Elko RFWB-20/G User manual

WIRELESS SWITCH
(CLASSIC VERSION)
Combination of iNELS wall-mounted wireless controller and switching unit for various uses.
It can be used to remote control electrical appliances, lights, sockets, garage doors, etc.
EN

On-wall button controller PLASTIC - 2 buttons
RFWB-20/G
On-wall button controller PLASTIC - 4 buttons
RFWB-40/G
Switch unit, 1-channel
RFSAI-11B-SL
ON
switch unit
OFF
switch unit
ON
switch unit 1
OFF
switch unit 1
ON
switch unit 2
OFF
switch unit 2
Package
The individual elements in the iNELS kit are paired and their functions are preset.
iNELS kit wireless switch enables the basic function of controlling electrical appliances - ON / OFF.
The settings of the wall controllers can be changed - see detailed manuals of iNELS elements.
Range up
to 200 m
EAN 8595788182878 (On-wall button controller PLASTIC - 2 buttons + 1 switch unit, 1-channel)
EAN 8595188182881 (On-wall button controller PLASTIC - 4 buttons + 2 switch units, 1-channel)

5 6
1 2 3
4
RFWB-40/GRFWB-20/G
On-wall button controller
RFWB-20/G, RFWB-40/G
Characteristics
• The wireless controller is used to control switches and dimmers (lights, gate, garage door, blinds, etc.).
• RFWB-20/G: two buttons enable control one or two units independently (depending on the type of swit-
ching element).
• RFWB-40/G: four buttons enable control from two up to four units independently (depending on the type
of switching element).
• The flat design with level base makes it ideal for fast installation on any surface (fixation with adhesive or
screws in the installation box).
RFWB-20/G – On-wall button controller PLASTIC - 2 buttons
RFWB-40/G – On-wall button controller PLASTIC - 4 buttons
Safe handling
Battery replacement RFWB-20/RFWB-40
Using a screwdriver,
carefully pry o
the device from the
frame.
Gently pull to
remove the cover.
Slide the CR2032
battery into the
battery holder.
Observe the
polarity.
Snap on the cover.
The LED opening
must be located
in the upper part
(for the RFWB-
40, observe the
positioning of the
left and right cover
Place the frame
on the rear part.
Snap the device
with the cover
into the prepared
frame.
When handling a device unboxed it is important to avoid contact with liquids. Never place the device
on the conductive pads or objects, avoid unnecessary contact with the components of the device.
Detailed manual

RFWB-20/G RFWB-40/GTechnical parametres
Attention:
When you instal iNELS RF Control system, you have to keep minimal distance 1 cm between each units.
Between the individual commands must be an interval of at least 1s.
Supply voltage:
Transmission indication:
Number of buttons:
Transmitter frequency:
Signal transmission method:
Range in free space:
Other data
Operating temperature:
Operating position:
Mounting:
Protection:
Contamination degree:
Dimensions:
Weight:
Related standards:
3 V battery CR 2032
red LED
2 4
868.5 MHz
unidirectionally addressed message
up to 200 m
-10 ... +50 °C (14 ... 122 °F)
any
glue, screws
IP20
2
85 x 85 x 16 mm (3.3“ x 3.3“ x 0.6“)
38g * (1.34 oz) 39g * (1.37 oz)
EN 60669, EN 300220, EN 301489 R&TTE Directive,
* Acording to the territory - see the cabel.

RFSAI-11B-SL
Switch unit, 1-channel
RFSAI-11B-SL
Characteristics
• The switching unit with 1 output channel is used to control appliances, lights, etc.
• The BOX design lets you mount it right in an installation box, a ceiling or a controlled appliance cover.
• The switched load up to 8 A (2.000 W)..
• Single-function design - switch on / o.
• The output on the switching unit can be controlled by up to 25 channels (1 channel represents one button on
the controller).
• The programming button on the unit is also used for manual control of the output.
• Memory status can be pre-set in the event of a power failure.
• For components labeled as iNELS RF Control2(RFIO2), it is possible to set the repeater function via the RFAF/
USB service device.
• Communication frequency with bidirectional protocol iNELS RF Control2 (RFIO2).
Installation options
In to the installation box into the ceiling light cover under ceiling mounted
Detailed manual

RFSAI-11B-SL
230 V AC
50-60 Hz
7 VA / cos φ = 0.1 / 0.7 W
1x switching contacts (AgSnO2)
8 A / AC1 / 2000 VA
10 A / <3 s
250 V AC1
button PROG (ON/OFF)
868.5 MHz
-15 ... + 50 °C (5 ... 122 °F)
free at lead-in wires
IP40
III.
43 x 44 x 22 mm (1.9“ x 1.97“ x 0.8“)
31 g
EN 60730, EN 63044, EN 300 220, EN 301 489
Supply voltage:
Supply voltage frequency:
Power apparent / dissipated:
Output:
Number of contacts:
Rated current: / switching power
Peak current:
Max. switching voltage:
Communation:
Manual:
Frequency:
Other data:
Operating temperature:
Mounting:
Protection:
Overvoltage category:
Dimensions:
Weight:
Related standards:
Technical parameters

RFSAI-11B-SL
8 mm
20~16 AWG
0.2 ~1.5 mm2
Compatibility
The device can be combined with devices of iNELS RF Control2with RFIO2protocol.
Connection
Screwless terminals
S - external input
N - neutral wire
L - phase wire
V - output
i- programing button
- manual controll
- output status indication
SLIDE IN
PUSH IN
RELEASE
Solid conductor

60 - 90 % 80 - 95 % 20 - 60 % 0 - 10 % 80- 90 %
x
RFRP-20
Designed & Manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly,
Czech republic, www.elkoep.com, Hotline: [phone]
Radiofrequency signal penetration through various construction materials
brick walls wooden structures
with plaster boards reinforced concrete metal partitions common glass
Range up to 200 m in open space, if the signal is insucient between the controller and unit, use the signal
repeater RFRP-20 or protocol component RFIO2that supports this feature.
Instruction manual is designated for mounting and also for the usage of the device. It is always a part of its pac-
king. Installation and connection can be carried out only by a person with adequate professional qualification
with understanding this instruction manual and functions of the device, and while observing all valid regulations.
Trouble-free function of the device also depends on transportation, storing and handling. In case you notice any
sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller.
It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before
starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting
and servicing observe safety regulations, norms, directives and professional, and export regulations for working
with electrical devices. Do not touch parts of the device that are energized – life threat. Due to transmissivity
of RF signal, observe correct location of RF components in a building where the installation is taking place. RF
Control is designated only for mounting in interiors. Devices are not designated for installation into exteriors
and humid spaces. The must not be installed into metal switchboards and into plastic switchboards with metal
door – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – radio-
frequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get flat etc. and
thus disable remote control.
Warning