Ecleris MICROSTAR C-100A5E User manual

USER MANUAL
MICROSTAR SERIE C-100A5E
COLPOSCOPE - FLOOR STAND-TELESCOPIC COLUMN MODEL
ABOUT THIS MANUAL
Version: 2019.04.01
Year: 2019
Language: English
All the rights to this manual are reserved, especially reproduction, publication and translation rights. No portion of this manual may be
reproduced by no means (photocopy, microfilm or other methods) without previous written authorization from ECLERIS. Neither can it
be reproduced, multiplied or published through any electronic data processing form.
The information contained in this manual may be modified or broaden without previous notification, without it representing any
responsibility to ECLERIS.
EUSA GLOBAL Llc.
11801 NW 100th Rd
Suite 17
Medley, FL 33178, U.S.A.
Phone: [phone]
CMC Medical Devices & Drugs S.L.
C/ Horacio Lengo Nº18, CP29006,
Málaga, Spain
Ph. [phone]
Email: [email protected]

USER MANUAL –COLPOSCOPE C100A5E
Page 2of 20
INMANUUIN163 Rev.2019.04.01 / ENG
TABLE OF CONTENT
1. SYMBOLS................................................................................................................................4
2. SECURITY WARNINGS ..........................................................................................................4
2.1 WARNINGS..........................................................................................................................4
3. DESCRIPTION.........................................................................................................................5
3.1 INTENDED USE...................................................................................................................5
3.2 INTENDED USER ................................................................................................................5
3.3 DESCRIPTION AND COMPONENTS ..................................................................................5
3.3.1 FLOOR STAND - TELESCOPIC COLUMN MODEL –C-100A5E .................................6
3.3.2 COMPLETE HEAD........................................................................................................7
3.3.3 LIGHT SOURCE............................................................................................................7
3.3.3.1 FRONT PANEL..........................................................................................................7
3.3.3.2 REAR PANEL............................................................................................................8
3.3.4 COMPATIBLE ACCESORIES.......................................................................................8
4. INSTALLATION AND SET UP .................................................................................................8
4.1 FLOOR STAND - TELESCOPIC COLUMN MODEL –C-100A5E.........................................9
4.2 FOCAL LENS MOUNTING.................................................................................................11
4.3 BEAM SPLITTER AND CAMERA INSTALLATION.............................................................11
4.3.1 IMAGE ORIENTATION...................................................................................................13
4.4 REVISION..........................................................................................................................13
5. OPERATION –FUNCTIONS .................................................................................................13
5.1 INTERPUPILLARY DISTANCE ADJUSTMENT..................................................................14
5.2 DIOPTRIC CORRECTION ADJUSTMENT.........................................................................14
5.3 MAGNIFICATION VARIATION...........................................................................................14
5.4 COLOR FILTER .................................................................................................................14
6. MANIPULATION & MOVEMENTS.........................................................................................15
6.1 HEAD ROTATION AXIS.....................................................................................................15
6.2 HEAD TILT.........................................................................................................................15
6.3 SHIPMENT.........................................................................................................................15
7. MAINTENANCE.....................................................................................................................15
7.1 CLEANING.........................................................................................................................16
7.1.1 CLEANING THE EXTERNAL SURFACES..................................................................16
7.1.2 CLEANING OF OBJECTIVE LENS AND EYEPIECES................................................16
7.2 ELECTRICAL CONNECTIONS..........................................................................................16
7.3 FUSE REPLACEMENT......................................................................................................17
8. TECHNICAL SPECIFICATIONS............................................................................................17
9. TROUBLESHOOTING...........................................................................................................18
10. TECHNICAL SERVICE.......................................................................................................19

USER MANUAL –COLPOSCOPE C100A5E
Page 3of 20
INMANUUIN163 Rev.2019.04.01 / ENG
11. WARRANTY.......................................................................................................................20

