Elo TouchSystems 1543L User manual

SW601960 Rev. F, page 1 of 31
User Manual –32/42/43/5543L Series IDS
USER MANUAL
Elo Touch Solutions
32/42/43/5543L IDS Touchscreen Displays`
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Elo 1543L o cerca
il tuo prodotto tra le migliori offerte di Monitor

SW601960 Rev. F, page 2 of 31
User Manual –32/42/43/5543L Series IDS
Copyright © 2017 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by
any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively "Elo") makes no representations or warranties
with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise this
publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch,, SecureTouch,
TouchTools, TouchPro and VuPoint are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft Corporation.

SW601960 Rev. F, page 3 of 31
User Manual –32/42/43/5543L Series IDS
Table of Contents
Section 1: Introduction...................................................................................................................................................................................................................................4
Section 2: Installation .................................................................................................................................................................................................................................... 5
Section 3: Mounting.......................................................................................................................................................................................................................................7
Section 4: Operation....................................................................................................................................................................................................................................13
Section 5: Technical Support.......................................................................................................................................................................................................................20
Section 6: Safety & Maintenance................................................................................................................................................................................................................22
Section 7: Regulatory Information...............................................................................................................................................................................................................24
Section 8: Warranty Information..................................................................................................................................................................................................................28

SW601960 Rev. F, page 4 of 31
User Manual –32/42/43/5543L Series IDS
Section 1: Introduction
Product Description
Your new touch display combines the reliable performance of Elo Touch Solutions touch products with the latest
developments in touch technology and display design. This combination of features creates a natural flow of
information between a user and the touch display.
This widescreen touch display incorporates an active matrix thin-film-transistor LCD panel to provide high quality
display performance. Its Full HD resolution of 1920x1080 is suitable for displaying graphics and images. Its LED
backlight significantly reduces power consumption and eliminates mercury (compared to CCFL-backlit panels).
Other features that enhance this LCD monitor’s performance are Plug & Play compatibility and on-screen display
(OSD) controls.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to maximize the life of your unit
and prevent risks to user safety. See the Safety & Maintenance Section for more information.
This manual contains information that is important for the proper setup and maintenance of the unit. Before setting up and powering
on your new touch display, read through this manual, especially the Installation, Mounting, and Operation Sections.

SW601960 Rev. F, page 5 of 31
User Manual –32/42/43/5543L Series IDS
Section 2: Installation
Unpacking the Touch Display
Open the carton and verify that the following items are present:
•Touch display
•Mounting brackets
•Quick Install Guide
•VGA cable
•HDMI cable (ETXX43L-XXWA models only)
•DVI cable (ETXX43L-XXAA models only)
•USB cable (not available for ETXX43L-0NXX models)
•International power cables
•OSD Remote
•Japanese language regulatory information pamphlet
Connector Panel & Interfaces
Note: DVI or HDMI are available on certain models only.

SW601960 Rev. F, page 6 of 31
User Manual –32/42/43/5543L Series IDS
Touch Display Connections
1. Connect a video cable from your host computer to the monitor. For VGA cables, tighten the video cables
screws for best performance.
2. Connect the USB touch cable between the monitors USB connector and your PC’s USB port. (Not
applicable for No Touch models)
3. Connect the power cable to the monitors input power jack and the AC power outlet.
4. The touch display ships in the ON state.
Installing the Touch Technology Software Drivers
No additional drivers are required for your projected-capacitive touch display with Windows 7 and 8 operating systems, it uses Windows HID drivers.
To download latest touch drivers:
1.Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.aspx
2.Select the operating system from “Operating System” dropdown menu.
3.Select the technology from “Technologies” dropdown menu.
4.Click on the driver version required for your touch display.
5.Click “Accept” once you are directed to the “Driver License Agreement” page.
6.Enter you email address, Click on “Next Step”. Your driver download will start automatically.
7.If you are a new user, fill in the required information and Click on “Register”. Your driver download will start automatically.

SW601960 Rev. F, page 7 of 31
User Manual –32/42/43/5543L Series IDS
Section 3: Mounting
General Mounting Information
The OSD text can be rotated between portrait and landscape mode through the OSD menu to better suit your
mounting orientation.
Portrait and Landscape Mode
The monitor can only be installed in portrait or landscape mode following the below diagram. The THIS END UP
sticker will point up.

