in Figure G.
6 Locate the injector on top of the throttle body from the right hand side of the
ATV as shown in Figure H.
7 Unplug the stock wiring harness from the injector.
8 Attach the connectors from the PCV to the injector and the stock wiring
harness.
9 Locate the Throttle Position Sensor (TPS) on the left
hand side of the throttle body.
10 Using the supplied posi-tap, attach the grey wire
from the PCV to the green/black wire from the TPS.
11 Reinstall the tool kit, side panels, and seat.
12 Insert the cd provided into your computer’s cd-rom
drive and follow the on-screen instructions to install
the PCV software.
Visit www.powercommander.com to download
software tutorials.
FIG.G
FIG.H
FIG.I
ground