USER MANUAL –COLPOSCOPE C100A5E
Page 4of 20
INMANUUIN163 Rev.2019.04.01 / ENG
1. SYMBOLS
Read the related documentation
CE mark
Warning!
Manufacturers information
(Name, Address)
Alternate current
BF type
Protect from water
Do not discard with the
household waste
This side up
Protective Earth (Ground)
Environmental transport conditions
Equipotentiality
Fragile
I
ON
Serial number
OFF
Manufacturing date (MM/YYYY)
Catalogue number
2. SECURITY INFORMATION
2.1 WARNINGS
It is very important to read carefully this manual before using the Ecleris Microstar C-100A5E
Colposcope.
The Ecleris Microstar C-100A5E Colposcope is an electrical device that provides very high light
intensity. Its use is recommended exclusively for trained personnel.
ECLERIS will not assume any liability for damages that may occur if the device is used without
following the instructions and/or ignoring the following advice:
Keep the device out of children reach.
Do not install the device close to heat sources like stoves.
Do not use the colposcope in places where there is explosion danger.
Always install the device on top of firm and horizontal surfaces, on a perfect ventilated
area.
Do not block the ventilation screens. This ventilation must assure good air flow.
Avoid device exposure to direct sunlight, dust, humidity, vibration or shock.
Do not put any container with liquids on top of the device; do not expose the device to
rain or sun.
Do not bend or tie a nut on the power cable, or any cable connected to the device.
Do not use the device during thunderstorms.
After the use of the device, turn it off and disconnect the power cable.
In order to avoid electrical shocks, this system must be connected to a power grid with
proper ground connection (no exceptions).
This system is not designed to be used in the presence of inflammable anesthetic gases
mixture with air, oxygen, nitrous oxide or environments with high oxygen content.

USER MANUAL –COLPOSCOPE C100A5E
Page 5of 20
INMANUUIN163 Rev.2019.04.01 / ENG
The device is provided with a connectable power cable that assures proper electrical
isolation on the grid.
In the case of electromagnetic interference between the medical device and other
electrical devices, we recommend increasing the distance between the systems in order
to minimize the interference effects.
Do not open the device. The diagnostics, service and repairment must be performed by
ECLERIS, or a company authorized by ECLERIS. ECLERIS will not be liable for the
damage caused by repairment, or service performed by unauthorized personnel.
In case of any problem, the system must be laid on a plane surface and the must power
cable disconnected.
The device must be used only by personnel informed of all this warnings.
Any use outside of the manufacturer specific intent use, will exclude ECLERIS of all
liability.
This user manual must be with the device for permanent review. If the system is sold or
donated, the user manual must be delivered with the device.
Although the light source does not damage the eyes, it is recommended not to look
directly into the light channel or the end of the colposcope; and handling it according to
instructions.
If as a consequence of:
Inadequate use of the equipment.
No use of this manual.
Poor care and maintenance of the equipment.
Repair and manipulation by unauthorized personnel.
…any material or personal damage were caused to third parties, ECLERIS, the manufacturer and
the supplier of the equipment, shall not assume any responsibility for such damages.
Do not dispose of the device, or any of the accessories with the domestic waste.
Research the local rules and laws for proper disposal. It is the user’s responsibility
to deliver the system to the proper location for disposal or recycling of electrical and
electronic devices or contact the manufacturer or authorized representative to
proceed on the elimination of the system on a safe and ecological way.
3. DESCRIPTION
3.1 INTENDED USE
The Ecleris Microstar C-100A5E Colposcope has been designed for gynecological diagnosis
observations.
3.2 INTENDED USER
The device has been designed to be used by medical, paramedical or health professionals
3.3 DESCRIPTION AND COMPONENTS
Carefully unpack the accessories and remove them from their packing. Check for missing items
and evidence of shipping damage. File any complaints with the manufacturer or supplier
immediately. Retain the original packing materials for later use. These can come handy when the
equipment must be transported.

