Dynojet Power commander V User manual

Installation Instructions
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 [phone] www.powercommander.com
22-059 www.powercommander.com 2002-2003 Yamaha R1 - PCV - 1
PARTS LIST
1 Power Commander
1 USB Cable
1 Installation Guide
2 Power Commander Decals
2 Dynojet Decals
2 Velcro strips
1 Alcohol swab
2002-2003 Yamaha R1

EXPANSION PORTS 1 & 2
Optional Accessories such as
POD-300 unit or Auto-tune kit.
POWER COMMANDER V
INPUT ACCESSORY GUIDE
Map - (Input 1 or 2) The PCV has the ability to hold
2 different base maps. You can switch on the
fly between these two base maps when you
hook up a switch to the MAP inputs. You can
use any open/close type switch. The polarity
of the wires is not important. When using the
Autotune kit one position will hold a base map
and the other position will let you activate the
learning mode. When the switch is “CLOSED”
Autotune will be activated. (Set to Switch
Input #1 by default.)
Shifter- (Input 1 or 2) These inputs are for use with the
Dynojet quickshifter. Insert the wires from the
Dynojet quickshifter into the SHIFTER inputs.
The polarity of the wires is not important. (Set
to Switch Input #2 by default.)
Speed- If your application has a speed sensor then
you can tap into the signal side of the sensor
and run a wire into this input. This will allow
you to calculate gear position in the Control
Center Software. Once gear position is setup
you can alter your map based on gear position
and setup gear dependent kill times when
using a quickshifter.
Analog- This input is for a 0-5v signal such as
engine temp, boost, etc. Once this input
is established you can alter your fuel curve
based on this input in the control center
software.
Crank- Do NOT connect anything to this port unless
instructed to do so by Dynojet. It is used to
transfer crank trigger data from one module to
another.
ACCESSORY INPUTS
Wire connections:
To input wires into the PCV first remove the rubber
plug on the backside of the unit and loosen the
screw for the corresponding input. Using a 22-24
gauge wire strip about 10mm from its end. Push the
wire into the hole of the PCV until is stops and then
tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make
inserting them easier.
CRANK
ANALOG
SPEED
INPUT 1 (Grnd)
INPUT 1
INPUT 2 (Grnd)
INPUT 2
USB CONNECTION
22-059 www.powercommander.com 2002-2003 Yamaha R1 - PCV - 2

22-059 www.powercommander.com 2002-2003 Yamaha R1 - PCV - 3
1 Remove the rider’s and passenger’s seat (or solo cover).
2 Lift the front of the fuel tank and prop it up with a prop rod.
3 Locate and unplug the stock 6-pin and 4-pin connectors for the bike’s fuel
injector sub-harness and throttle position sensor (Fig. A).
These connectors are located behind the throttle bodies under the fuel tank on
the left hand side of the bike.
4 Plug the pair of 6-pin connectors on the PCV wiring harness in-line of the
stock 6-pin connectors (Fig. B).
5 Plug the pair of 4-pin connectors on the PCV wiring harness in-line of the
stock 4-pin connectors (Fig. C).
FIG.A
FIG.C
FIG.B
Unplug
Unplug

22-059 www.powercommander.com 2002-2003 Yamaha R1 - PCV - 4
6 Route the PCV wiring harness to the tail section following just inside the left
side frame rail.
7 Secure the PCV ground wire with the ring lug to the negative (-) side of the
bike’s battery (Fig. D).
FIG.D
8 Secure the PCV module inside the tail section, using the supplied Velcro
(Fig. E).
Clean the surface with the supplied alcohol swab prior to applying the Velcro.
9 Lower and secure the fuel tank.
10 Reinstall the seats.
Optional inputs:
Speed - PINK wire from speed sensor. Connector is located under the fuel
tank on the right hand side. Connector has PINK, ORANGE/RED, and BLACK/
WHITE wires.
Temperature - GREEN/WHITE wire on pin #31 of the ECU
12v source for Auto-tune - BLUE wire of taillight connector. Connector is
located by the ECU. It is a WHITE 3-pin connector with BLACK, BLUE, and
YELLOW wires.
FIG.E
PCV Harness
Ground