SW601960 Rev. F, page 8 of 31
User Manual –32/42/43/5543L Series IDS
For Elo Part Numbers E220625, E589724, and E444804:
Portrait mode can only be installed in the 90 degrees orientation such that the Elo logo on the back is rotated to the
right and the cables are connected from the left side, as the following image shows.
Landscape mode can only be installed at 0 degrees such that the Elo logo is on the back is not rotated and the
cables are connected from the bottom, as the image below shows.
Insert cables from
this side

SW601960 Rev. F, page 9 of 31
User Manual –32/42/43/5543L Series IDS
Side Mount Brackets
Threaded holes are provided on the sides of the monitor for mounting using the provided brackets. Side mount
brackets are compatible for ET3243 IntelliTouchDual Touch, ET4243L IntelliTouch Dual Touch, and ET5543L
TouchProonly.
For ET3243L:
Insert cables from this side

SW601960 Rev. F, page 10 of 31
User Manual –32/42/43/5543L Series IDS
For ET4243L:

SW601960 Rev. F, page 11 of 31
User Manual –32/42/43/5543L Series IDS
For ET5543L:

SW601960 Rev. F, page 12 of 31
User Manual –32/42/43/5543L Series IDS
Flush Mount Brackets
Flush mount brackets are included in an optional kit for ET3243L TouchPro.
For ET4343L TouchPro, it is included in the accessories box.

SW601960 Rev. F, page 13 of 31
User Manual –32/42/43/5543L Series IDS
Rear VESA Mount
For ET3243L:
A four-hole 400x200mm mounting pattern for M6 screws is provided on the rear of the monitor. The VESA
FDMI-compliant counting is coded: VESA MIS-F, 400, 200, 6.
For the ET4243L/ET4343L/ET5543L:
A four-hole 400x400mm mounting pattern for M6 screws is provided on the rear of the monitor. The VESA
FDMI-compliant counting is coded: VESA MIS-F, 400, 400, 6.
Refer to www.elotouch.com for dimensional drawings.

SW601960 Rev. F, page 14 of 31
User Manual –32/42/43/5543L Series IDS
Section 4: Operation
Power
To turn the touch display on or off, press the touch display power button on the OSD controller once.
The Power Status LED on the OSD controller functions according to the following table:
Touch Display /Computer Module Status
LED Status
OFF
OFF
SLEEP
PULSING
ON
ON
The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications,
refer to technical specifications on the Elo website at www.elotouch.com.
Touching the screen will bring the attached host PC out of SLEEP mode (similar to moving the mouse or pressing a
keyboard key).
To improve reliability and reduce wasteful power consumption, disconnect the AC power cable from the monitor
when long periods of disuse are planned.
Touch
Your touch display is factory-calibrated and does not require manual calibration (unless the input video is not fully
scaled to the native resolution, or the touch experience needs to be calibrated to a specific user).
IntelliTouch Dual Touch Touchscreen Technology
When connected to Windows 7 or 8 computers, the touch display can report two simultaneous touches. Refer to
Section 2, Section “Installing the Touch Technology Software Drivers” to find instructions to download the latest
touch drivers.
The IntelliTouch Dual Touch touchscreen can be re-calibrated to your displayed video image, if needed, through the
calibration function in the Elo driver control panel. The driver can be downloaded from the Elo Touch website.
The IntelliTouch Dual Touch touchscreen can be re-calibrated to your displayed video image, if needed, through the
calibration function in the Elo driver control panel.

SW601960 Rev. F, page 15 of 31
User Manual –32/42/43/5543L Series IDS
The IntelliTouch Dual Touch driver will only support multiple monitor if they are all using the IntelliTouch Dual Touch
technology.
For more configuration options, double click on the EloConfig desktop shortcut to open up the Elo Touchscreen
Configuration screen.
TouchPro Technology
When connected to Windows 7 or 8 computers, the touch display can report 10 simultaneous touches. When
connected to Windows XP computers, the touch display reports single touches.
No additional drivers are required for this technology to work with Windows 7 and 8, it uses Windows HID drivers.
Refer to Section 2, Section “Installing the Touch Technology Software Drivers” to find instructions to download the
latest touch drivers for Windows XP.
No calibration is required for this technology.
For ET4343L and ET5543L, 12 simultaneous touches are supported.
Gesture Support
The IntelliTouch Dual Touch and TouchPro technology enables several gestures that support single and multiple
contacts. Refer to the Microsoft Website http://msdn.microsoft.com/en-us/library/dd940543 on the various gestures
that are supported in Windows 7 and Windows 8.1.
Video
A display’s native resolution is its width and height measured in number of pixels. Generally, for best performance,
an image displayed on this monitor will look best when your computer’s output resolution matches this monitor’s
native resolution of 1920 x 1080.