USER MANUAL –COLPOSCOPE C100A5E
Page 6of 20
INMANUUIN163 Rev.2019.04.01 / ENG
The Ecleris Microstar C-100A5E Colposcope includes the following necessary components.
Please identify and check them before you proceed with the installation:
3.3.1 FLOOR STAND - TELESCOPIC COLUMN MODEL –C-100A5E
Components:
1 Base with wheels
1 Telescopic Column
1 90° Arm
1 Everlux Mini Light Source
1 Head with 1 objective lens
1 Binocular
2 Eyepieces
1 Fiber optic cable
1 3 mts Power cable
1 Cover
1 User’s manual
1 10 mm Allen key
1 4 mm Allen key
1. Head
2. Head handle
3. Fiber optic cable
4. Regulation of head rotation
command
5. Regulation of elbow rotation
command
6. Height brake
7. Wheels
8. Eyepiece
9. Binocular

USER MANUAL –COLPOSCOPE C100A5E
Page 7of 20
INMANUUIN163 Rev.2019.04.01 / ENG
10. Elbow (90º piece)
11. LED light souce 12. Column 13. Base
3.3.2 COMPLETE HEAD
1. Magnification selector
2. Micro focus adjustment
3. Objective lens
4. Green filter
5. Head handle
6. Fiber optic cable
7. Eyepiece rubber
8. Eyepiece
9. Binocular body
10. Head body
11. Balance movement control
12. Head fork pole
3.3.3 LIGHT SOURCE
3.3.3.1 FRONT PANEL
1. On/Off switch
2. Light Intensity Control (Dimmer) 3. Fiber optic cable connector 4. Camera connector (video input)

3.3.3.2 REAR PANEL
5. Earth connection
6. Power supply cable connector with
fuse holder
7. Ventilation grid
8. S-Video Output (SVHS)
9. Composite Video Output (CVBS)
10. Ecleris EndoDigi connector (image
and video capture) and other
peripheral devices *
* Standard output (Normally-Open) to remotely operate other image capture devices such as
Video Printers.
3.3.4 COMPATIBLE ACCESORIES
Beam splitter.
Digital photographic camera adapter.
Converter of beam splitter to endocoupler C-Mount.
45º inclined binocular.
Straight binocular.
CCD Video Camera (NTSC/PAL).
Eyepieces 10X.
200 mm Objective lens.
250 mm Objective lens.
300 mm Objective lens.
400 mm Objective lens.
Digital capturing and documentation system –Ecleris ENDODIGI.
4. INSTALLATION AND SET UP
Experienced personnel are not required for the installation of the Ecleris Microstar C-100A5E
Colposcope.
To avoid accidents while handling heavy parts of the equipment, two people should
perform the installation of the Colposcope, carefully following the enclosed instructions.

USER MANUAL –COLPOSCOPE C100A5E
Page 9of 20
INMANUUIN163 Rev.2019.04.01 / ENG
Once the installation is over, please continue with the procedures detailed in the Revision section.
4.1 FLOOR STAND - TELESCOPIC COLUMN MODEL –C-100A5E
1) Place the colposcope's base in a vertical position.
2) Insert the column into the base and hold it by mean of the provided 10mm Allen screw. Place
the washer between the screw and the base as shown in the picture below
3) Stand the base on the floor and insert the 90° arm into the column.
4) Attach the light source to the column using the 4 Phillips screws provided.
5) Insert the head fork into 90° arm.

USER MANUAL –COLPOSCOPE C100A5E
Page 10 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
6) Place the binocular in the matching binocular support, verifying that the marks are aligned.
Adjust the binocular screw to achieve the best possible seat.
7) Attach the eyepieces to the binocular. Unfold the rubber protectors surrounding the
eyepieces.
Note: If the user wears eyeglasses, leave the rubber protectors folded.
8) Attach one end of the fiber optic cable to the light source and the other end to the head.

USER MANUAL –COLPOSCOPE C100A5E
Page 11 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
If you detect any abnormality before you start operating the Ecleris Microstar C-100A5E
Colposcope, please contact the technical department of your local distributor or nearest
ECLERIS office prior to using the colposcope on patients.
4.2 FOCAL LENS MOUNTING
Screw the lens to the head, tightening until the micro focus adjustment reaches the desired
position. Counterscrew the nut for proper fixation of the lens.
4.3 BEAM SPLITTER AND CAMERA INSTALLATION
1) Remove the binocular if it is already placed.
2) Tightly screw the camera to the beam splitter until its end.
Do not over tight the video camera to the beam splitter in order to avoid mechanism
damage.
3) Place the beam splitter with the camera verifying that the marks are aligned. Adjust the beam
splitter screw to achieve the best possible seat.

USER MANUAL –COLPOSCOPE C100A5E
Page 12 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
4) The same way, place the binocular on top of the beam splitter.
5) Connect the video cable to the video output on the light source.
6) Connect the other end of the video cable to the monitor’s video input (Video IN).
7) Turn on the light source and monitor.
8) Locate the head at the working distance according to the focal lens (200, 250, 300 or 400
mm) and focus a flat image or object. Working distance must be measured from the focal lens
to the object. It is very important to use a flat object or image during this procedure.
9) Set the oculars to its middle position (no dioptric correction).
10) Rotate the magnification selector up to the maximum factor (2.5X).
11) Looking through binoculars, focus the image using the micro-focus knob until all
magnifications are in focus (parafocusing).
12) Adjust the oculars dioptrics to correct eyesight deviations, until the visualized image gets
comfortable and sharp.
13) After the optical image is parafocused (all magnifications in focus), adjust the camera
position until its image reaches the same orientation as the optical image (see image
orientation).
14) Rotate the magnification selector up to the maximum factor (2.5X).
15) Focus the camera’s image using the beam splitter focus control until all magnifications are in
focus.

USER MANUAL –COLPOSCOPE C100A5E
Page 13 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
Important:
The optical Head is parafocused only at the working distance according to the used
focal lens. Deviations in working distance will affect the optical parafocusing and focus
adjustment should be repeated.
4.3.1 IMAGE ORIENTATION
To give the monitor’s image the same orientation seen through the binocular, follow these steps:
1) Loose the 3 Allen screws in the beam splitter by using the supplied 1.5mm Allen key.
2) Rotate the video camera until the orientation of the image visualized through the binoculars is
the same as the image on the monitor.
3) Adjust the 3 Allen screws of the Beam splitter to fix the camera position.
4.4 REVISION
Once installation is over and before starting-up the Ecleris Microstar C-100A5E Colposcope,
please go through the following check list:
Check that the voltage to be used is within the specified power voltage range.
Verify that the electrical network used has its grounding connection in perfect conditions
and that it makes perfect contact with the equipment.
Check that the fuse holder has fuses installed and that are the correct ones (2 x
T3AL250V).
Check that the ventilation grid of the light source is completely free, without obstruction.
Ensure an adequate air flow.
Verify that there are no water or liquid sources near the equipment that may damage it,
such as gases or flammable emissions in the environment.
If before connecting the Ecleris Microstar C-100A5E Colposcope any anomaly is
detected, please contact the technical service department of your local distributor or the
closest ECLERIS office, prior to its use.
5. OPERATION –FUNCTIONS
This section thoroughly describes the equipment functioning.