SW601960 Rev. F, page 16 of 31
User Manual –32/42/43/5543L Series IDS
For computer output resolutions at non-native resolutions, the monitor will scale the video to its panel’s native
resolution. This involves stretching or compressing the input image as needed in the X- and Y-dimensions to fit the
display’s native resolution. An unavoidable byproduct of the scaling algorithms is a loss of fidelity when the
computer’s output video image is scaled by the monitor to fit the display. This loss of fidelity is most apparent when
viewing feature-rich images at close distances (for example images containing small-font text).
Your touch display will likely not require video adjustments. However, for analog VGA video, variations in video
graphic card outputs may require user adjustments through the OSD to optimize the quality of the touch display’s
displayed image. These adjustments are “remembered” by the touch display. Also, to reduce the need for
adjustments for different video mode timings, the monitor correctly scales and displays some of the video industry’s
most common video timing modes. Refer to the technical specifications for this monitor at http://www.elotouch.com
for a list of these Preset Video Modes.
Elo recommends using the Content Management System, O/S scheduling settings, or RTC scheduling settings
and/or EloView commands to manage duty cycle. This will enable power savings and trouble free operation
throughout the life of the monitor.
On-Screen Display (OSD)
Four OSD buttons are located on a wired control box. These can be used to
adjust various display parameters. The buttons and their functionality are:
Button
Function when OSD is not displayed
Function when OSD is displayed
Menu
Display OSD Main menu
Return to previous OSD menu
Display OSD Contrast submenu
Decrease value of selected parameter / select previous menu item
Display OSD Brightness submenu
Increase value of selected parameter / select next menu item
Select
Display Video Priority submenu
Select parameter for adjustment / select submenu to enter
Using the OSD buttons controls an on-screen graphical user interface which displays on top of your input video,
allowing intuitive adjustment of the following display parameters:

SW601960 Rev. F, page 17 of 31
User Manual –32/42/43/5543L Series IDS
Parameter
Available Adjustment
Brightness
Increase/decrease monitor brightness.
Default: maximum
Contrast
Increase/decrease monitor contrast
Default: best gray-shade performance
Clock
Allows fine adjustments of the panel’s pixel dot clock.
Only applicable for VGA input video
Phase
Allows fine adjustments of the panel’s pixel dot clock phase.
Only applicable for VGA input video
Auto Adjust
Automatically adjusts the system clock to the input analog VGA video signal, affecting the H-position, V-position, Clock, and Phase menu items.
Only applicable for VGA input video
H-position
Moves the image horizontally on the display in single-pixel increments. Default: centered
Only applicable for VGA input video
V-position
Moves the image vertically on the display in single-pixel increments. Default: centered
Only applicable for VGA input video
Aspect Ratio
Switches the scaling method between Full Scaling and Maintain Aspect Ratio. Default: Full Scaling
Full Scaling –scales the X- and Y-dimensions of the input video (up or down as needed) to the display’s native resolution.
Fill to Aspect Ratio –Assuming a landscape orientation and an input video with aspect ratio smaller than 16:9, scales the Y-dimension of the input video (up or down as
needed) to the display’s Y-resolution, and scales the X-dimension to maintain the input video’s aspect ratio (and fills the rest of the display with equal black bars on the left
and right)
Other touchscreen technologies may need recalibration when switching between Aspect Ratio options.
Sharpness
Adjusts sharpness of the displayed images. Default: no sharpness adjustment
Only applicable at non-native input video resolutions
Color Temperature
Selects the display’s color temperature. The available color temperatures are 9300K, 7500K, 6500K, 5500K, and User Defined. If the User Defined option is selected, the
user can change the color temperature by changing individual R, G, and B gains on a scale from 0 to 100.
Default: User Defined with R, G, and B all set to 100.
OSD H-Position
Adjusts the horizontal location of the OSD menus on the display
Default: centered
OSD V-Position
Adjusts the vertical location of the OSD menus on the display.
Default: centered
OSD Timeout
Adjusts how long a period of OSD button inactivity the touch display will wait before closing the OSD. The adjustable range is between 5 and 60 seconds.
Default: 15 seconds
OSD Language
Selects which language the OSD information is displayed in. The available languages are: English, French, Italian, German, Spanish, Simplified Chinese, Traditional
Chinese, and Japanese.
Default: English