USER MANUAL –COLPOSCOPE C100A5E
Page 14 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
This system must be used only for medical, or paramedical applications, it should only be
used by health professionals.
1) Insert the thinner end of the fiber optic cable into the colposcope’s head and the other end to
the light source.
2) Connect the power supply cable to the equipment and the electrical network.
3) Turn the light source on by pressing the ON/OFF switch in the front panel.
4) Turn the LED system on by turning the light intensity control (dimmer) clockwise.
5) Use this control to regulate the light intensity.
The EVERLUX Mini light source has an over-temperature protection. LED system will turn
off if it reaches a risky operation temperature.
6) Once the procedure is over, turn the EVERLUX Mini off in order to maximize the LED system
lifetime and energy saving.
Fans should always be working while the light source is turned on. If for any reason they
do not operate, turn the light source off immediately to avoid a failure due to high
temperature.
While the colposcope is not being used, the light source should be turned off.
Never touch the fiber optic end.
Do not look directly into the end of the light guide cable or the end of the objective lens of the
colposcope.
It is recommended to connect the fiber optic cable before you turn on the light source.
5.1 INTERPUPILLARY DISTANCE ADJUSTMENT
To perform this adjustment you must hold the body of the binocular with both hands and turn
them simultaneously. You must move these backwards and forwards until the distance between
them matches your interpupillary distance.
5.2 DIOPTRIC CORRECTION ADJUSTMENT
The Ecleris Microstar C-100A5E Colposcope has independent dioptric correction for both
eyepieces. The adjustment is made by turning the eyepieces towards the + sign or towards the –
sign.
5.3 MAGNIFICATION VARIATION
The magnification selector has six positions: 4/6/10/16/25 x. The 10 x position is repeated in the
selector. The mark on the body of the colposcope will show the selected magnification.
The colposcope’s magnification can be changed with any of the commands located on either side
of the binocular, turning them slowly until you reach the desired magnification.
5.4 COLOR FILTER
If the operator considers it necessary, a color filter can be placed between the light source and
the objective lens by pulling out the proper control.

USER MANUAL –COLPOSCOPE C100A5E
Page 15 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
6. MANIPULATION & MOVEMENTS
The Ecleris Microstar C-100A5E Colposcope has been designed to obtain very stable movements
and proper positioning of the head for better operation.
6.1 HEAD ROTATION AXIS
For a better alignment of the optical axis in relation with the target the head can be rotated on the
forked pole. The rotational range is 0-360 degrees. The movement can be adjusted or completely
locked using the control knob.
6.2 HEAD TILT
The colposcope allows a 180º tilt and has an adjustment knob on the head’s left hand side. This
knob allows a continuous adjustment of the tilt setting or a complete tilt lock to position the
colposcope’s head as desired with a minimum effort thanks to the ball bearings.
Before loosening this command, verify that the fiber optic cable is not strained.
6.3 SHIPMENT
The Ecleris Microstar C-100A5E Colposcope has been designed to be moved over short
distances within a doctor’s office or room. If it is necessary to move the colposcope over larger
distances, special attention should be paid to the following recommendations:
Set the brakes to avoid movements..
Place the cover on the colposcope.
Disconnect the power cable from the electrical network and tie it firmly to the colposcope’s
column.
Do not circulate over slanted surfaces with an angle larger than 10º, avoiding tipping over
the colposcope.
No circule por superficies inclinadas con un ángulo mayor a 10º, evitando el vuelco del
colposcopio.
By following these recommendations accidents during transportation and any further damage to
the colposcope due to incorrect handling will be avoid.
7. MAINTENANCE
To maintain optimum operation of the Ecleris Microstar C-100A5E Colposcope, it is
recommended to perform a simple revision of the equipment once a year.
This procedure should include:
Lubrication.
Cleaning.
Revision of electrical connections.
Spare parts: to avoid loss of time, and an inoperative colposcope, it is recommended to
have a spare lamp and fuse (T3A250V).

USER MANUAL –COLPOSCOPE C100A5E
Page 16 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
To perform any revision or maintenance work, contact your local distributor or the closest
ECLERIS office.
7.1 CLEANING
Before cleaning the Ecleris Microstar C-100A5E Colposcope, disconnect the power
supply cable form the electrical network.
7.1.1 CLEANING THE EXTERNAL SURFACES
Clean the external surface of the equipment using a piece of cotton or cloth moistened with mild
detergent or soap. Use only adequate products for the external cleaning of electrical equipment,
prepared in accordance with the manufacturer’s indications.
Perform the cleaning with special care, avoiding the access of water or humidity to the
equipment.
Do not use flammable products, especially alcohol when the light source is not cold. If flammable
products were used, do not turn the light source on until one (1) hour after the cleaning, since an
explosive mixture may be produced.
Do not use detergents, solvents or any other abrasive agents.
Do not send to the autoclave any part or component of this device that is not specifically marked
as autoclavable.
Do no sterilize or immerse the device or its accessories.
The cleaning, disinfection and sterilization of accessories not provided by ECLERIS must be
performed following the instructions provided by their manufacturer.
It is recommended to clean the exterior surface of the device every 15 days.
7.1.2 CLEANING OF OBJECTIVE LENS AND EYEPIECES
Smoothly rub the lens surface using circular movements with a thin tissue paper moistened in
acetone.
7.2 ELECTRICAL CONNECTIONS
Constantly check the condition of all components and their aging process.
Verify there are no:
Faulty, broken or cut cables.
Faulty connection between the cable and the plug.
Oxide corrosion in connection pins.

USER MANUAL –COLPOSCOPE C100A5E
Page 17 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
7.3 FUSE REPLACEMENT
Disconnect the power cable from the electrical network.
1) Disconnect the power supply cable from the light source.
2) Under the power cable connector is a small rectangular plastic holder where the fuses are
located. With the help of a screwdriver and with slight pressure, remove the lid.
3) Remove the burnt fuse, and replace it. Use a T3A250V fuse.
4) Place the fuse lid back, pushing it until a “click” is heard.
5) Connect the power supply cable to the light source and to the electrical network.
8. TECHNICAL SPECIFICATIONS
MICROSTAR C-100A5E COLPOSCOPE
OPTICAL SYSTEM
Composed of apochromatic lenses with a
fungus-resistant coating
BINOCULAR TUBES
45° Inclined: 55 - 80 mm
Straight: 45 to 80mm
Inclinable: 50 to 85mm
OBJECTIVE LENS
F: 200 / 250 / 300 / 400 mm(one included)
MAGNIFICATIONS
Apochromatic five steps magnification changer
through a click-stop revolving mechanisms
FINE FOCUS
Manual
EYEPIECES
10 X wide angle
Dioptric setting: + / - 5
FIELD OF VIEW (10 X)
Ø 24 mm / 0.95” (for F: 200 mm)
Ø 31 mm / 1.22” (for F: 250 mm)
Ø 36 mm / 1.42” (for F: 300 mm)
Ø 50 mm / 2.00” (for F: 400 mm)
INTERPUPILAR DISTANCE
2.16”- 2.95”
55 - 75 mm
FILTER
GREEN
ILLUMINATION
TYPE OF ILLUMINATION
Coaxial illumination through 7 mm fiber optic
light guide cable
LIGHT SOURCE
High intensity led
Integrated video camera input and video

USER MANUAL –COLPOSCOPE C100A5E
Page 18 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
output
ILLUMINATED FIELD
Ø 70 mm / 2.75” (for f: 200 mm)
Ø 90 mm / 3.54” (for f: 250 mm)
Ø 107 mm / 4.2” (for f: 300 mm)
Ø 145 mm / 5.7” (for f: 400 mm)
POWE SUPPLY
100-240 VAC, 50 / 60 Hz
FUSES
2 x T3AL250V
CLASS
I
APPLICABLE PART
BF type
USE
Continuous
POWER CONSUMPTION
110VA
COLOR TEMPERATURE
6000ºK approx.
LED SYSTEM SERVICE LIFE
50000 hours approx.
REFRIGERATION
Forced
OVER TEMPERATURE PROTECTION
Automatic led system power-off
ILLUMINATION CONTROL
Electronic dimmer
FLOOR STAND - TELESCOPIC COLUMN
BASE
640 x 640 mm
HEIGHT REGULATION
97,5 a 120 mm
WEIGHT
29.7 pounds / 13.5Kg
SERVICE CONDITIONS
TEMPERATURE
50 –104 ºF
HUMIDITY
35 - 75 % relative humidity
PRESSURE
700 - 1060 hPa
STORAGE AND TRANSPORTATION CONDITIONS
TEMPERATURE
-22 –122 ºF
HUMIDITY
10 - 95 % relative humidity
PRESSURE
500 - 1060 hPa
9. TROUBLESHOOTING
The following table indicates the most common problems and their quick solutions. Please consult
this table for any difficulty you may encounter.
PROBLEM
PROBABLE CAUSE
ACTION
The light source does
not work.
It is not connected to the
local electrical network.
The power cable is
broken or cut.
The plug is not in good
Connect the cable to the network.
Change the cable.
Change the plug.