SW601960 Rev. F, page 18 of 31
User Manual –32/42/43/5543L Series IDS
Parameter
Available Adjustment
OSD Rotation
Selects the touch display mounting orientation between Landscape and Portrait to match your physical orientation. This adjusts the rotation of the OSD text.
Default: Landscape
Recall Defaults
Selecting “Recall Defaults” restores all factory default settings for OSD-adjustable parameters and for Preset Video Mode timings.
Note: This feature does not affect the OSD language setting. For 4243L units, both language and rotation are unaffected.
Video Priority
The monitor continually scans for active video on the VGA, DVI, and HDMI connectors.
This adjustment selects which of those input ports should be given priority to be displayed. The options are: VGA Priority, HDMI (for ETX243L-XXWA models) or VGA
Priority, DVI Priority (for ETX243L-XXAA models)
Default: HDMI (for ETX243L-XXWA models) or DVI Priority (for ETX243L-XXAA models)
All touch display adjustments made through the OSD are automatically memorized as soon as they are entered. This
feature saves you from having to reset your choices every time the touch display is unplugged or powered off and on.
If there is a power failure, the touch display settings will not default to the factory specifications.
OSD and Power Lockouts
Press and hold the “Menu” and “down” buttons for two seconds to enable/disable the OSD Locking feature. When
the OSD Locking is enabled, pressing any of the Menu, Up, Down, or Select keys will have no effect on the system.
Press and hold the “Menu” and “up” buttons for two seconds to enable/disable the Power Locking feature. When the
Power Locking is enabled, pressing the power switch will have no effect on the system.

SW601960 Rev. F, page 19 of 31
User Manual –32/42/43/5543L Series IDS
Real Time Clock Function
For touch displays with the RTC function installed, the “Miscellaneous” section of the OSD menu will have RTC
settings. Here you can use the OSD buttons to allow adjustment of the additional display parameters:
Parameter
Available Adjustment
Daylight Savings Time
Allows time to be changed by one hour to accommodate for daylight savings time change.
Default: Off
Time Setting
Allows time to be set in the 24-hour format of HH:MM:SS. The date can be set in the format of MM-DD-YYYY.
Default: On
Schedule
Enable/disable scheduling to automatically turn on/off the touch display. The on/off time can be set in a 24-hour format of HH:MM.
You can schedule which days the touch display will turn on/off by selecting each day with the OSD remote.
If prompted to set current time, the RTC schedule will be automatically be enabled to turn off at 1:00:00AM and turn
on at 7:00:00AM. This option can be turned off manually in the OSD menu under RTC settings.
Temperature Warning
The touch display contains a temperature sensor that can monitor the system temperature. If the touch display is
operated outside the specified temperature range, it will go into Thermal Protection mode. In this mode, the
brightness will be reduced in order to bring the system temperature back within the specified temperature range. The
brightness will not be able to be increased beyond the set value. After five minutes of use within the normal
temperature range, the touch display will automatically restore the brightness level back to what it was set at
previously. If the touch display is continuously operated outside the specified temperature range, it will shut off after
a 60 second on-screen timer.

SW601960 Rev. F, page 20 of 31
User Manual –32/42/43/5543L Series IDS
Wake on Touch Function
The touch display supports wake-on-touch functionality when the PC is in sleep mode. To enable this, please ensure
that the BIOS settings have enabled USB support during the S4 sleep cycle.
For touch displays with RTC function enabled, please make sure the Touch on Sleep mode is enabled in the OSD
menu, by selecting “Miscellaneous” and then enabling the “Touch” setting.
If you still are having trouble with Wake on Touch, please download the latest Elo drivers to allow the touch display
to use this function. Refer to Section 2, Section “Installing the Touch Technology Software Drivers” to find
instructions to download the latest touch drivers.