USER MANUAL –COLPOSCOPE C100A5E
Page 19 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
conditions.
The fuse is broken or
burnt out.
Network’s voltage is not
compatible with the one
required.
Change the fuse.
Verify network voltage.
The green pilot light
from the on/off switch
turns on but the LED
system does not.
Exhausted LED system.
Contact the closest Technical
service.
Over-temperature LED
system protection
activated.
Clean and clear the lateral
ventilation grids. Check if the fan is
running.
Turn the equipment off
immediately and contact the
closest Technical Service.
Internal fuse burnt or
defective board.
Contact the closest Technical
Service.
Light intensity is not the
correct one.
Defective LED system.
Contact the closest Technical
Service.
High temperature.
Lateral ventilation grids
are obstructed.
Clear the lateral ventilation grids.
Fan is not working.
Turn the equipment off
immediately and contact the
closest Technical Service.
If the problem cannot be solved, please contact your local distributor or the closest ECLERIS
office and request technical service.
10. TECHNICAL SERVICE
The Ecleris Microstar C-100A5E Colposcope should be repaired and/or maintained exclusively
by ECLERIS trained and qualified personnel in authorized installations and only the parts of the
device that ECLERIS state as repairable must be repaired.
ECLERIS, will provide if required, circuits, drawings, list of components, descriptions and
instructions for calibration or other useful information required by qualified trained technical
personnel, to repair the parts of the device marked as repairable by the manufacturer.
1) Contact the Technical Service Department of your local distributor or the nearest
ECLERIS office.
2) Give detailed information of the problem.
3) If the problem cannot be solved by troubleshooting, the product shall be sent for its
repair.
The following product information shall be attached:

USER MANUAL –COLPOSCOPE C100A5E
Page 20 of 20
INMANUUIN163 Rev.2019.04.01 / ENG
Owner’s name.
Owner’s address.
Contact name and phone number.
Product’s serial number.
Problem’s description.
The Ecleris Microstar C-100A5E Colposcope shall be sent in its original packaging so that it is
not damaged during transportation. ECLERIS shall not be liable for damages that may occur
during transportation, caused by deficient packaging.
The Ecleris Microstar C-100A5E Colposcope life time, based on the spare parts availability,
has been established in 6 years from the date of manufacture.
11. WARRANTY
ECLERIS states that the Ecleris Microstar C-100A5E Colposcope has complied with the
required Quality Control verification and has no manufacturing defects. This guarantees the
appropriate functioning under adequate use in agreement with the indications of this manual.
The warranty period is for one (1) year as from the date of purchase invoice.
ECLERIS shall not be liable for any damage caused to/by the Colposcope due to incorrect
use, negligence, incorrect cleaning or storage.
Any repairs made by personnel not authorized by ECLERIS will void this warranty.
The described warranty is exclusively valid for the original buyer.
The following parts are excluded from the warranty:
Parts and components manufactured by third parties.
Lamps.
Cables and plugs.
Damages resulting from connections to inadequate power supplies.
Disregarding the warranty situation, all shipment from and to the authorized ECLERIS
technical service facilities are the sole responsibility of the client.